Furniture of America IDF-7529EX-T Jade Espresso Twin Bed Instructions / Ass

Download Furniture of America IDF-7529EX-T Jade Espresso Twin Bed Instructions / Assembly .PDF

967372 Downloads

1.56 MB .pdf

Save the instructions and store the Allen wrench or any supplied tool for later maintenance. IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE. FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY RESULT IN INJURY AND/OR PROPERTY DAMAGE. Parts List Hardware List #1 x 1pc Headboard Leg (Left) #A x 8pcs Bolt ɸ1/4" x 3-1/8" #2 x 1pc Headboard Leg (Right) #B x 8pcs Barrel Nut ɸ1/4" x 1/2" #3 x 1pc Footboard Leg (Left) #C x 8pcs Screw ɸ1/4" x 4" #4 x 1pc Footboard Leg (Right) #D x 8pcs Bolt ɸ1/4" x 1-3/16" #5 x 1pc Horizontal Bar Bed #E x 8pcs Hex Cap ɸ1/4" x 5/8" #6 x 2pcs #F x 18pcs Horizontal Bar Bed Wood Dowel ɸ10 x 40mm #7 x 1pc Footboard Panel #G x 8pcs Screw ɸ4 x 30mm #8 x 2pcs #H x 1pc Side Rail Allen Wrench 4mm Page 3 of 8 Parts List #9 x 2pcs Side Rail #11 x 1set Twin Slat Kit (10pcs) #10 x 2pcs Support Leg #6 #2 #5 #8 #10 #11 #1 #9 #9 #4 #10 #8 #7 #3 Page 4 of 8 Attach dowels (#F) on each end of the bar beds (#5,6), then align bar beds (#5,6) to the headboard legs (#1,2). THIS MAY LEAD TO COLLAPSE AND MAY CAUSE SERIOUS INJURY. Page 2 of 8 Before you begin, please read Page 2 of "Assembly and Care Advice". Some furniture comes with height adjusetment knobs underneath each leg. #A x 4pcs #B x 4pcs #B #2 #H #A #8 #1 #9 Align support legs (#10) to the side rails (#8,9), then #D x 4pcs #E x 4pcs secure by tightening bolts (#D) to hex caps (#E). After two weeks, check and tighten any loose hardware and repeat again every six months thereafter. Make sure all parts are properly aligned, then use the appropriate hand tool to completely tighten the bolts or screws. #F x 2pcs #F #8 #9 #10 #9 #10 #8 Secure side rails (#8,9) to support legs (#10) by tightening bolts (#D) onto hex caps (#E). #8 #10 #E #9 #D #10 #H Page 6 of 8 Insert dowels (#F) onto side rails (#8,9), then align side rails (#8,9) to each other as shown in the diagram. #E #D x 4pcs #E x 4pcs #D #8 #H #10 #9 #10 #8 Page 7 of 8 #9 Align footboard (#7) to the side rails (#8,9), then insert barrel nuts (#B) to the side holes of the side rails (#8,9). #F #C x 2pcs #F x 4pcs #C #4 #7 #5 #H #3 Page 5 of 8 Align side rails (#8,9) to the headboard (#1,2), then insert barrel nuts (#B) to the inner side holes of the side rails (#8,9). BASIC ASSEMBLY TECHNIQUES When lock or spring washer is used in an assembly, please make sure the lock or spring washer is placed between the larger flat washer and the head of the screw or bolt. To lower or to raise each leg, you need to turn clockwise or counterclockwise, respectively. Assembly Instructions For more information contact our team: [email protected] CM7529T ASSEMBLY RATING Tools Required For Assembly: The Assembly Rating is a 5-point system that shows the degree of effort needed in assembling a specific product (with 1 being easy and 5 being difficult). Make sure the furniture rests on a flat and level surface with each leg evenly touching the floor. Allen Wrench (Included) Phillips Screwdriver (Not Included) EASY DIFFICULT 2 PERSONS RECOMMENDED Page 1 of 8 Rev: 19-04-10 FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY. Secure by tightening bolts (#A) onto barrel nuts (#B)