Embedded Files
ST7735 TFT 液晶顯示器介紹<檔案位置>
ST7735 TFT全彩LCD ，1.44吋：128x128，1.8吋：120x160。
使用
電源使用：3.3V
I2C 掃描程式
//使用ESP32 第21、22腳，先偵測所使用的I2C設備編號
#include <Wire.h>
void setup()
{
Serial.begin (115200);
Wire.begin (21, 22); // sda= GPIO_21 /scl= GPIO_22
}
void Scanner ()
{
Serial.println ();
Serial.println ("I2C scanner. Scanning ...");
byte count = 0;
Wire.begin();
for (byte i = 8; i < 120; i++)
{
Wire.beginTransmission (i); // Begin I2C transmission Address (i)
if (Wire.endTransmission () == 0) //0=success(ACK response)
{
Serial.print ("Found address: ");
Serial.print (i, DEC);
Serial.print (" (0x");
Serial.print (i, HEX); // PCF8574 7 bit address
Serial.println (")");
count++;
}
}
Serial.print ("Found ");
Serial.print (count, DEC); // numbers of devices
Serial.println (" device(s).");
}
void loop()
{
Scanner ();
delay (5000);
如序列視窗所示，I2C 偵測的裝置位置為 0x30
ssd 1306 OLED顯示測試(OLED_HELLO.ino)
#include<Wire.h>
#include<Adafruit_GFX.h>
#include<Adafruit_SSD1306.h>
#define CREEN_WIDTH 128 //設定OLED螢幕的寬度像素
#define CREEN_HEIGHT 64 //設定OLED螢幕的寬度像素
#define OLED_RESET -1 //Reset pin如果OLED上沒有RESET腳位,將它設置為-1
Adafruit_SSD1306 display(CREEN_WIDTH, CREEN_HEIGHT, &Wire, OLED_RESET); //OLED顯示器使用2C連線並宣告名為display物件
bool OLEDStatus = true;
void setup() {
Serial.begin(115200);
if(!display.begin(SSD1306_SWITCHCAPVCC,0x3C)) { //設定位址為 0x3c
Serial.println(F("SSD1306 allocation falled")); //F(字串):將字串儲存在fash並非在RAM
OLEDStatus = false; //開啟OLED失敗
}
if(OLEDStatus == true)
testdrawchar(); //Draw characters of the default font
}
void loop() {
}
void testdrawchar(void) {
display.clearDisplay(); //清除緩衝區資料
display.setTextSize(1); //設定文字尺寸為1,1:6x8,2:12x16,3:18x24...etc
display.setCursor(0, 0); //設定起始點位置(0,0)
display.setTextColor(BLACK, WHITE); //黑字白底
display.println("Hello") ; //將"Hello"存入RAM
display.setCursor(0,16); //設定起始點位置(0,16)
display.setTextSize(2); //設定文字尺寸為2
display.setTextColor(WHITE); //設定文字顏色為白色(亮點)
display.println("Hello"); //將"Hello"存入RAM
display.setTextSize(3); //設定文字尺寸為3
display.println("Hello"); //將"Hello"存入RAM
display.display(); //顯示所設定文字
}
連上網路顯示日期與時間
//OLED_time 上網讀取時間
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
#include <WiFi.h>
#include "time.h"
#define CREEN_WIDTH 128 //設定OLED螢幕的寬度像素
#define CREEN_HEIGHT 64 //設定OLED螢幕的寬度像素
#define OLED_RESET -1 //Reset pin如果OLED上沒有RESET腳位,將它設置為-1
Adafruit_SSD1306 display(CREEN_WIDTH, CREEN_HEIGHT, &Wire, OLED_RESET); //OLED顯示器使用2C連線並宣告名為display物件
const char* ssid = "AX"; //連線名稱
const char* password ="CPSHScpshs"; //連線密碼
const char* ntpServer = "pool.ntp.org"; //NTP Server網址
const long gmtOffset_sec =28800; //台灣為GMT8小时·8hrs=28800sec
const int daylightOffset_sec= 0; //日光節時間為0
bool OLEDStatus = true;
static const unsigned char PROGMEM str_1[]={ //現
0x00,0x08,0x01,0xFC,0xFD,0x08,0x11,0x08,0x11,0xF8,0x11,0x08,0x11,0x08,0x7D,0xF8,
0x11,0x08,0x11,0x08,0x11,0xF8,0x1D,0x48,0xF0,0xA0,0x41,0x22,0x02,0x22,0x0C,0x1E
};
static const unsigned char PROGMEM str_2[]={ //在
0x02,0x00,0x02,0x00,0x02,0x04,0xFF,0xFE,0x04,0x00,0x04,0x40,0x08,0x40,0x08,0x48,
0x13,0xFC,0x30,0x40,0x50,0x40,0x90,0x40,0x10,0x40,0x10,0x44,0x17,0xFE,0x10,0x00
};
static const unsigned char PROGMEM str_3[]={ //時
0x00,0x20,0x04,0x20,0x7E,0xF8,0x44,0x20,0x44,0x20,0x45,0xFC,0x44,0x10,0x7C,0x10,
0x47,0xFE,0x44,0x10,0x44,0x90,0x44,0x50,0x7C,0x50,0x44,0x10,0x00,0x50,0x00,0x20
};
static const unsigned char PROGMEM str_4[]={ //間
0x00,0x08,0x7C,0xFC,0x44,0x88,0x7C,0xF8,0x44,0x88,0x7C,0xF8,0x40,0x08,0x4F,0xC8,
0x48,0x48,0x4F,0xC8,0x48,0x48,0x4F,0xC8,0x48,0x48,0x40,0x08,0x40,0x28,0x40,0x10
};
void setup() {
Serial.begin(9600);
if(!display.begin(SSD1306_SWITCHCAPVCC,0x3c)) { //設定位址為 0x3c
Serial.println(F("SSD1306 allocation falled")); //F(字串):將字串儲存在fash並非在RAM
OLEDStatus = false; //開啟OLED失敗
}
Serial.printf("Connecting to %s ", ssid); //顯示連線AP SSID
WiFi.begin(ssid, password); //建立WiFi連線
while (WiFi.status() != WL_CONNECTED) { //當狀態不是已連線
Serial.print("."); //印出一個"."
}
Serial.println(" CONNECTED"); //初始化並取回時間
configTime(gmtOffset_sec, daylightOffset_sec, ntpServer); //設定NTP參數
}
void loop() {
struct tm timeinfo; //建立一個時間結構,為timeinfo
if(!getLocalTime(&timeinfo)){ //取回NTP時間
Serial.println("Failedto obtain time"); //若失敗，顯示失敗訊息"
return;
}
Serial.println(&timeinfo, "%A, %B %d %Y %H:%M:%S"); //顯示"星期,月日年,時:分:秒
if(OLEDStatus==true) {
display.clearDisplay(); //清除緩衝區資料
display.setTextSize(2); //設定字型大小為2
display.setCursor(4,0); //設定文字起始位置為(4,0)
display.setTextColor(WHITE, BLACK); //設定白字黑底
display.println(&timeinfo, "%F"); //設定文字内容為年月日,格式為"西元年-月-日"
display.setCursor(10,16); //設定文字起始位置為(10,16)
display.println(&timeinfo, "%A"); //設定文字内容為星期,格式為Mondy Tu·
display.drawBitmap(0, 32, str_1, 16, 16, WHITE); //現,位置( 0,32)字型大小16*16顏色白色
display.drawBitmap(18, 32, str_2, 16, 16, WHITE); //在,位置(18,32)字型大小16*16顏色白色
display.drawBitmap(36, 32, str_3, 16, 16, WHITE); //時,位置(36,32),字型大小16*16顏色自色
display.drawBitmap(54, 32, str_4, 16, 16, WHITE); //間,位置(54,32),字型大小16*16,顏色白色
display.setCursor(16,50); //設定文字起始位置為(16,48)
display.println(&timeinfo, "%T"); //設定文字內容為年月日,格式為"時:分:秒"
display.display(); //顯示所設定的文字
}
delay(1000);
}
其他功能展示
動畫功能展示
//SSD1306_128*64_DEMO
/**************************************************************************
This is an example for our Monochrome OLEDs based on SSD1306 drivers
Pick one up today in the adafruit shop!
------> http://www.adafruit.com/category/63_98
This example is for a 128x64 pixel display using I2C to communicate
3 pins are required to interface (two I2C and one reset).
Adafruit invests time and resources providing this open
source code, please support Adafruit and open-source
hardware by purchasing products from Adafruit!
Written by Limor Fried/Ladyada for Adafruit Industries,
with contributions from the open source community.
BSD license, check license.txt for more information
All text above, and the splash screen below must be
included in any redistribution.
**************************************************************************/
#include <SPI.h>
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
#define SCREEN_WIDTH 128 // OLED display width, in pixels
#define SCREEN_HEIGHT 64 // OLED display height, in pixels
// Declaration for an SSD1306 display connected to I2C (SDA, SCL pins)
// The pins for I2C are defined by the Wire-library.
// On an arduino UNO: A4(SDA), A5(SCL)
// On an arduino MEGA 2560: 20(SDA), 21(SCL)
// On an arduino LEONARDO: 2(SDA), 3(SCL), ...
#define OLED_RESET -1 // Reset pin # (or -1 if sharing Arduino reset pin)
#define SCREEN_ADDRESS 0x3C ///< See datasheet for Address; 0x3D for 128x64, 0x3C for 128x32
Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, OLED_RESET);
#define NUMFLAKES 10 // Number of snowflakes in the animation example
#define LOGO_HEIGHT 16
#define LOGO_WIDTH 16
static const unsigned char PROGMEM logo_bmp[] =
{ 0b00000000, 0b11000000,
0b00000001, 0b11000000,
0b00000001, 0b11000000,
0b00000011, 0b11100000,
0b11110011, 0b11100000,
0b11111110, 0b11111000,
0b01111110, 0b11111111,
0b00110011, 0b10011111,
0b00011111, 0b11111100,
0b00001101, 0b01110000,
0b00011011, 0b10100000,
0b00111111, 0b11100000,
0b00111111, 0b11110000,
0b01111100, 0b11110000,
0b01110000, 0b01110000,
0b00000000, 0b00110000 };
void setup() {
Serial.begin(9600);
// SSD1306_SWITCHCAPVCC = generate display voltage from 3.3V internally
if(!display.begin(SSD1306_SWITCHCAPVCC, SCREEN_ADDRESS)) {
Serial.println(F("SSD1306 allocation failed"));
for(;;); // Don't proceed, loop forever
}
// Show initial display buffer contents on the screen --
// the library initializes this with an Adafruit splash screen.
display.display();
delay(2000); // Pause for 2 seconds
// Clear the buffer
display.clearDisplay();
// Draw a single pixel in white
display.drawPixel(10, 10, SSD1306_WHITE);
// Show the display buffer on the screen. You MUST call display() after
// drawing commands to make them visible on screen!
display.display();
delay(2000);
// display.display() is NOT necessary after every single drawing command,
// unless that's what you want...rather, you can batch up a bunch of
// drawing operations and then update the screen all at once by calling
// display.display(). These examples demonstrate both approaches...
testdrawline(); // Draw many lines
testdrawrect(); // Draw rectangles (outlines)
testfillrect(); // Draw rectangles (filled)
testdrawcircle(); // Draw circles (outlines)
testfillcircle(); // Draw circles (filled)
testdrawroundrect(); // Draw rounded rectangles (outlines)
testfillroundrect(); // Draw rounded rectangles (filled)
testdrawtriangle(); // Draw triangles (outlines)
testfilltriangle(); // Draw triangles (filled)
testdrawchar(); // Draw characters of the default font
testdrawstyles(); // Draw 'stylized' characters
testscrolltext(); // Draw scrolling text
testdrawbitmap(); // Draw a small bitmap image
// Invert and restore display, pausing in-between
display.invertDisplay(true);
delay(1000);
display.invertDisplay(false);
delay(1000);
testanimate(logo_bmp, LOGO_WIDTH, LOGO_HEIGHT); // Animate bitmaps
}
void loop() {
}
void testdrawline() {
int16_t i;
display.clearDisplay(); // Clear display buffer
for(i=0; i<display.width(); i+=4) {
display.drawLine(0, 0, i, display.height()-1, SSD1306_WHITE);
display.display(); // Update screen with each newly-drawn line
delay(1);
}
for(i=0; i<display.height(); i+=4) {
display.drawLine(0, 0, display.width()-1, i, SSD1306_WHITE);
display.display();
delay(1);
}
delay(250);
display.clearDisplay();
for(i=0; i<display.width(); i+=4) {
display.drawLine(0, display.height()-1, i, 0, SSD1306_WHITE);
display.display();
delay(1);
}
for(i=display.height()-1; i>=0; i-=4) {
display.drawLine(0, display.height()-1, display.width()-1, i, SSD1306_WHITE);
display.display();
delay(1);
}
delay(250);
display.clearDisplay();
for(i=display.width()-1; i>=0; i-=4) {
display.drawLine(display.width()-1, display.height()-1, i, 0, SSD1306_WHITE);
display.display();
delay(1);
}
for(i=display.height()-1; i>=0; i-=4) {
display.drawLine(display.width()-1, display.height()-1, 0, i, SSD1306_WHITE);
display.display();
delay(1);
}
delay(250);
display.clearDisplay();
for(i=0; i<display.height(); i+=4) {
display.drawLine(display.width()-1, 0, 0, i, SSD1306_WHITE);
display.display();
delay(1);
}
for(i=0; i<display.width(); i+=4) {
display.drawLine(display.width()-1, 0, i, display.height()-1, SSD1306_WHITE);
display.display();
delay(1);
}
delay(2000); // Pause for 2 seconds
}
void testdrawrect(void) {
display.clearDisplay();
for(int16_t i=0; i<display.height()/2; i+=2) {
display.drawRect(i, i, display.width()-2*i, display.height()-2*i, SSD1306_WHITE);
display.display(); // Update screen with each newly-drawn rectangle
delay(1);
}
delay(2000);
}
void testfillrect(void) {
display.clearDisplay();
for(int16_t i=0; i<display.height()/2; i+=3) {
// The INVERSE color is used so rectangles alternate white/black
display.fillRect(i, i, display.width()-i*2, display.height()-i*2, SSD1306_INVERSE);
display.display(); // Update screen with each newly-drawn rectangle
delay(1);
}
delay(2000);
}
void testdrawcircle(void) {
display.clearDisplay();
for(int16_t i=0; i<max(display.width(),display.height())/2; i+=2) {
display.drawCircle(display.width()/2, display.height()/2, i, SSD1306_WHITE);
display.display();
delay(1);
}
delay(2000);
}
void testfillcircle(void) {
display.clearDisplay();
for(int16_t i=max(display.width(),display.height())/2; i>0; i-=3) {
// The INVERSE color is used so circles alternate white/black
display.fillCircle(display.width() / 2, display.height() / 2, i, SSD1306_INVERSE);
display.display(); // Update screen with each newly-drawn circle
delay(1);
}
delay(2000);
}
void testdrawroundrect(void) {
display.clearDisplay();
for(int16_t i=0; i<display.height()/2-2; i+=2) {
display.drawRoundRect(i, i, display.width()-2*i, display.height()-2*i,
display.height()/4, SSD1306_WHITE);
display.display();
delay(1);
}
delay(2000);
}
void testfillroundrect(void) {
display.clearDisplay();
for(int16_t i=0; i<display.height()/2-2; i+=2) {
// The INVERSE color is used so round-rects alternate white/black
display.fillRoundRect(i, i, display.width()-2*i, display.height()-2*i,
display.height()/4, SSD1306_INVERSE);
display.display();
delay(1);
}
delay(2000);
}
void testdrawtriangle(void) {
display.clearDisplay();
for(int16_t i=0; i<max(display.width(),display.height())/2; i+=5) {
display.drawTriangle(
display.width()/2 , display.height()/2-i,
display.width()/2-i, display.height()/2+i,
display.width()/2+i, display.height()/2+i, SSD1306_WHITE);
display.display();
delay(1);
}
delay(2000);
}
void testfilltriangle(void) {
display.clearDisplay();
for(int16_t i=max(display.width(),display.height())/2; i>0; i-=5) {
// The INVERSE color is used so triangles alternate white/black
display.fillTriangle(
display.width()/2 , display.height()/2-i,
display.width()/2-i, display.height()/2+i,
display.width()/2+i, display.height()/2+i, SSD1306_INVERSE);
display.display();
delay(1);
}
delay(2000);
}
void testdrawchar(void) {
display.clearDisplay();
display.setTextSize(1); // Normal 1:1 pixel scale
display.setTextColor(SSD1306_WHITE); // Draw white text
display.setCursor(0, 0); // Start at top-left corner
display.cp437(true); // Use full 256 char 'Code Page 437' font
// Not all the characters will fit on the display. This is normal.
// Library will draw what it can and the rest will be clipped.
for(int16_t i=0; i<256; i++) {
if(i == '\n') display.write(' ');
else display.write(i);
}
display.display();
delay(2000);
}
void testdrawstyles(void) {
display.clearDisplay();
display.setTextSize(1); // Normal 1:1 pixel scale
display.setTextColor(SSD1306_WHITE); // Draw white text
display.setCursor(0,0); // Start at top-left corner
display.println(F("Hello, world!"));
display.setTextColor(SSD1306_BLACK, SSD1306_WHITE); // Draw 'inverse' text
display.println(3.141592);
display.setTextSize(2); // Draw 2X-scale text
display.setTextColor(SSD1306_WHITE);
display.print(F("0x")); display.println(0xDEADBEEF, HEX);
display.display();
delay(2000);
}
void testscrolltext(void) {
display.clearDisplay();
display.setTextSize(2); // Draw 2X-scale text
display.setTextColor(SSD1306_WHITE);
display.setCursor(10, 0);
display.println(F("scroll"));
display.display(); // Show initial text
delay(100);
// Scroll in various directions, pausing in-between:
display.startscrollright(0x00, 0x0F);
delay(2000);
display.stopscroll();
delay(1000);
display.startscrollleft(0x00, 0x0F);
delay(2000);
display.stopscroll();
delay(1000);
display.startscrolldiagright(0x00, 0x07);
delay(2000);
display.startscrolldiagleft(0x00, 0x07);
delay(2000);
display.stopscroll();
delay(1000);
}
void testdrawbitmap(void) {
display.clearDisplay();
display.drawBitmap(
(display.width() - LOGO_WIDTH ) / 2,
(display.height() - LOGO_HEIGHT) / 2,
logo_bmp, LOGO_WIDTH, LOGO_HEIGHT, 1);
display.display();
delay(1000);
}
#define XPOS 0 // Indexes into the 'icons' array in function below
#define YPOS 1
#define DELTAY 2
void testanimate(const uint8_t *bitmap, uint8_t w, uint8_t h) {
int8_t f, icons[NUMFLAKES][3];
// Initialize 'snowflake' positions
for(f=0; f< NUMFLAKES; f++) {
icons[f][XPOS] = random(1 - LOGO_WIDTH, display.width());
icons[f][YPOS] = -LOGO_HEIGHT;
icons[f][DELTAY] = random(1, 6);
Serial.print(F("x: "));
Serial.print(icons[f][XPOS], DEC);
Serial.print(F(" y: "));
Serial.print(icons[f][YPOS], DEC);
Serial.print(F(" dy: "));
Serial.println(icons[f][DELTAY], DEC);
}
for(;;) { // Loop forever...
display.clearDisplay(); // Clear the display buffer
// Draw each snowflake:
for(f=0; f< NUMFLAKES; f++) {
display.drawBitmap(icons[f][XPOS], icons[f][YPOS], bitmap, w, h, SSD1306_WHITE);
}
display.display(); // Show the display buffer on the screen
delay(200); // Pause for 1/10 second
// Then update coordinates of each flake...
for(f=0; f< NUMFLAKES; f++) {
icons[f][YPOS] += icons[f][DELTAY];
// If snowflake is off the bottom of the screen...
if (icons[f][YPOS] >= display.height()) {
// Reinitialize to a random position, just off the top
icons[f][XPOS] = random(1 - LOGO_WIDTH, display.width());
icons[f][YPOS] = -LOGO_HEIGHT;
icons[f][DELTAY] = random(1, 6);
}
}
}
}
相關應用
Page updated
Report abuse