Fuel Pump Extractor Tool
It is used for removing and installation of Wing/center tank fuel pump of aircraft.
Torque Wrench (Ratchet type)
A torque wrench is a tool used to apply a specific torque to a fastener such as a nut or bolt. It is usually in the form of a socket wrench with special internal mechanisms. A torque wrench is used where the tightness of screws and bolts is crucial.
BSI Guide Tube-Ceo
These guide tubes are used to direct the articulating borescope to the specific area that is required.
BSI Guide Tube-Neo
These guide tubes are used to direct the articulating borescope to the specific area that is required.
Bleed Tester - Ceo
It is used for troubling shooting of engine bleed system's components such as Bleed/Solenoid valves of 7th A, B, C & 10th stage (ATA 75).
Accumulator Charging Tool (N2 Adapter)
It is used for N2 charging of Hydraulic / brake accumulator and cabin door dampers.
MLG Wheel Change Kit
It is used for replacement of main wheel assembly of aircraft.
NLG Wheel Change Kit
It is used for replacement of nose wheel assembly of aircraft.
Brake Change Kit
It is used for replacement of brake assembly of aircraft.
Brake Release Tool
It is used for braking torque of brake mounting bolts.
Aircraft Axle Jack
It is used for replacement of MLG/NLG wheel assembly & brake assembly of aircraft.
Nitrogen Cylinder Trolley (HP/LP)
N2 HP cylinder is used for charging of hydraulic / brake accumulators and cabin door dampers. While LP cylinder is used for charging of a/c tyre pr., lines purging during eco wash and sometimes to clear wash-basin drainage blockage etc.
MLG Door Safety Sleeves
It is used for locking MLG/NLG door for doing any maintenance activities in the close vicinity of L/G doors.
NLG Door Safety Pin
It is used for locking NLG door for doing any maintenance activities in the close vicinity of L/G doors.
Eco Wash Unit-Ceo/Neo
It is used for engine gas path cleaning.
Eco Wash Unit-CFM
It is used for engine gas path cleaning.
TDS Meter
A TDS meter is a small hand-held device used to indicate the Total Dissolved Solids in a solution, usually water. Since dissolved ionized solids, such as salts and minerals, increase the conductivity of a solution, a TDS meter measures the conductivity of the solution and estimates the TDS from that reading.
Water-Sensor
It is used for measurement of water content in oil ,hydraulic and other lubricants.It indicates water content output in % saturation or PPM.
Pneumatic Drill
A pneumatic drilling machine is designed to perform many functions such as drilling, reaming, countersinking, and tapping small or large holes operated by pressured air.
Power Drill
A power drill machine perform same functions as pneumatic drill but it is operated by battery pack/electric power.
Tap & Die Set
A tap & die set is used for making internal and external threads.This tool set is widely used by a Structure Technician.
IDG Charging Tool
IDG Charging Tool is used for servicing of IDG.
IDG Drain Tool
IDG drain tool is also used for servicing of IDG.
Oil Gun
It is used for servicing of air turbine starter (Ceo/CFM).
Measuring Jar
It is used for servicing of air turbine starter (Ceo/CFM).
Bucket
Use: Multipurpose
Funnel
Use: Multipurpose
Ice Box
Metal Tray
Use: Multipurpose
Jerry Can
Use: Multipurpose
Hand Grease Gun
Oil Can- (Nycolube oil/Hydraulic fluid-5606)
Paper Cutter
Use: Multipurpose
Poker
Use: Multipurpose
Fuel Drain Kit
Use: For draining water/sediments/fuel from wing/center tank.
Fuel Sampling Jar
Use: For Collecting fuel sample from wing/center tank or fuel/fuel bowser.
Fuel/Hydraulic Sampling Bottle
Use: To collect fuel/hydraulic fluids samples for laboratory test.
Tyre Pressure Gauge
It is used for checking tyre pressure of aircraft.