Embedded Files
A.B.=錨定螺栓 (ANCHOR BOLT)
APPROX.=近似 (APPROXIMATE)
AR.=建築 (ARCHITECTURE)
B.C.D.=螺栓位置圓直徑 (BOLT CIRCLE DIAMETER)
BM=梁 (BEAM)
B.O.BASE PL=底板底部 (BOTTOM OF BASE PLATE)
B.O.FTG=基腳底部 (BOTTOM OF FOOTING)
BOT EL=底面高程 (BOTTOM ELEVATION)
BS=兩側 (BOTH SIDE)
CB=集水井 (CATCH BASIN)
C/C=中心到中心 (CENTER TO CENTER)
CHKD PL=花紋鋼板 (CHECKERED PLATE)
CI=鑄鐵 (CAST IRON)
CJ=施工縫 (CONSTRUCTION JOINT)
CL=淨間距, 保護層 (CLEARANCE)
COL=柱 (COLUMN)
CONC=混凝土 (CONCRETE)
CSP=碳鋼管 (CARBON STEEL PIPE)
DIA=直徑 (DIAMETER)
DIM=尺寸 (DIMENSION)
DN=向下 (DOWN)
DWG=圖 (DRAWING)
DO=同上, 相似物 (DITTO)
EF=每面 (EACH FACE)
EJ=伸縮縫 (EXPANSION JOINT)
EL=高程, 高度 (ELEVATION, HEIGHT)
ELEV=立面圖 (ELEVATION, VIEW)
EMB PL=預埋鋼板 (EMBEDDED PLATE)
EQ=相等 (EQUIVALENT)
EW=每向 (EACH WAY)
FDN=基礎 (FOUNDATION)
FFL=地坪完成面高程 (FINISH FLOOR LEVEL)
FTG=基腳 (FOOTING)
FS=遠側 (FAR SIDE)
GL=地面高程 (GROUND LEVEL)
HORIZ=水平 (HORIZONTAL)
HP EL=高點高程 (HIGH POINT ELEVATION)
HPFP=舖面完成高點 (HIGH POINT FINISHED PAVING)
ID=內徑 (INNER DIA METER)
IE OR INV EL=進水或出水高程 (INVERT ELEVATION)
INT=內部 (INTERIOR)
LP EL=低點高程 (LOW POINT ELEVATION)
MH=人孔 (MANHOLE)
MAX=最大 (MAXIMUM)
MIN=最小 (MINIMUM)
NO=數量 (NUMBER)
NTS=不按比例 (NOT TO SCALE)
NS=近側 (NEAR SIDE)
OD=外徑 (OUTSIDE DIAMETER)
OPNG=開孔 (OPENING)
PC=純混凝土 (PLAIN CONCRETE)
P.C.D.=樁位置圓直徑 (PILE CIRCLE DIAMETER)
P.C.O.EL.=樁截斷面高程 (PILE CUT OFF ELEVATION)
PROJ=突出長 (PROJECTION)
P/R=管架 (PIPE RACK)
R=半徑 (RADIUS)
REINF=鋼筋 (REINFORCEMENT)
REQD=需要 (REQUIRED)
SFL=結構樓版高程 (STRUCTURAL FLOOR LEVEL)
SQ=正方型 (SQUARE)
THK=厚度 (THICKNESS)
T.O.G=灌漿頂部 (TOP OF GROUT)
T.O.S=鋼板頂部 (TOP OF STEEL)
T.O.C=混凝土頂部 (TOP OF CONCRETE)
TYP=典型, 代表性 (TYPICAL)
T&B=頂部及底部 (TOP & BOTTOM)
UP=向上 (UP)
VAR=變化的 (VARIOUS)
VB=閘閥箱 (VALVE BOX)
VERT=垂直 (VERTICAL)
W/ =含 (WITH)
W/O =不含 (WITHOUT)
@ =間距 (AT)
& =和, 及 (AND)
CL=中心線 (CENTER LINE)
PL=鋼板, 板 (PLATE)
Google Sites
Report abuse