Index and Projects - 1

This page contains projects in progress or recently completed. Check back often to see what's new.

Stair railings to match those in an early 20th century home. They are made of hard maple with a fair amount of curly character.

https://goo.gl/photos/opwQrVRR1BexQA6a8

Live edge oak slab for a bathroom shelf. This slab came from a local red oak that I milled earlier this spring as a 2" thick, 12' long slab. After air drying all Summer it was recently dried in my kiln. The top was a little warped and cupped so I flattened it using a router on a bridge. After one side was flat, I flipped it over and did the other so it was flat and parallel and finished out at 1-5/8" thick. Some sanding and the main section was done. I cut a radius on the left end to match the sink, cutting it at an angle to match the live edge. I then wire brushed the edge with a rotary wire brush chucked in a drill motor. The finish was shellac followed by 6 or 7 coats of Arm-R-Seal wiping varnish. Installation was done by mounting ledger strips to the back and right wall in the bathroom, which fit into dados I cut into the slab. After the slab was slid over the ledgers I countersunk a few screws underneath through the slab and into the ledgers. No matter how you look at it the slab has no visible means of support, for a very ethereal effect.

https://goo.gl/photos/PzRNLdoL5BGZEHc78

A SketchUp drawing of the spalted maple wall clock shown in my Photo Gallery is attached below.

To open and view any of the SketchUp drawings I've posted a free download from Google can be found at this link: http://sketchup.google.com/intl/en/download/gsuviewer.html

Leaves for a table top with shop made quarter sawn white oak veneer: https://goo.gl/photos/zbUAhA9vJBLz28yZ9

Walnut bowl set. This wood came from a local tree taken down because it was threatening the homeowner's and neighbor's home. I saved a couple of sections of the trunk from the firewood pile and sawed them into thick slabs for this small project. After planing a couple of the slabs and getting a look at the beautiful curly grain, I'm sorry I didn't save more. https://goo.gl/photos/gBHBpfyXWLibHdNcA

Kitchen rehab. I did this project only because I didn't have to install new cabinets. I veneered the face frames of the existing cabinets, and designed and built new doors and drawers to give a seamless look. Moldings top and bottom and end panels to match the doors give a higher end look. The clear finish shows off the grain of the oak. I also built a frame and panel door to replace a bi-fold door for the pantry, with wire racks on the inside for additional storage. To eliminate the dead space above the refrigerator, I built a small cabinet, while allowing for the cooling requirements of the refrigerator. https://goo.gl/photos/itDaw72bQTk8AHVi9

Built in dining room hutch with curved doors: This cabinet has curved frame and panel doors and drawers as well as a lighted open shelf display area. To make the curved door and face frame rails and the curved door panels, I used a vacuum laminating technique. The link shows how this works, as well as the cabinet under construction and installation: https://goo.gl/photos/VBWjqZQWRb1K1cpc6

Simple handrails added to improve safety in my parent's home: https://goo.gl/photos/P9VxQd2hDmJ61W6D8

Window trim and shelving:

I trimmed out a corner window to match the knotty pine ceiling of this kitchen, then added a maple, butcher block style back splash and cantilevered cherry display shelves. It's a rather eclectic mix but, somehow, it all works. The design was the homeowner's. I also made the maple/cherry cutting board inset in the concrete counter top. https://goo.gl/photos/BMfeujBnQxYGEJiR8