EagleTac MX25L2

投稿日: Sep 12, 2012 2:33:13 AM

※在庫表示がとなっている商品は在庫がなくメーカーからお取り寄せを行う商品です、納期が一ヶ月以上かかる場合がございますので等の通常販売の品とは別々にご注文ください、

• • base

    • 専用Li-ion充電池内蔵

    • 充電機能も本体に内蔵

    • ACアダプタは付属しません

    • 写真と同じステンレスベゼル

  • kit

    • baseに以下のアクセサリーが追加されます

    • diffuser filter, yellow filter, green filter, blue filter

    • w/ self-retention device

    • AC-DC adapter

    • Automobile 12V DC adapter

  • kit SBT-90

    • 付属品はkitと同じ

    • LEDがSST-90ではなくSBT-90（写真左SST-90、右SBT-90）

• • • SST-90はXM-Lと同系統の照射パターンですが、SBT-90は超スポットです

• • LEDの違い

    • SST-90

      • Center lux: 55,100 lux

      • Center spot angle: 7°

      • Spill light angle: 58°

      • Beam distance: 513 yards / 469 meters

Maximum brightness 2850 LED Lumen

Maximum lumen output

LED lumen

SST-90 P-bin: 2850¹-2530/1071/210/19

SBT-90 MB: 1500¹-1330/560/110/9

ANSI lumen²

SST-90 P-bin: 2210¹-1935/820/161/16

SBT-90 MB: 1180¹-1045/438/87/7

Turbo boost technology

1) Turbo boost technology is activated every time you turn on at turbo output setting. It offers 20% more power to the LED for the first 200 seconds at turbo mode.

2) ANSI FL-1 lumen is the total overall light output being emitted from the flashlight. This measurement is generally more accurate as it takes into consideration the loss from reflector/lens/bezel. EagleTac ANSI FL-1 Lumen output is measured using a calibrated integrated sphere one minute after turning on the flashlight.

Top binned LED

Cool White LED

SST-90 P-Bin LED

SBT-90 MB LED

Luminus is registered trademark of Luminus Devices.

Color tint selection

Cool White LED

This gives you the maximum brightness output in its class and maximum beam distance.

Neutral White LED

If you need awesome beam output out in the woods, or areas with a lot of green vegetation, use our neutral white LED as it offers higher CRI (Color rendering index). Neutral white LED renders color like the sun in the afternoon. Neutral white LED is approximately 7-10% dimmer than our top binned cool white LED, but it's well worth the ability to see the real color of your surrounding.This gives you better color rendition and more accurate color relative to cool white LED.

SST-90 P-bin LED

Crazy 2120 ANSI lumen, excellent far projecting performance, excellent beam profile, great for close-up use with lowered brightness.

(Cool white LED beam profile shown above) Neutral white LED shares the same beam profile as its cool white version.

SBT-90 MB LED

Crazy far projecting performance.

Output color transformer

Red color filter

Low light application.

Yellow color filter

Design to use in rain and fog. Also ideal for caving.

Blue color filter

Low light application. Great for investigation and inspection.

Green color filter

Great for hunting and fishing lighting.

Spot and floody beam

Diffused beam

Use the optional diffused filter to instantly transform between spot and floody beam. The floody diffused beam is great for close up work.

Versatile output Four brightness levels

• • Lx2

• • L

• • M

• • T

• • AUX1

• • AUX2

• • AUX3

• • AUX4

• • AUX5

• • AUX6

• • AUX7

Clicky on/off side switch & Twisty head

Easy on/off operation

Turn on the light by press and release the on/off button switch (<0.4s). To turn off the light, press and release the switch again.

Momentary on/off

Press and hold the button switch for immediate output. Release the switch to turn off the light.

Output adjustable

Twist the head to select between four output brightness levels. You can pre-select the desired output level before turning on the flashlight.

Instant 100% output

At any output level, press and hold the flashlight for 100% output. Release the button to return to previous level.

Instant strobe output

At any output level, double press and hold the on/off button switch for strobe output. Release the button to return to previous level. This also work when the flashlight is off.

Access hidden auxiliary modes

With the head at tight position (1st level), loosen to 3rd (or 4th level) and tighten the head within one second to enter AUX. setting. Repeat to cycle through all settings. Turn off the light or loosen the head to quit.

Programmable settings

To switch between tactical mode (default) and regular mode, turn on the flashlight at 1st level, dial to 2nd level and then back to 1st level for five times within five seconds.

Turbo boost technology

This is activated every time you turn on at turbo output setting. It offers 20% more power to the LED for the first 200 seconds at turbo mode. It’s normal for the light to get warm at such level. Do not leave the light running unintended.

Maximum runtime Ultra efficient circuit.

Reliability that you can count on

We design this circuit to survive the toughest torture environment including: 1) repeatedly over-night burn-in test w/ minimal cooling, 2) over input voltage test of up to 13V, 3) over-driven output current test of up to 10A, and 4) high temperature duration test.

Our experienced electronic engineers ensure all components are working at its maximum efficiency and highest stability within the thoroughly planned circuit layout. All chosen electrical components in this circuit design have good amount of headroom to ensure high stability in long term usage.

Inside the C9500 SEL

This circuit uses the highest efficiency current mode controller from Linear technology. Linear techology is known as making world-leading high-end integrated circuit, and this controller that we're using belongs to their exotic class, in terms of crazy performance and high cost. This highly efficient synchronous buck current regulated circuit controls the precious amount of current that goes through the LED at all output levels. This results in constant brightness output regardless of LED variation, battery voltage, and temperature change. The Low EMI management and quick soft-start design provide clean electricity for the circuit and LED to enhance their service life.

Our synchronous buck converter is more technologically advanced and compact than regular buck converter. It also allows more board space for our exceptionally low DCR mosfets, rugged & shielded power inductor, and low ESR tantalum capacitors. This together leads to very high efficiency and lower required input voltage to current regulate.

The microprocessor is programmed to provide handy and easy-to-use interface for the users. When the flashlight is turned off, it shuts off all unnecessary components and waits to respond to user command at very low standby current (uA).

Excellent runtime & efficiency

MX25L2 runs for 200+ hours on its lowest brightness level. The current regulated circuit design allows constant output throughout its runtime for all output levels without LED flicking.

At its highest brightness output, MX25L2 current regulates for 1.3 hours with the standard R44 battery pack.

Not only we care about the LED runtime, we also care about the runtime when the LED is turned off. The standby power consumption is only measured in merely uA level, which translates to years of standby time period, just like your TV remote control.

Rich features

• • • Superme

    • handling

• • • Built-in rechargeability

• • • Battery & secondary LED indicator

• • • Reliable switch

• • • Smart head

    • design

• • • Tail-stand

    • ability

Supreme handling

The CNC precisely cut and rolled square-shape knurling provides a sure grip throughout the entire flashlight body. The super compact size and light traveling weight make it very handy to operate, even with one hand. It also allows tail-stand for ceiling bounce.

Built-in rechargeability

Rechargeable edition

MX25L2 has integrated quick li-ion charging system for your convenience. The high current charging system (using CC/CV method) offers 36% charged capacity within the first hour of charging (R44), combined with crazy lumen output and huge battery capacity, make MX25L2 the ultimate duty flashlight ever produced.

During fast charge status, the secondary led indicator lights up in blue color. When charging is completed, the indicator turns dim. A three hours safety timer is also implemented for safety protection (indicator turns off after timer is expired). The charging system works with our miniature AC-DC adapter that is UL listed, FCC certified, PSE certified or TUV certified depending on the safety requirement of your location. It can also be charged with 12V cigarette lighter socket in your car with our automobile DC adapter.

The charging system features "soft charging" feature to charge low voltage battery with lower current to enhance the battery life. For this reason, when the battery is nearly drained, the charging circuit may only reach to 90%+ capacity within the three hours timer. To reset the timer, simply remove and re-insert the charging plug anytime during charge.

Secondary LED indicator & Battery

LED indicator

This secondary LED indicator lets you know where you are exactly at. When the battery is full, it lights up in blue color. When it’s half way done, it lights up in red color. When the battery voltage is further reduced, it lights up in blinking red color. For user-friendly reason, the secondary led will only lights up for ten seconds after turning on the flashlight, or after changing the output. When the battery is almost out (battery protection circuit may kick-in at any time), the main LED blinks once every 30 seconds to remind you the light will shut off at anytime. Lowering the output by one level will significantly increase the remaining runtime.

Rechargeable battery pack

EAGTAC 7.4V battery pack is protected with ic circuit to prevent over-charge, over-discharge and short circuit. Batteries within each individual pack is balanced and matched in terms of internal resistance, voltage and capacity to ensure long service life and great reliability. R44 battery pack (44.4Wh) comes standard with MX25L2 flashlight. User can also purchase additional R44 battery pack for backup usage.

Button switch and twisty head

Signal switch

MX25L2 uses durable signal switch that is rated with 500,000 cycles of operating life. No current goes through the on/off switch translate to high efficiency, reliable switch mechanism, quiet and sparkless operation. The twisty head uses reliable mechanical spring loaded nodes to detect body movement for brightness and output adjustment.

Smart head design.

Excellent thermal path

We maximize LED output and its service life by dramatically reducing the thermal resistance between the LED and the heatsink. Maximizing the contact surface area between parts also help the LED heat dissipation.

Turbo head upgrade

We offer a turbo head upgrade head for tighter beam and brighter hot spot. To exchange the head, simply un-twist the regular head and replace it with the turbo head.

Durable structure against impact

The stainless steel bezel provides highly drop resistance. O-ring is used as cushion to protect and waterseal the harden waterwhite glass lens which is vacuum coated with anti-reflective layers. The machined thread on the head makes front attachment like filters and other accessories very conveniently.

Tail-stand

Flat tailcap

The MX25L2 comes with a flat tailcap for

tail-standing ability. User can also attach

lanyard to the back of the tailcap securely.