Do's

Keep your hands away from the saw at all times 

always turn of the saw once done using  

Don't

Horse play around the saw 

don't put your hand too close to the blade while on 

raise the  blade protector to high  

When using a band saw you need to wear safety glasses . When the band saw is on you need to keep your hands away from the saw . When you are done cutting you should turn it off and then unplug the saw. 

Dos

When using a planer saw always keep hands on the side of the machine away from the saws 

always lock the saw before putting wood trough  

c

 Do's

Keep your hand behind the  lines 

always unplug after use 

Don't 

put your had near blade 

put hand on protector 

I used some wood glue to  put both  wood pieces together  using  clamps   

 I used the miter saw to cut a small pieces of wood off . I did this because  they needed to be even 

Do's Don'ts 

Do

turn off the sander after use 

make sure the holes are lined up 

keep safety equipment on 

clean up 

Don'ts

put on ground while on  

keep on while not using 

put neat others whil on 

we used the sander to make our wood 

after we cut out the stencil we put it on a board and spray painted it creating our name. a circuit t machine was used to   create our stencils and it was made out of venal. When cut this out using a exato  knife . 

we created a stencil and spray painted it 

 We created a a designed a  knob for  our boxes  in tinker cad  and  printed it. 

We used the band saw  to cut out the middle of our boxes. 

Do's 

Make sure you put in SD card 

make sure that hands are away from printer while on 

make sure print less than 2 hours 

Don'ts

take your SD card without ejecting 

make a print that is too big 

 We  glued the sides of out box back together and then clamped them up together ..

 We put on  aprons and put stain on our box we needed to make sure that the stain did not get on our clothes 

We sanded the box so  every thing was clean and smooth.

Do's 

keep gloves on 

keep apron on

don't splash 

clean up

flat head screw driver and hammer to close and open 

Don'ts

touch your or other people clothes 

leave open 

leave stain out

we drew some optical illusions  that lowed us to make things look 3d 

I used super glue to attach the 3d knob 

We used the band saw to cut out the  top and the sides of four box . 

In class we learned about the our next project .We are going to make  DIY coaster for our tables in our houses. Some tools that wee need are the following:

planner Saw 

Table Saw 

Orbital sander 

Floor  Drill 

The planner Saw is used  to shape your wood  and shave it down into shape. 

Do's                     ,mbmk,n =[-;0

When using a planer saw always keep hands on the side of the machine away from the saws 

always lock the saw before putting wood trough  

turn it off when you are done

Don'ts 

When using a planer saw always keep hands on the side of the machine away from the saws 

always lock the saw before putting wood trough  

turn it off when you are done

  This is an drawn out version of my coaster.  The measurements  for the board are 3 3/4  by 3 3/4. My coaster will have two small  oak and walnut and then two big  big pieces.  We will be using the  table saw. 

Small oak 2/4 big oak is 1 1/4 

Small walnut  2/4 big is 1  2/4 

Do's 

Keep your hands away from the  saws

USe  tools to keep your hands away from the saw don't

turn it off when done using 

Don'ts 

put your hand near the saw 

stand directly in front keep

 on for long periods of time  

This is a picture of my  measurements    we where able to cut it out using the table  Saw  

 We used the table saw to cut our measured pieces into  4 smaller squares.

We put our first coat of paint on the wood