Undershirt

• Undershirt is constructed of tan coloured linen or linen-look fabric

• Undershirt is long sleeved and tucks into the gloves

• Undershirt is weathered to look lived in and well worn

• Collar of undershirt should be visible at opening of vest

Vest

• Vest is constructed of dark brown faux leather or leather-like material.

• Vest closes in front and closure is not visible

• Front of vest is constructed of an upper and lower panel on each side

• Vest has a layered shoulder detailing that extends out past the left arm hole that is constructed from the same material as the vest

• Vest is moderately weathered and should appear lived in and well worn.

Optional Upgrades:

• Undershirt is made of dyed nubby silk noil.

• Vest is made of genuine leather.

or

• Vest is made from genuine leather embossed with a light crosshatch patterning.

• Duster is constructed of a dark brown fabric such as cotton duck or canvas

• Duster should be weathered in accordance with life on a desert biome environment

• Duster is held in place by a strap made from the same fabric as the rest of the duster and that has a decorative clasp closure

  • Clasp closure design should appear as in the reference photo

• Duster should be approximately knee length

Optional Upgrades:

• Clasp is made from metal

• Gloves are made from a dark brown faux leather or leather-like material

• Gloves are a welding gauntlet style and extend almost to the elbow

• Gloves flare out slightly at the opening

• There is a defined band at the opening of the glove with a row of stitching at the centre and a double row of stitchng where it attaches to the rest of the glove

• The midsection of the glove has a sewn quilted pattern as shown in the reference photo

• Gloves appear sturdy and should be weathered to look lived in and well worn

Optional Upgrades:

• Gloves are made from genuine leather

• Belt is made of two layers: an underbelt and the primary belt.

• Underbelt is made from a dark brown faux leather or leather-like material that is weathered to look lived in and well worn

  • Brown shade used should be a minimum of one shade darker than the brown of the vest and primary belt

• Underbelt should appear to be ribbed or constructed of 1/2-3/4" strips of leather

• Underbelt should extend out from beneath the primary belt by 1-1.25" above and below.

• Primary belt is made from a dark brown faux leather or leather-like material and weathered to look lived in and well worn

• Belt buckle is a weathered bronze colour and circular in shape, diameter not to exceed the width of the primary belt

• Two bronze rivets are visible at the bottom of the right side of the belt near the buckle, approximately 3-3.5" apart.

• Primary belt has a row of small stitches down the center of the belt lengthwise.

Optional Upgrades:

• Underbelt and primary belt are constructed from genuine leather

• Buckle on primary belt is made of metal

• Pants should be constructed from a dark brown cotton duck or canvas material similar to the material used for the duster

• Pants have two faux leather or leather-like material strip detailing along the legs lengthwise which end just above the knee

• Pants should be relaxed fit but not tight, and should tuck into the tops of the boots

• No fly or closure should be visible

• Weathering should be visible along strip detailing

Optional Upgrades:

• Detailing on pants is genuine leather.

• Boots should be a dark brown similar to the colour of the underbelt and made of faux leather or a leather-like material

• Boots should appear heavy and sturdy and be weathered in accordance with life in a desert biome environment

• Half chaps should be made of a faux leather or leather-like material 

• Half chaps should cover the shaft of the boot and extend to just below the knee on top and to the heel in the back and on the sides.

• There should be a seam that divides the half chap into vertical halves

• There are three bands around the shaft of the half chap that are made from the same material as the half chap and approximately an inch in width which are weathered in the same way as the rest of the half chap.

  • The top of the three bands should be at the top of the shaft of the half chap

Optional Upgrades:

• Half chaps are made from genuine leather

• Blaster pistol is a modified combination of a Steyr M1912 and a PSS-43

• Blaster should fit comfortably in the belt holster

• Blaster should be constructed from a sturdy material such as PLA, resin, hard rubber or other hard plastic

  • If blaster is 3D printed, no print lines should be visible

• Blaster should be painted and weathered as shown in the reference photo

Optional Upgrades:

• Blaster is made from metal.