When considering the hip rafter we need the true length and 3 or 4 bevel settings.
True Length Hip
Plumb Cut Hip
Foot Cut Hip
Edge Cut Hip
(Lip Cut Hip)
Dihedral Angle
In order to calculate the lengths and bevels it is always best to visualise triangles. The main triangle shown in this image is shown yellow, where you can imagine the plumb and foot cuts and see the true length. But we only know the rise of the triangle and not the length of the hip on plan.
So first we must concentrate on the green triangle where we know the distance for half the span and the angles 45º. From which we can calculate the hip on plan.
Length of Hip on Plan
(SOA)
sin 45º = ½ Span ÷ Hip on Plan
Hip on Plan = ½ Span ÷ sin 45º
Hip on Plan = 1430 ÷ sin 45º
Hip on Plan = 1430 ÷ 0.7071
Hip on Plan = 2022mm
Hip Rafters
True Length Hip
Now we can use this to calculate the hip rafter lengths and bevels
Hip Foot Cut
(TOA)
tan (of the hip foot cut) = length of the opposite side ÷ the length of the adjacent side
tan (foot cut) = Rise 1202mm ÷ Hip on Plan 2022mm
tan (foot cut) = 1202 ÷ 2022
tan (foot cut) = 0.59446
Use inverse tan Hip Foot Cut angle = 30.73º
Note inverse of sin, cos or tan can be expressed as asin, acos or atan and uses 2nd function on a Casio calculator and is marked as sin-1 cos-1 and tan-1
Hip Plumb Cut
We can do this two ways to check
(TOA)
Tan (plumb cut) = opposite side ÷ adjacent side
tan (plumb cut) = Hip on plan 2022mm ÷ Rise 1202mm
tan (plumb cut) = 2022 ÷ 1202
tan (plumb cut) = 1.68219
Use inverse tan Hip Plumb Cut angle = 59.27º
Check all angles in a triangle must add to 180º
90º + 30.73º + 59.27º = 180º (check)
Now we can calculate the True Length of the Hip
Two ways to check
Pythagoras' theorem; a2 + b2 = c2 Where c represents the longest side so..
c2 = a2 + b2
c = √a2 + b2 (square root a2 + b2)
True Length Hip = √ Rise2 + Hip on Plan2
True Length Hip = √ 12022 + 20222
True Length Hip = √ 1444804 + 4088484
Tree Length Hip = √ 5533288
True Length Hip = 2352mm
Check sin 30.73º = Rise ÷ True Length Hip
True Length Hip = 1202 ÷ sin 30.73º
True Length Hip = 2352mm (check)
Hip Edge Cut
Most trainee carpenters find this tricky
When the two hips come together under the ridge they need to be ‘mitred’ to each other but the angle is not 45º when you place the bevel on the sloping underside of the hip. You will have developed this angle when you did your roofing geometry and that is the clue when confirming the angle by calculation. First as always we need to visualise a triangle where we know some of the lengths and angles.
Visualisation of Bevel Setting for Hip Edge Cut
Here we see a represenation of the roof in question with two intersecting planes one green and one yellow.
The green plane represents that of the ridge board
The yellow plane represents the bottom edge of the hip rafter.
We say the bottom edge because when you introduce the dihedral backing angle to the top edge of the hip then the bevel setting changes but the bottom edge can still use the bevel setting for the edge cut.
The yellow triangular plane is formed by a 90º angle between the base line, the length of the hip on plan and a perpendicular line, the length of the true length of the hip.
So we can calculate the bevel setting for the Hip Edge Cut (TOA)
Tan of angle Hip Edge Cut = Opposite side ÷ Adjacent Side
Tan of angle Hip Edge Cut = Hip on Plan ÷ True Length Hip
Tan of angle Hip Edge Cut = 2022 ÷ 2352
Tan of angle Hip Edge Cut = 0.85969
(use inverse tan) Hip Edge Cut = 40.69º
Under view of Hip
Visualisation
Hip Edge Cut
Now we need to consider the lip cut that goes under the ridge. A little bit of thought here will see that the underside of the ridge is parallel to the top edge of the wall plate. So the bevel setting that cuts the angle that fits on the wall plate (the foot cut) can be used to mark and cut this lip bevel.
Now we need to consider the fitting of the top of the rafter against the common rafter and crown rafter. Again with a little bit of thought is can be seen that the angle used over the dihedral against the common and crown is the same as that used to get the edge of the jack rafter to fit against the hip. So if we calculate the edge cut for the jack rafter we can use it here.
Visualisation
Hip Rafter Dihedral Angle
Independent learners can try and get their heads around this;
Using the image below, given that ‘U’ is equal to ‘u’ and can be any distance (say 500mm)
U = (say 500)
u = (say 500)
Hip Foot Cut Angle 30.73º (above)
sin Hip Foot Cut Angle = 0.51099
½ Dihedral Angle = Inverse Tan (U ÷ (u x sin Hip Foot Cut Angle))
½ Dihedral Angle = Inverse Tan (500 ÷ (500 x 0.51099))
½ Dihedral Angle = 62.9º