QiDi X-Plus Printers

Web Site: WWW.STEAMCLOWN.ORG | Contact: TopClown@STEAMClown.org | LinkedIn: Jim Burnham | TikTok: STEAM Clown

Consider Supporting my Open Source STEAM Curriculum Development -- Patrion: Jim The STEAM Clown  | Amazon: Amazon Classroom Wishlist,  

Caution & Safety  Considerations:

Primer:  "Aaron, I can imagine no way in which this thing could be considered anywhere remotely close to safe. All I know is I spent six hours in there and I'm still alive... You still want to do it?"

• As with any activity, please make sure you are using appropriate safety equipment.   If you are coding, writing, reading, or working a lab, make sure you stand up and stretch every hour or so,  Please consider any safety issues connecting to a Raspberry Pi, Arduino, computers and other electronic equipment.

QiDi X-Plus Printers

Introduction:

In the SVCTE Mechatronics Engineering class we have 2 QiDi X-Plus printers.  

Docs & Tutorial:

• QiDi X-Plus printer  - QiDi Site - ✨ Resources /  🖼️ Tutorial  

• QiDi X-Plus printer  Review - ✨ Resources /  🖼️ Tutorial 

• 3D-Print - Overview

• QiDi X-Plus printer  Slicer Software (QiDi Tools)

Tips & Tricks To Get Better Prints With The QiDi X-Plus printer  :

• Tip or Trick - <list information here>

• 
  

QiDi X-Plus printer   - Robot Club - Students Maintained and Updated QiDi X-Plus printer  Notes, Tips, & Tricks Tutorial - ✨ Resources /  🖼️ Tutorial  

Quick Start Tutorial:

Setting Up the Printer

New or Complex Vocabulary:

• Calibration: The process of adjusting the printer to ensure proper operation.

• Firmware: Software installed on the printer’s hardware that controls its operations.

Key Concepts:
This section provides a step-by-step guide on setting up the printer, including unpacking, assembling, and calibrating. Calibration is critical for ensuring accurate prints, and students will learn how to check the firmware version and adjust settings in the printer’s software.

Challenges:
Students might struggle with calibrating the print bed, as even small misalignments can cause print failures. Providing diagrams and video tutorials will help.

Tips and Tricks:
Always start with a small test print after setup to ensure the calibration is accurate before moving on to larger prints.

Not Working? FAQ:

• FAQ #1 - xxxx

• 
  

Setup, Leveling, & Calibration Tutorial:

• <add leveling and Calibration steps and setup...>

Maintenance Instructions and Links:

Nozzle and Printer head Cleaning

Parts

• The QiDi X-Plus printer is a proprietary printer... 

CHatGPT Tutorial Outline

1. Introduction to 3D Printing

New or Complex Vocabulary:

• Additive Manufacturing: The process of creating objects layer by layer.

• Extruder: The component that pushes filament through the hot end to print layers.

Key Concepts:
3D printing, also known as additive manufacturing, is a process of making three-dimensional objects by layering materials like plastic. This section introduces the history of 3D printing, its various applications in fields such as engineering, medicine, and product design, and how it has revolutionized prototyping and manufacturing.

Challenges:
Students may find it challenging to understand how additive manufacturing differs from traditional subtractive manufacturing methods (like cutting or milling), where material is removed to create the final product.

Real-World Applications:
3D printing is used to make custom prosthetics in healthcare, rapid prototyping in engineering, and even in construction, where homes are printed using concrete.

2. Components of a 3D Printer

New or Complex Vocabulary:

• Hot End: The part of the extruder that melts the filament.

• Print Bed: The surface on which the object is printed.

• Stepper Motors: Motors that control the movement of the extruder and print bed.

Key Concepts:
This section explains the primary components of a 3D printer: the extruder, hot end, print bed, and stepper motors. It breaks down their functions, helping students understand how each part contributes to the printing process.

Challenges:
Grasping how stepper motors precisely control the movement in all three axes (X, Y, Z) might be confusing. Visual aids and animations will help illustrate how these motors ensure accurate positioning.

Tips and Tricks:
Always ensure the print bed is clean and properly leveled before starting a print to avoid issues with adhesion.

Real-World Applications:
Understanding 3D printer components is crucial for troubleshooting and maintaining the printer, skills highly valued in industries that use 3D printing for manufacturing or prototyping.

3. Setting Up the Printer

New or Complex Vocabulary:

• Calibration: The process of adjusting the printer to ensure proper operation.

• Firmware: Software installed on the printer’s hardware that controls its operations.

Key Concepts:
This section provides a step-by-step guide on setting up the printer, including unpacking, assembling, and calibrating. Calibration is critical for ensuring accurate prints, and students will learn how to check the firmware version and adjust settings in the printer’s software.

Challenges:
Students might struggle with calibrating the print bed, as even small misalignments can cause print failures. Providing diagrams and video tutorials will help.

Tips and Tricks:
Always start with a small test print after setup to ensure the calibration is accurate before moving on to larger prints.

4. Generating a G-code File

New or Complex Vocabulary:

• Slicing: The process of converting a 3D model into a series of layers that the printer can read.

• G-code: The language used to instruct the 3D printer on how to print the object.

Key Concepts:
Generating a G-code file is one of the most critical steps in 3D printing. This section will guide students through slicing a 3D model using popular software such as Cura. It explains the significance of G-code, which tells the printer how to move, extrude filament, and build the object layer by layer.

Challenges:
Understanding how slicing works and configuring the right print settings (layer height, infill, and print speed) can be overwhelming. Detailed explanations and visual representations of the settings will help.

Real-World Applications:
Mastering slicing software is essential for printing functional parts in engineering projects or creating prototypes that can be used in various industries.

5. Common 3D Printer Parameters

New or Complex Vocabulary:

• Infill Density: The amount of material inside the print.

• Layer Height: The thickness of each layer in a print.

• Print Speed: How fast the printer moves while extruding filament.

Key Concepts:
This section covers the most common 3D printing parameters, including infill density, layer height, and print speed. Students will learn how adjusting these parameters can affect print quality, strength, and print time.

Challenges:
It can be difficult for students to understand how changes to parameters like layer height impact both print quality and print time. Illustrations showing the difference in print results can help clarify these concepts.

Tips and Tricks:
Lowering the layer height produces finer prints but takes longer. Balancing print speed and quality is key for achieving optimal results.

6. Troubleshooting Setup Issues

New or Complex Vocabulary:

• Warping: When the edges of a print lift off the bed during printing.

• Under-extrusion: When not enough filament is extruded, causing gaps in the print.

Key Concepts:
Troubleshooting is an essential skill in 3D printing. This section outlines common problems such as warping, under-extrusion, and poor adhesion to the print bed. Students will learn how to diagnose and fix these issues.

Challenges:
Understanding the root cause of problems like warping or layer shifting can be tough for beginners. Including a troubleshooting flowchart will simplify the process.

Real-World Applications:
Learning to troubleshoot effectively ensures that students can maintain smooth 3D printing operations in both academic and professional environments.

-------------------------------------

1. Unboxing and Assembling the 3D Printer

Materials Needed:

• 3D printer kit

• Tools (usually included with the printer)

• Power supply

• User manual

Step-by-Step Assembly:

1. Unbox the Printer: Carefully unpack all components. Make sure no parts are missing (refer to the user manual’s parts list).

2. Assemble the Frame: If your printer comes as a kit, follow the instructions to assemble the frame. Use the provided tools to screw together the various components.

3. Mount the Extruder and Hot End: Attach the extruder to the designated spot, ensuring the hot end is securely fitted.

4. Install the Print Bed: Attach the print bed (the surface where prints will be made) to the printer’s frame.

5. Connect Wiring: Follow the wiring diagram in the manual to connect the motor wires, sensor wires, and power supply. Be careful to secure connections to avoid short circuits.

6. Attach Filament Holder: Mount the filament holder at the top or side of the printer (depending on the model).

Tip: Make sure to work in a well-lit, organized space to avoid losing small parts during assembly.

2. Printer Calibration

Calibration ensures your 3D printer works accurately, producing high-quality prints.

Step-by-Step Calibration:

1. Level the Print Bed:

   • Manually adjust the print bed by using the leveling screws located under the bed.

   • Place a piece of paper between the nozzle and the bed and adjust the screws until the paper moves with slight resistance across the surface.

2. Set the Nozzle Height: This is typically done through the printer’s interface. Set the nozzle height so it is the optimal distance from the print bed (just enough to touch the paper).

3. Check Axis Movements: Use the printer's control panel to move the X, Y, and Z axes. Ensure smooth movement without any binding.

4. Adjust the Extruder: Load filament into the extruder and check if the extrusion is smooth. Ensure the filament flows consistently without clogging.

Tip: Regular calibration helps prevent issues like poor adhesion and uneven prints.

3. Loading the Filament

Step-by-Step Guide for Loading Filament:

1. Preheat the Hot End: In the printer’s control panel, navigate to the temperature settings and preheat the extruder (usually around 200°C for PLA filament).

2. Insert the Filament: Once the extruder is heated, insert the filament into the extruder’s filament input, ensuring the filament feeds smoothly into the tube.

3. Extrude a Test Line: Use the "Extrude" function in the printer’s settings to push a small amount of filament through the nozzle to ensure the material flows correctly.

Tip: Different filaments have different ideal temperatures (e.g., ABS around 230°C, PETG around 240°C), so make sure to check before printing.

4. Setting Up the Printer Software (Slicing Software)

To prepare a 3D model for printing, you’ll need to use slicing software like Cura, PrusaSlicer, or Simplify3D. This software converts 3D models into G-code, the language 3D printers understand.

Step-by-Step Software Setup:

1. Download and Install the Software:

   • Download your preferred slicing software (e.g., Cura) from the official website.

   • Install it on your computer.

2. Select Your Printer Model:

   • Open the slicing software and select the correct 3D printer model from the list of supported printers.

3. Configure Printer Settings:

   • Build Volume: Set the dimensions of your printer’s build area.

   • Nozzle Diameter: Typically 0.4mm, but this can vary.

   • Filament Type: Choose the filament you are using (PLA, ABS, PETG, etc.).

   • Heated Bed: If your printer has a heated bed, enable this feature in the settings.

Tip: Start with the default settings recommended for your printer, and gradually tweak them as you gain more experience.

5. Preparing a 3D Model for Printing

Step-by-Step Model Preparation:

1. Import the 3D Model: Open your slicing software and import the 3D model (STL or OBJ file) you want to print.

2. Position the Model on the Bed: Use the software’s interface to move, rotate, or scale the model as needed. Ensure the model fits within the build volume.

3. Configure Print Settings:

   • Layer Height: Determines the quality of the print. Typical layer heights are between 0.1mm (fine) to 0.3mm (fast).

   • Infill Density: Defines how solid the object is (20% infill is typical for non-functional parts).

   • Print Speed: Usually around 50-60 mm/s for PLA; slower speeds are recommended for higher quality prints.

   • Temperature: Set the nozzle temperature based on the filament type (e.g., 200°C for PLA).

4. Add Supports (If Necessary): For models with overhangs, enable support structures in the slicing software. Supports prevent parts from sagging during printing.

5. Slice the Model: Click the Slice button in the software to convert the model into G-code. This file will contain the instructions for your printer.

Tip: Always check the estimated print time after slicing to ensure you have enough time to complete the print.

6. Transferring the G-code to the Printer

Step-by-Step Transfer Process:

1. Save the G-code: After slicing, save the G-code file to an SD card or USB drive.

2. Insert the SD Card/USB Drive into the Printer: Once inserted, use the printer’s interface to select the file you want to print.

3. Start the Print: Choose the Start Print option, and your printer will begin the process of printing the object.

Tip: Make sure the printer is in a well-ventilated area and monitor the first few layers of the print to ensure proper adhesion to the bed.

7. Monitoring the Print

Step-by-Step Monitoring:

1. Check Bed Adhesion: Ensure the first layer is sticking to the print bed without any lifting or curling. If needed, pause the print and adjust the bed or nozzle height.

2. Watch for Common Print Issues: Keep an eye out for issues like stringing, under-extrusion, or layer shifting.

3. Use a Webcam (Optional): If your printer supports it, use a webcam to remotely monitor long prints.

8. Post-Print Finishing

Step-by-Step Post-Processing:

1. Remove the Print: Once the print is complete and the bed has cooled, carefully remove the print using a spatula or print removal tool.

2. Clean Up: If your print used supports, carefully remove them with pliers or cutters. Sand any rough edges for a smooth finish.

Tip: Some prints may benefit from post-processing techniques like sanding, painting, or using acetone vapor (for ABS prints) to smooth the surface.

Typical 3D Printer Parameters

Here are some standard parameters you will configure in your slicing software:

• Layer Height: 0.1mm to 0.3mm (lower values for higher detail).

• Infill Density: 10% to 50% depending on strength needs.

• Print Speed: 50-60 mm/s for PLA (slower for higher quality).

• Nozzle Temperature: 200°C for PLA, 230°C for ABS.

• Bed Temperature: 60°C for PLA, 100°C for ABS.

• Print Bed Adhesion: Use a raft, brim, or glue stick to improve adhesion to the print bed.

By following these steps, you’ll be ready to set up and configure your 3D printer, generate a G-code file, and begin printing successfully. Happy printing!

-----------------------

Here are 10 more typical 3D printer parameters that should be specified for optimal performance and print quality:

1. Retraction Distance:

   • Controls how much filament is pulled back into the nozzle during travel moves to reduce stringing.

   • Typical values: 1mm to 6mm (depending on printer type, direct-drive or Bowden extruder).

2. Retraction Speed:

   • The speed at which the filament is retracted.

   • Typical values: 20 mm/s to 60 mm/s (slower speeds for flexible filaments).

3. Print Cooling Fan Speed:

   • Controls the speed of the cooling fan used to cool the filament after extrusion.

   • Typical values: 100% for PLA, 0-30% for ABS (since it cools slower to prevent warping).

4. Travel Speed:

   • The speed at which the print head moves when not extruding filament.

   • Typical values: 120 mm/s to 200 mm/s.

5. Shell Thickness/Wall Line Count:

   • Defines the number of outer layers (shells) around the object.

   • Typical values: 0.8mm to 1.2mm (equivalent to 2-3 wall lines with a 0.4mm nozzle).

6. First Layer Height:

   • The layer height for the first layer of the print, often set slightly higher for better adhesion.

   • Typical values: 0.2mm to 0.3mm (regardless of overall layer height).

7. First Layer Speed:

   • The speed at which the first layer is printed, often slower for better adhesion.

   • Typical values: 20 mm/s to 30 mm/s.

8. Support Overhang Angle:

   • Specifies the maximum overhang angle (relative to vertical) that will require support structures.

   • Typical values: 45° to 60° (depending on the printer’s capabilities).

9. Top and Bottom Layer Thickness:

   • Controls the thickness of the solid top and bottom layers of the print.

   • Typical values: 0.6mm to 1.0mm (usually equivalent to 3-5 layers).

10. Bridging Speed:

    • The speed at which the printer moves when printing "bridges" (unsupported spans).

    • Typical values: 20 mm/s to 40 mm/s (slower speeds ensure better bridge quality).

By carefully adjusting these parameters in your slicing software, you can optimize print quality for different materials and models.

---------------------------

Here are 10-20 typical parameters that students using UltiMaker Cura software should configure when generating a 3D printer file:

1. Layer Height

• Controls the thickness of each printed layer.

• Typical values: 0.1mm to 0.3mm (smaller layers for finer detail, larger layers for faster prints).

2. Wall Line Count (Shells)

• Defines the number of outer walls printed around each layer.

• Typical values: 2-3 walls.

3. Infill Density

• Controls how solid the interior of the print is.

• Typical values: 10% to 20% for most objects, 50%+ for functional parts.

4. Infill Pattern

• Determines the structure of the internal support (e.g., grid, lines, honeycomb).

• Common patterns: Grid, Triangles, Gyroid, Cubic.

5. Print Speed

• Adjusts how fast the print head moves during extrusion.

• Typical values: 40 mm/s to 60 mm/s for general prints, slower for high-detail prints.

6. Retraction Distance

• How much filament is retracted to prevent oozing during non-print moves.

• Typical values: 4mm to 6mm for Bowden extruders, 1mm to 2mm for direct drive.

7. Retraction Speed

• The speed at which the filament is pulled back during retraction.

• Typical values: 25 mm/s to 40 mm/s.

8. Initial Layer Height

• The height of the first layer, often set larger for better adhesion.

• Typical values: 0.2mm to 0.3mm.

9. Initial Layer Print Speed

• Slower speed for better adhesion of the first layer.

• Typical values: 20 mm/s to 30 mm/s.

10. Build Plate Temperature

• Controls the temperature of the print bed.

• Typical values: 60°C to 70°C for PLA, 90°C to 110°C for ABS.

11. Nozzle Temperature

• Sets the temperature for the hot end that extrudes the filament.

• Typical values: 200°C to 220°C for PLA, 240°C to 260°C for ABS.

12. Cooling Fan Speed

• Controls the cooling fan used to solidify the extruded filament.

• Typical values: 100% for PLA, 0% to 30% for ABS.

13. Support Structure

• Enables or disables support material for overhangs.

• Types: Everywhere, Touching Buildplate.

14. Support Overhang Angle

• Specifies the maximum overhang angle before supports are needed.

• Typical values: 50° to 60°.

15. Build Plate Adhesion Type

• Determines how the model adheres to the bed. Options include Brim, Raft, and Skirt.

• Brim is often used for better bed adhesion.

16. Top/Bottom Layer Thickness

• Adjusts the number of solid layers at the top and bottom of the print.

• Typical values: 0.6mm to 1.2mm.

17. Travel Speed

• Controls how fast the print head moves when not extruding.

• Typical values: 120 mm/s to 200 mm/s.

18. Combing Mode

• Reduces stringing by keeping the nozzle within the printed part during travel moves.

• Typical mode: "Within Infill."

19. Z-Hop When Retracted

• Lifts the nozzle slightly during travel to avoid dragging across the print.

• Typical values: 0.2mm to 0.5mm.

20. Filament Diameter

• Specifies the diameter of the filament used (usually 1.75mm or 2.85mm).

• Ensure it matches the filament loaded in the printer.

By adjusting these parameters correctly in UltiMaker Cura, students can improve print quality, reduce errors, and optimize printing for different materials and models.

------------------------------

Step By Step Getting Started User Guide for Configuring a 3D Printer File

This guide will help you configure a 3D printer file in UltiMaker Cura or similar slicing software. By following these steps, you'll be able to generate a G-code file ready for printing. Along the way, we’ll cover essential 3D printer parameters and G-code settings.

1. Choose Your Printer

Before starting, ensure that Cura is configured to work with your specific 3D printer model.

• Steps:

  1. Open Cura and navigate to the printer settings.

  2. Select your printer model from the list, or add a new printer if it is not available.

  3. Make sure that the build volume, nozzle size, and other hardware configurations are correct for your printer.

2. Import Your 3D Model

• Steps:

  1. Click on "Open File" and select your 3D model file (.STL, .OBJ, etc.).

  2. The model will appear on the virtual build plate.

3. Orient and Position the Model

• Steps:

  1. Rotate and scale your model as needed using the built-in tools to ensure it fits within the print volume.

  2. Check that the model is positioned flat on the build plate.

4. Set Layer Height (Resolution)

The layer height affects both print quality and speed.

• Steps:

  1. Go to the Layer Height setting.

  2. For fine details, choose a smaller layer height (e.g., 0.1mm).

  3. For quicker prints, select a larger layer height (e.g., 0.2mm to 0.3mm).

5. Set Infill Density and Pattern

Infill provides internal support for your model.

• Steps:

  1. Choose the Infill Density (10-20% for most prints, higher for stronger parts).

  2. Select the Infill Pattern (e.g., Grid, Gyroid, or Triangles) based on strength and material savings.

6. Configure Wall/Shell Thickness

The outer walls (shells) give your print its surface strength and finish.

• Steps:

  1. Set Wall Line Count (typically 2-3 walls).

  2. Alternatively, specify the Wall Thickness directly (e.g., 0.8mm to 1.2mm).

7. Adjust Print Speed

Printing speed impacts quality and time.

• Steps:

  1. Choose Print Speed (40 mm/s to 60 mm/s for most prints).

  2. For intricate or detailed models, consider lowering the speed (30 mm/s).

8. Set Retraction Settings

Retraction settings help reduce stringing (unwanted filament between parts).

• Steps:

  1. Set Retraction Distance (4mm to 6mm for Bowden extruders, 1mm to 2mm for direct-drive extruders).

  2. Set Retraction Speed (25 mm/s to 40 mm/s).

9. Configure Build Plate Adhesion

Ensure the model sticks to the bed during the print.

• Steps:

  1. Select Build Plate Adhesion Type (Brim or Raft are common for better adhesion).

  2. Adjust the settings depending on the object size (Brim width, Raft layers, etc.).

10. Set Nozzle and Bed Temperature

Different filaments require specific temperatures.

• Steps:

  1. Set Nozzle Temperature (200°C to 220°C for PLA, 240°C to 260°C for ABS).

  2. Set Build Plate Temperature (60°C to 70°C for PLA, 90°C to 110°C for ABS).

11. Cooling Fan Speed

Cooling is essential for some materials.

• Steps:

  1. Set the Cooling Fan Speed (100% for PLA, 0% to 30% for ABS).

12. Enable Support Structures

Supports are necessary for overhangs and complex geometries.

• Steps:

  1. Enable Support Structures if your model has overhangs.

  2. Set the Support Overhang Angle (45° to 60°).

13. Adjust Initial Layer Settings

The first layer is critical for bed adhesion.

• Steps:

  1. Set Initial Layer Height slightly larger than the rest (e.g., 0.2mm to 0.3mm).

  2. Lower the Initial Layer Speed (20 mm/s to 30 mm/s) for better adhesion.

14. Review Other Parameters

Other settings can be critical depending on the print.

• Steps:

  1. Check Z-Hop When Retracted to avoid the nozzle dragging across the print.

  2. Set Travel Speed to prevent blobs or stringing (120 mm/s to 200 mm/s).

15. Generate G-code

Once the settings are configured, generate the G-code for your 3D printer.

• Steps:

  1. Click Slice to convert your 3D model into G-code.

  2. Preview the sliced model to check layer lines and any potential issues.

  3. Save the G-code to an SD card or transfer it directly to your printer if connected.

Typical 3D Printer Parameters to Set in Cura:

• Layer Height: 0.1mm to 0.3mm

• Wall Line Count: 2-3 walls

• Infill Density: 10% to 20%

• Infill Pattern: Grid, Gyroid, Triangles

• Print Speed: 40 mm/s to 60 mm/s

• Retraction Distance: 4mm to 6mm

• Retraction Speed: 25 mm/s to 40 mm/s

• Nozzle Temperature: 200°C to 220°C for PLA

• Bed Temperature: 60°C to 70°C for PLA

• Cooling Fan Speed: 100% for PLA

• Support Structures: Enabled if needed

• Build Plate Adhesion Type: Brim or Raft

Final Steps

With all the settings configured, you're ready to load your G-code into the 3D printer and start printing! Ensure you monitor the first few layers to verify proper adhesion and print quality.

Reference, Attribution & Resources:

Resource Attribution:
Sites Referenced or Summarized:

• Reference Text Book - 

• Reference Sites - 

Images:

• https://imgbin.com/png/ZJtzkYZZ/under-construction-png

• 
  

Random Stuff To Sort

Resource Key:

<Unit> - <Module Name> - Lessons - Daily/Weekly Lesson Plan

Key: 📰 Slides / Audio 🎧 / 📽️▶️ Video/YouTube / 🎧▶️📽️ Audio/Video / ✨ Resources /  🖼️ Tutorial / 📖 Reading Activity / 📝 Writing Activity / 📖 📝 Reading/Writing / 📟 Coding / 🛠️ LAB Activity / 🚀 Quiz /  🔎 Review /  ✔️ Mastery Check / ✍️ Sign Up /🍕 Extra Credit / 🕸️ Web Links / 👩🏽‍🎓🧑🏽‍🎓🧑🏿‍🎓👩‍🏫 Class / 🏵️📜📃 Certificate / 🗂️ 📈 Collecting Survey Data

/🧟 Review / 🦾 Practice / 🆙Level Up /

🎚️🦑📤🎯  🚧

- 🦑 Special Project -

Assignment Type: ⚓ Establishing (Minimum Standard) / ⛏️ Developing (Digging Deeper) / 💎 Aspiring (Putting It Together)

This is an ⚓ Establishing Assignment (Minimum Standard)  - "Everyone Do" Assignment

This is an ⛏️ Developing (Digging Deeper) - "Everyone Should Do, To Stretch" Assignment

This is an 💎 Aspiring (Putting It Together)  - "When you have done the ⚓ Establishing and⛏️ Developing" Assignment

• 🚀 Formative Quiz - 🔎 Review

• 🚀 Quiz -🔀 Mastery Path

• 🚀 Summative Quiz -✔️ Skills Mastery Check

Quiz - verify that they are all listed as a "Formative", "Mastery Path", or "Summative" 

• 🚀 Formative Quiz - These are quizzes that the students can take a few times. I have them either set for unlimited times, or 3-5 times, where the final score is their average. The idea is that these Formative Quizzes are designed for students to learn and master a skill.  while I want them to ger 100%, and when it's set to unlimited tries, the student should get 100% eventually.  When the quiz is set to 3-5 tries with an average, then they should be prepared and should take the quiz seriously. I set the quiz to not show the right answer, but I do let them see their wrong answer.  I also put the explanation of the right and wrong answer in the right and wrong answer prompt for each question.  That way they can see why they got the answer wrong and learn from that experience.  

  • 8.1.0.3.2.4 - Python - Ch 3 - Functions - Quiz #2 -Built-In Functions - 🚀 Formative Quiz

• 🚀 Quiz -🔀 Mastery Path - These Mastery path quizzes are to be presented after the student has had a chance to do some labs and some Formative quizzes.   The goal is to let students have 2 chances to take this quiz, and take the average of the 2 attempts.  Based on the average, they will be presented with a Canvas Mastery Path, where they will have an option for take additional quiz and assignments to help with remediation.  This will get them ready to take the Summative Quizzes.

  • 8.1.0.3.3.1 -  Python - Ch 3 - Functions - Mastery Quiz #1 - 🚀 Quiz -🔀 Mastery Path

• 🚀 Summative Quiz -✔️ Skills Mastery Check - These Mastery path quizzes are to be presented after the student has had a chance to do some labs and some Formative quizzes.   The goal is to let students have 2 chances to take this quiz, and take the average of the 2 attempts. That will be their final module/subject topic grade.

  • 8.1.0.3.3.1 -  Python - Ch 3 - Functions - Skills Mastery Check Quiz #1 - 🚀 Summative Quiz -✔️ Skills Mastery Check