Team Robot Webpages (and contest results)
Click here to watch the Contest Live: Wed June 10 2009, 11:30am-2:30pm
Contest Results and Team Rankings will be Updated Live on the Web
rathi Basin, located in Arathi Highlands, is a fast and exciting Battleground. The Basin itself is rich with resources and coveted by both the Horde and the Alliance. The Forsaken Defilers and the League of Arathor have arrived at Arathi Basin to wage war over these natural resources and claim them on behalf of their respective sides. (This robotic interpretation has been inspired by Chris Cassidy.)
General Contest Information: Have your robot claim the battleground resources (the orange balls) before the robot on the other side does by getting them to your side of the battlegrounds! At the same time deploy your battle forces (the blue rings) to the other side of the battlegrounds to over run them and claim them as yours.
In the robotic interpretation there are two sides to the playing field which is split lengthwise as shown below. The robots compete head to head, each starting on a different side of the table, designated as Starting Areas A and B. A primary rail runs down the center of the playing field, while two secondary rails run lengthwise on either side of the table. On the primary rail are located the battleground resources (orange balls), with the tie breaking resources being the central gold ball. Each side has a bin adjacent to their starting area where resources can be safely stored. The objective of the contest is deploy as many as rings possible onto your opponents side of the playing field, while also bringing the resources onto your side of the table and even better into your bin.
Robot Playing Field
Scoring is as follows:
40 points for every Ring that ends up on the opponent's side of the table.
10 points for every Ball that ends on your side of the table.
15 points for every Ball that ends up in your bin.
The gold ball on your side of the table or in your bin is a tie breaker, and scores like an orange ball.
All scoring will be done at the end of the 1 minute contest, and judges rulings are final.
Being on a side of the table is defined as:
The center of a ball or ring must be in the vertical space over the flat bottom playing surface of your side (i.e. inside the side and central rails surrounding the flat surface of the playing field). All scoring will be done at end of contest, after parts stop moving. If a ball or ring is off the table it will not count, and if a ball or ring is tossed by one robot back onto the other side of the playing field, only the final location of the part will impact scoring.
Robot Constraints
Each MAE3 design team will build a robot that will compete head-to-head on the contest table. The robots will be arbitrarily assigned to start in either the right or left starting areas. The starting size of each machine is limited to a cube defined by a test box in the lab (approximately with a base of 10”x10”) . Note, a rail passes through the starting area, and robots can be attach to this rail, as long as the robot setup time does not exceed 2 minutes. The contest will run for a 1 minute time period.
There will be four playing fields built to accommodate all students in the class, and manufacturing tolerances will results in small variations between the contest tables. It is the design team's responsibility to develop a robot that will work on all contest tables.
Each team will build a machine using ONLY the kit parts described in the kit list. The kit includes 5 DC motors (2 will have gearboxes) and one solenoid. Electrical power will be provided from a power supply with a maximum of 5VDC output. The power will be controlled by the following switches:
Two 5 Volts DC switches
Two variable voltage switches. Note, the maximum current output is less in these switches. Since DC motors draw high current when they are not rotating, two non-geared motors may not start simultaneously if they are tied to the variable voltage source!
Each switch is Double Pole Double Throw (DPDT) switches, which can operate a DC motor in either direction. Note the kit contains five DC motors and one solenoid, but only four user controlled switches. More than one electrical device can be connected to a single switch, but the voltage may drop if a large current draw is placed on the power supply. Use of motors, solenoids, and switches will be covered in lecture and is described in the Mechanical Device textbook.
Contest Event Description
The contest will be held during the MAE finals period and will be open to the public. The contest will be held in a single elimination fashion (like a tennis tournament). During the lab period of the last week of classes, each section will hold a section-wide contest. The results of this contest will be used to seed the placement of the final contest. Thus teams that perform better during their section contest will have statistically easier contests in the early rounds. Since the number of teams in the class will not be exactly a power of 2, the higher seeded teams may get a "buy" during the first round. If necessary "wild card" teams will be selected to have a second chance in the contest, to ensure that all pyramid spots are filled.
Performance in the contest depends on numerous factors that do not relate to engineering quality of the robot, including driving skill and luck! The grade for the project will not be adversely affected by poor performance in the contest, but will be based upon:
Performance of the machine without an opponent, which will be video documented by the team and included in there oral presentation.
Effective communication of the design (orally and in final reports).
Documentation of the design process and justification of decisions made.
Analysis of machine performance.
Following good design practices.
A trophy will be presented to each member of the winning teams, and a number of machines will be selected for display in the Design Studio. Team members must work out among themselves who will keep the final machine (after their display period). Teams will post presentations and video of their robot on the class web page, which they can cherish forever.
General Rules
Only the tools and machine equipment in the Design Studio can be used to build the robot.
Energy Sources: The energy used by the devices in the competition must come solely from:
Potential energy derived through a change in altitude of the center of gravity of the machine
Potential energy achieved by the deformation of the springs provided by the Kit
Electrical energy derived through the umbilical during the 60 seconds when the power supply is energized.
Size: At the start of each competition, every part of the machine must fit unconstrained, inside the starting cube, whose base is completely aligned with the marked starting area on the playing field.
Umbilical Cables: The electrical connections will made to a single umbilical cord hung from above the table; one on each side of the table. The umbilical cord cannot be touched during the contest, and there will be some drag from the cable. Each machine must be designed to overcome this drag if necessary for motion of the machine. If requested a TA can ensure that the umbilical cable does not snag.
Detailed Rules
Judges and/or instructors will disqualify any device that appears to be a safety hazard.
Any machine that has flying parts must notify opponents, and all contestants must wear safety glasses during the machine operation.
If a projectile is used, for reasons of safety, it must have a frontal area greater than 2 inch squared.
Contestants will randomly be assigned to start on either side of the playing field.
A maximum set-up time of 2 minutes will be allowed at the contest table.
A maximum of 1 minute will be allowed for removal of all parts of each machine after each contest.
Operators may interact with their machine during a contest only through normal operation of the switch boxes (for example you cannot touch the machine with one's hands during operation).
It is allowable to adjust the configuration of the machine between contests; for example adjusting the configuration to the side of the playing field the machine starts on.
Each machine can only interact with the surface of the playing field and objects on the playing field.
The judges will wait until all the playing pieces have stopped moving before determining the winner.
Points will be awarded based upon the final location of the playing pieces, regardless of which machine moved them.
A playing piece will be declared out-of-bounds if it is off the playing field.
Damaging the playing field or the control boxes may result in disqualification.
Purposefully using the electrical cables for any purpose other than transmitting electricity is not allowed.
Gaining traction by use of adhesives, or by abrading or breaking the surface of the playing field is not allowed.
A machine may not contaminate with lubricant or other substance the playing field or an opponent's machine (internal lubrication of a machine is permissible).
Kit materials may not be changed chemically. DC Motors may not be rewound.
The paper that is attached to the acrylic in the kit cannot be used as a separate element in the machine. If any piece of paper is detached (even partially) from the acrylic it must be discarded.
The insulation must remain on the electrical wire in the kit except where the wire end is attached to another component, and there up to 0.5” of insulating can be removed.
The clear acrylic 0.25 thick is for testing. If you include any of this acrylic in your final machine, you must remove an equivalent amount of colored acrylic that was used in making the part.
Spare parts are available on a limited basis. Students should go to the tutors of their section to receive replacements for parts broken. Student can purchase replacement acrylic from upper campus machine shop or off campus (see door of Chris Cassidy's office for sources)
Machines may be designed to interact. However, it is not in the spirit of the competition to intentionally damage another machine and no part of the kit may be used in a manner that is intended to cause harm. Any device which is designed to chop, break, or penetrate another machine will not be allowed to compete. If you think your machine may be at risk for violating this rule, ask early before you build it! (see rule clarifications)
Machine advertisements and decorations must be of the nature that it does not offend any other students or audience participants (use common sense!).
All rulings of the judges will be final.
Any modifications or clarifications to the rules or kits will be posted on the class web page.
Clarification to Contest Rules:
Applying forces onto an opposing team’s robot that are large enough to break plastic pasts, while the opposing robot is in its starting area, will be deemed to be intentional harm to an opponent and can lead to disqualification.
Kit Part Rules
Each machine must be constructed solely from materials provided in the Kit listed below, i.e. one cannot substitute a 12"x16" piece of acrylic with a 6"x32" piece.
If a part of the kit is damaged it can be replaced from the scrap pile, as long as the design team can show that they could completely rebuild their machine solely from the kit.
In addition to the kit parts listed in the table, the following items may be included in the machine:
Nuts, bolts, and washers included in the Design Studio bin. These include bolts from size 2 to size 10, and metric screws for mounting the motors.
Only take nuts and bolts from the bin as you need them, and search through the spare bolt bin before taking more (we went through $1,500 in fasteners last year!)
Fasteners can be used only for fastening purposes, and thus must fasten at least two other parts together.
Adhesives; including hot melt glue, and acrylic adhesive.
Tape used ONLY for electrical insulation
Lubricants used only to reduce friction.
Nonfunctional decorations.
Replacement Material Policy
We have some extra material that can be used for experimentation. This material will be made available in the lab scrap bins. In addition each section tutor has access to a limited amount of replacement material for their section. If you need replacement parts, contact your tutor. Some replacement of "mistakes" made to kit parts will be available, but supplies are limited, and replacement is not guaranteed.