last update: 2012/02/05
Now Update complete!
The previous manual is under these.
---- New Manual (This applies to version 1.45 or later.)----
A. Double-tap a waypoint pin, then, the lamp will be lit
on that pin.
The order of that pin will be changed to the order of
before one, and the blue line of the route will be
changed.
If that pin still is out the pathway, will be added to the
end of the route.
B. Long-press a waypoint pin continuously, you can
see the [Acknowledged long-press] at upper of
screen. After that, release your finger from the
screen. The lamp will be lit on that pin.
The order of that pin will be changed to the order of
after one, and the blue line of the route will be
changed.
If that pin still is out the pathway, will be
nothing.
C. Tutorial
If there still is no pins within the pathway, first
double-tap a waypoint pin, the lamp only will be lit on
that pin, but the blue line of the route can not be
seen. The number of route of that pin is the first.
Continue, please double-tap another waypoint pin,
then you will be able to see the blue line of the route.
---- New Manual (This applies to version 1.44 or later.)----
A. Turn on new waypoint.
1.Tap on map -> Red pushpin is displayed.
(If you want to place pushpin at the current
position,
Please tap [Here]. Take some time until you see
pushpin. This is to improve accuracy.)
2.Tap [on] button -> Dialog is displayed.
3.Select pin in spinner
-> Selected pin name is displayed.
4.Enter Altitude.
5.Enter Cylinder Radius.
6.Tap [on] button in dialog. -> dialog disappear
and appear new waypoint on map.
B. Turn off existing waypoint.
1.Select pin in spinner
Single tap the way point pin
-> Dialog is displayed.
(if dialog is not displayed, Once, after you select
a different existing pin, again, please select the
desired pin.)
2.Tap [off] button in dialog -> Dialog disappear
and disappear the selected waypoint on map.
C. Change the location of existing waypoint.
(this is same as A.Turn on new waypoint.)
1.Tap on map -> Pushpin is displayed.
2.Tap [on] button -> Dialog is displayed.
3.Select the pin in question in spinner
-> Selected pin name is displayed.
4.Update Altitude, if you need.
5.Update Cylinder Radius, if you need.
6.Tap [on] button in dialog. -> dialog disappear
and appear waypoint on changed location.
D. Change the altitude or the Cylinder Radius of
existing waypoint.
1.Select pin in spinner
Single tap the way point pin -> Dialog is displayed.
(if dialog is not displayed, Once, after you select
a different existing pin, again, please select the
desired pin.)
2.Update Altitude.
3.Update Cylinder Radius.
4.Tap [update] button in dialog -> Dialog disappear.
E. If you know the distance and/or the angle
between two points, select pin in spinner single tap
the way point pin. The distance and
the angle is displayed in dialog. That is between
the last selected single taped pin and that of
previously selected single taped.
(if dialog is not displayed, Once, after you select
a different existing pin,
again, please select the desired pin.)
F. Change the Home Ground.
1.Tap on map or Tap [Here]
-> Red pushpin is displayed.
2.Click [menu] key.
3.Tap [Home Ground] -> Dialog is displayed.
4.Update altitude above sea level.
5.Tap [Ok] -> Dialog disappear
and green [B] pin appear on map.
G. Change the Radius of Approach Circle.
1.Click [menu] key.
2.Tap [Approach Circle] -> Dialog is displayed.
3.Update the Radius of Approach Circle.
4.Tap [Ok] -> Dialog disappear and it is changed.
H. Change the Geoid Altitude.
1.Click [menu] key.
2.Tap [Geoid Altitude] -> Dialog is displayed.
3.Update the Geoid Altitude.
4.Tap [Ok] -> Dialog disappear and it is changed.
I. Display this manual.
1.Click [menu] key.
2.Tap [Help] -> this manual is displayed.
---- previous manual (This applies to version 1.40 or before.)-----
[ menu key ] -> [ planning ]
-> [ The second set of buttons ]
-> [ Pointing ] -> the following screen
First, the pin you want, select it from the spinner.
And tap the desired location on the map.
You will then see a red pushpins and latitude, longitude (numeric data).
Please enter altitude(m), if you want.
CylR is the radius(m) of cylinder circle around the pin. It will be indicated by a red circle around a waypoint.
In the main screen, when GPS measured three values inside the cylinder, the application is judged to be passing through this pin.
Please enter this as you like, if you want.
Finally, when you click [on]button, the pin as waypoint are entered. A red pushpins is changed to display as a waypoint. Conversely [off] button is to cancel the entrants.
Repeat above.
Place all of the waypoints easily.
It is also possible to give a remark for each waypoints, if you want.
Other buttons description.
[map][photo]: map or photo toggle switch.
[Here]:The red pushpins will be placed at your current
position.
[AJ]: Shows the area around your home. (You decide
home at [setting].)
[J]: Displays around the red push pin.
[-]: Zoom out.
[+]: Zoom in.
By using arrow buttons and the zoom button, you will be able to set down a red pushpinsposition in detail.