Tiger Replacement Parts

Camco Replace All Plumbing Vent Kit to replace the toilet vent on the roof http://amzn.to/2owI2ZK

Quick connect blow-out adapter/plug, connects directly from air hose to city water connection for one man winterization. http://amzn.to/2nC85j2

City water inlet, always rusts out, can be cleaned up and painted, or http://amzn.to/2o4fRP1 Check camping world for this one, they are usually the cheapest around at ~$13

A low budget, low profile roof vent. When my son forgot to close the roof vent, this was a quick and easy low profile replacement. http://amzn.to/2ongiEQ It doesn't come with screws or putty tape, get that here: http://amzn.to/2o45V8d I have a Fantastic vent installed in the front, my only complaint is how fast it eats the controller batteries, I hear the new models are moving to infrared controls instead of radio control. Bought from Adohen Supply Co and highly recommend them if you are going with a Fantastic Vent.

I replaced rear most light, above the bed with this one for reading. http://amzn.to/2opKpgB

Replacement Self/Auto Resetting Circuit Breaker for house battery connection: https://amzn.to/39qjKVX

Heater Register Vent:

Lower profile heat register vent/rotaire from RV Designer, love how low profile they are, and the dampers are super easy to remove for our application. I trimmed mine with a pair of tin snips, however they are slightly smaller than the existing vents, so some modifications are required.

http://amzn.to/2nC0wJn for when this happens https://goo.gl/photos/qTia4Y3z9aW487VH9

Fuel filler hose:

Gates Nitrile Marine Hose 10'length 2"diameter, great for replacing your leaking fuel filler hose, you only need about 8ft. so you will have some left over.

http://amzn.to/2opQEBa

2" Receiver hitch extension:

Allows the bike rack and a small trailer at the same time.

I have a modified version of this http://amzn.to/2onjws3

I added the additional receiver to the top of the extension http://amzn.to/2pqPX8g but can be had cheaper at Walmart. The reason for the additional receiver portion is so that when I'm not using the rear rack, it can fit upright next to the spare tire.

Rear Tail Lights:

My Tiger's tail lights are 21" long 5.25" high. I have not found a direct fit replacement set for the Tigers. If you do happen to know of a source, please let me know.

A custom plate using whatever lights you prefer is an option. Here is one of mine that has been replaced with LED lights:

Water Pump Rocker Switch:

http://amzn.to/2fIM501

Exterior window seals:

For Astro/Safari vans through 94(note that your Tiger may be titled a 95 and still be a 94), these are not designed for the Astro/Safari vans, this is a viable alternative to a part that is no longer available, simply trim 1/8-1/4" from the end and they fit perfectly http://amzn.to/2z1fnii

Replacement Lift Panels

Non spring loaded piano hinges are usually available at your local home supply store, like Home Depot. Spring loaded are special order from most places. You could use two shorter hinges instead of 1 long one as well.

Here are the dimensions:

https://photos.app.goo.gl/TYCXWvnBENvtRzSB3

Replacement Door Catch:

Usually it's just the rubber that wears out on the 'plunger door holder', you can get new ones https://amzn.to/2P1ur7D : To improve on the setup, you can get an better catch that will make it less likely to close with a gust of wind. Check these out! https://amzn.to/2Mkvxgu or a smaller one here: https://amzn.to/2vDXeHo

Replacement Headliner:

Search your favorite supplier for "Perforated Automotive Vinyl". Decent amount of colors available, seam can be hidden under trim.

HydroFlame Excalibur II, aka HydroFlame 8500-II:

Blower Motor https://amzn.to/2q6kxGd

Plumbing:

I have had to do some plumbing repairs, and here are some of the parts I have used and some that are just handy. 3/8 grey PB(Polybutylene) is what was originally used. It's ok if installed and used properly, but PEX(cross linked polyethylene) is a much better replacement and available everywhere. I have replaced what I needed with PEX piping and Flair-it fittings, the flair-it fittings work on both PB and PEX and only have to be hand tightened.