Improperly vented exhaust fan
ASHRAE compliant Exhaust fan installed, sealed and insulated
Follow steps 1a-1h to install a wall termination for an exhaust fan vent
Terminations will be ducted to the outdoors.
Ensure termination does not exhaust into a carport or buffered space.
Ensure termination has appropriate clearances from other openings into the home. Terminations must be at least 3' from operable openings into the building, 10' from mechanical air intakes, 3' from property lines, and must have appropriate clearances from Category IV appliance vent terminations, to prevent exhaust from reentering house.
Vent terminations shall have screen material with no less than 1/4" and no greater than 1/2" hole size in any direction to prevent pest entry.
Follow instructions in work order and Identify where to install the termination in attic, floor or crawlspace.
Note the location of structural members, and plumbing and electrical lines.
Locate where to install the termination on the exterior of the home and trace outline of duct avoiding structural members and utilities.
Determine vent diameter and cut hole in exterior wall slightly larger, but not more than 1/4" larger, than the outer diameter of the vent shroud on the termination.
Take care not to cut any plumbing or electrical lines.
If installing termination through masonry or stone, use a core drill to cut hole
Whenever possible, install flashing under cladding to direct water away from penetration and preserve the integrity of the building envelope
Install a collar the same diameter as the outlet on the fan, or larger.
If collar is larger than exhaust fan outlet, a rigid transition shall be used.
Position vent termination flush against exterior.
Orient to allow damper(s) to close when not in use.
Secure to house using 4 or more exterior grade fasteners
Seal gap between termination and exterior of home with exterior grade caulk to prevent water intrusion.
Follow steps 2a-2h to install a roof termination for an exhaust fan vent
Terminations will be ducted to the outdoors.
Ensure termination does not exhaust into a carport or buffered space.
Ensure termination has appropriate clearances from other openings into the home.
Terminations must be at least 3' from operable openings into the building, 10' from mechanical air intakes, 3' from property lines, and must have appropriate clearances from Category IV appliance vent terminations, to prevent exhaust from entering house.
Vent terminations shall have screen material with no less than 1/4" and no greater than 1/2" hole size in any direction to prevent pest entry.
Identify location from inside the attic.
Choose location to minimize length of duct, turns and bends.
Trace outline on the roof sub-straight.
Drive a couple screws thru the sub-straight and thru roofing to transfer the location to the exterior.
Outside the house, trace the outline of the duct onto the roofing, using the pilot holes as a guide
From the exterior, cut out the hole for the duct slightly larger, but not more than 1/4" larger, than the outer diameter of the vent shroud on the termination.
Take care not to cut any structural members or plumbing or electrical lines.
For roof holes, pry up and break shingle tab seals around the top half of the hole to allow for installation of roof termination.
Trim shingles to lay flat and fit tightly around roof termination in a manner that will direct water away from termination, and prevent water intrusion into the building.
Install a vent cap under shingles and directly over the hole.
Trim shingles as necessary to fit vent cap.
Tuck top of roof termination flashing under shingles, and lay bottom of termination flashing on top of shingles to prevent water intrusion.
Seal the underside of the vent cap flange, nail holes, and shingles with roof sealant.
Secure to roof using 4 or more roofing fasteners.
Top fasteners should be installed under shingles.
Seal the nail holes, and edges of shingles with roof sealant.
Follow steps 3a-3h to install an Exhaust Fan
Follow work order to select exhaust fan location.
Be careful to avoid structural members and electrical and plumbing lines.
Inside the home, trace the outline of the fan on the ceiling.
If location was selected from attic, use pilot holes as a guide.
From inside the home, carefully cut the fan hole no greater than 1/4" greater than assembly.
Support the piece while cutting to prevent breaking larger hole.
Install the fan according to the manufacturers specifications. Aim the exhaust port in the direction of the termination
A backdraft damper will be installed between the outlet side of the fan and the exterior to prevent reverse air flow when the fan is off.
Ensure fasteners do not inhibit damper operation
Connect fan to commercial electricity.
Wiring will be installed in accordance with original equipment manufacturer specifications, and local and national electrical and mechanical codes.
Notice: This must be done by a Licensed Electrician.
Caulk or mastic all of the cracks between the drywall and the housing and all holes in the housing unit.
Follow steps 4a-4d to install a rigid metal or PVC duct
Refer to manufacturer's specifications to determine correct duct sizing.
Duct must be sized to allow for air flow needed and to prevent excessive noise.
Design a rigid metal or PVC duct that will connect the exhaust fan to the exterior termination.
Duct sizing, overall duct length and number of elbows should be within allowable manufacturers specs, and should be ran in the most direct route to minimize total duct length.
Cut and connect each piece of duct to allow for maximum air flow.
For metal duct connect with the crimped end furthest away from the exhaust fan to maximize flow of exhaust fan.
For metal duct Install 3 or more duct screws evenly spaced around the diameter of the duct at each connection
For PVC duct prime and glue all connections
Use mastic or UL181 Listed Tape to seal all seams and connections on metal duct
Follow steps 6a-6g to Insulate Rigid duct
Measure and cut insulated flex duct to cover duct between the exhaust fan and the termination.
Inside diameter of flex duct should be about 1" larger than the outer diameter of the duct.
The R-value of the insulation should be an R-8 or equivalent to local codes
Slip the insulation over the duct and stretch from end to end to ensure proper fit and coverage
Connect the duct to the exhaust fan and to the exterior termination
Slide outer sleeve over duct boot, adjust insulation to allow for full coverage, and secure outer sleeve with zip tie.
Support flexible ducts every 4' or less using a minimum of 1-1/2" wide material
Install support materials in a way that does not crimp ductwork or cause the interior dimensions of the ductwork to be less than specified
Support metal ducts every 10' or less using 1/2" or wider material
Use flow meter to test fan flow to ensure it meets flow requirements.
Educate client on the proper use and settings of the fan
Conduct a Worst Case draft test to verify Category I, II, and III appliances are venting safely before leaving home for the day.
Testing shall be recorded using the WAP Worst Case Draft Test form.