Embedded Files
Adnan Naama Abood, & Tahar Salah Habeb
Technical College, Baghdad / Iraq
DOI: https://doi.org/10.17656/jzs.10184
Abstract
The present work encompasses the grains refining of microstructure of Zn-Al alloy (ASTM B669 ZA-27)
ingots without addition of refining agents or using stirring, that is, by using the New Rheocasting (NRC).
AISI 316 stainless steel mould is employed with inclination angle of 75o and 1.2 V/A ratio. The pouring
temperatures are 532 oC, 522 oC, and 502 oC, while the quenching occurs at different temperatures. The
examination shows that all NRC ingots have microstructure of refined equaxial grains in the range of 27-
36 μm, while the percentage of volume fraction of α-Al phase was varied from 0.56 to 0.76. The value of
circularity was in the range of 1.33-1.65. The NRC ingots achieved less coarsening kinetic than critical
value which shows that there is a limited increase in the grain size and coalescence of reheating. Tensile
strength, Yield strength, and Elongation of ZA-27 alloy which was made by NRC process, increased to
18%, 11%, and 32% respectively compare to Gravity Die Casting (GDC) ingots due to formation of
equaxil grains along all the cross section in addition to smaller grains size.
Keywords: New Rheocasting, Zn-Al alloy, Pouring Temperature, Quenching
Temperature, Equaxial Grain, Mechanical Properties.
References
1. Kaufmann, H. & Wabusseg, H., "Metallurgical and processing aspect of NRC semi– solid casting technology", Aluminum, 2000, 76,. 69-75.
2. Young, K. & Eisen, P.,"SSM technological alternatives for different application ", Metallurgical Science and Technology, 2000, 18, 11-15.
3. Winterbottom, W. L., "Semi–solid forming application high volume automotive products", Metallurgical Science and Technology , 2000, 18,. 5-10.
4. Kleiner, S. & Beffort, O. , "Microstructure and mechanical properties of squeeze cast and semi–solid cast Mg–Al alloys" , Journal of Light Metals, 2002, 277-280
5. Flemings, M. C., "Behavior of metal alloys in the semisolid state" Metallurgical transactions B, Vol .22B, 1991, 269-292.
6. Kirkwood, D. H. , "Semi-solid processing of high melting point alloy" , proceedings of the 4th International Conference on Semi-solid Processing of Alloys and Composites ,Sheffield , 1996, 320-325.
7. Tzimas, E., "Evaluation of Volume Fraction of Solid in alloys Formed by semisolid processing" Journal of Materials Science 2000, 5319-5329.
8. Yurko, James A. & Raul, A., "Commercial development of the Semi-Solid Rheocasting process "Metallurgical Science and Technology". 2003, 21 (1), 10-15.
9. Abood, Adnan .N., "Design and Characterization of Advanced semi – solid casting processes" a thesis of PhD submitted to the Department of Production Engineering and Metallurgy University of Technology, IRAQ , 2003.
10. Zhang, B.& Garro, M., " Dendrite Arm Spacing in Aluminum alloy cylinder heads produced by gravity Semi-Permanent mold, Metallurgical Science and Technology2003, 21, ( 1), 3-9.
11. Rice, Chris S. & Mendez, Patricio F., “Slurry-Based Semi- Solid Casting”, Advanced Materials and Processes, 2001, 159, (10).Flemings, M. C.," Solidification processing", McGraw–Hill, New York, 1974.
Page updated
Report abuse