How to Change HP ENVY 4500 Printer Cartridge? (Full Guide)

If your HP ENVY 4500 Printer has started showing faded or streaky prints, then it is time to change the ink cartridges. Replacing the cartridge is an easy procedure that keeps your printer running smoothly and ensures clear prints every time. Whether you are new to HP printers or just need a quick refresher, this post will walk you through the right steps from checking the cartridge type to installing and aligning the new one. By following the simple steps below, you can replace the cartridge without any trouble and get your printer ready to deliver great-quality prints again.

Step 1: Identify the Cartridge Type

Before you replace the cartridge, it is very important to know which type your printer model uses. The HP ENVY 4500 printer uses:

• Black Cartridge: For standard black-and-white printing.

• Tri-Color Cartridge: It has cyan, magenta, and yellow for color printing.

To check your cartridge type, you have to open the printer’s control panel or refer to the existing cartridge labels. Here are the compatible HP cartridges for your printer model - HP 61, 301, or 802 series, which depend on your region. You should always use genuine HP cartridges to ensure the best performance and prevent damage.

Step 2: Prepare the Printer for Cartridge Replacement

1. First of all, turn on your printer and wait for it to become idle.

2. Then, open the door that gives access to the ink cartridges.

3. Now, wait until the carriage stops moving completely before you try to touch the cartridges.

Tip: If the printer was off when opening the cartridge door, then the carriage may not release the cartridges. You have to wait a few seconds for it to move into position.

Step 3: Remove the Old Cartridge

1. Raise the cover of the cartridge holder.

2. And then push the cartridge backward until it stops.

3. Next, pull the cartridge up and out of the slot.

Some tips to avoid spills or damage:

• Handle cartridges carefully to prevent ink from staining your hands or surfaces.

• Replace the cartridge within 5 minutes of opening the access door to avoid the carriage moving automatically.

• Recycle the old cartridge properly.

Step 4: Prepare the New Cartridge

1. Afterward, remove the new cartridge from its packaging.

2. Take off the protective tape covering the copper-colored contacts and ink nozzles.

Important note: You should avoid touching the copper contacts or ink nozzles. Touching these parts can cause ink system failure or poor print quality.

3. For tri-color cartridges, gently shake them from side to side, as recommended by HP.

Step 5: Install the New Cartridge

1. Hold the cartridge slightly upward with the metal contacts pointing toward the back of the printer.

2. After that, place the new cartridge into the correct slot - color on the left and black on the right.

3. Also, push the cartridge in until it clicks securely.

4. Now, close the cover of the cartridge holder.

5. Finally, shut the ink cartridge access door.

Step 6: Align the Printer Cartridges

Cartridge alignment is necessary to ensure the best print quality and avoid streaks or misaligned colors.

1. Perform the instructions on the printer’s control panel to start alignment.

2. Now, the printer will print an alignment page automatically.

3. Place the alignment page face down on the scanner glass and close the lid.

4. And then, press the OK button to complete scanning.

Tip: In case the printer fails to print an alignment page, you have to navigate to Tools > Align Printer on the control panel and then try again.

Step 7: Test the HP Printer

After installing and aligning the ink cartridges on your printer:

1. It’s time to take a print test to verify the installation.

2. Check for any streaks, missing colors, or faded areas.

Troubleshooting:

1. If print quality is poor, then remove and reinstall the cartridge.

2. Make sure you have no protective tape remaining on the cartridge.

3. Clean the printer nozzles if necessary using the printer maintenance menu.

Step 8: Purchase Genuine HP Cartridges

Always use genuine HP cartridges for your ENVY 4500 printer to ensure reliable printing and avoid errors. You can buy them from local retail stores or online at the HP official website. Compatible cartridges vary by region, including HP 61, 301, 122, or 802 series for black and tri-color.

By following the steps above, your HP ENVY printer is ready to create high-quality prints again. Try to check ink levels and replace cartridges regularly to help maintain consistent performance and avoid any interruptions during printing.

   Frequently Asked Questions

Question

How to Reset HP ENVY Printer After Changing an Ink Cartridge?

Learn How to Reset your HP Printer after installing a new ink cartridge, start by turning it off and unplugging the power cord for about a minute. Then, plug it back in and switch it on to let the printer refresh its settings. In case the problem continues, remove the ink cartridges, then repeat the power cycle, and place the cartridges back. If the printer still doesn’t respond or shows an error, then you can try a factory reset from the control panel or through the HP Smart app to restore default settings.

Question

How Do I check ink levels on My HP ENVY Printer?

You can easily check the ink levels on the HP printer in a few ways. The simplest option is through the printer’s control panel - you just have to look for the ink drop or cartridge icon to see the current levels. Also, you can use the HP Smart app on your mobile or desktop, which displays the ink levels right on the main screen once your printer is connected. Another option is the HP Printer Assistant software on your computer, where you can open the “Estimated Ink Levels” tab to view how much ink remains in each cartridge.

Question

How Can I Clean My HP Printer ink Cartridge?

You can clean your printer ink cartridge by using the printer’s built-in cleaning feature or the HP Smart app, which automatically clears dried ink or blockages. If the print quality doesn’t improve, then you can try cleaning it manually. To do this, you need to turn off the printer, then remove the cartridge, and wipe the printhead and metal contacts with a lint-free cloth slightly dampened with distilled water. After that, let it dry before putting it back. Now, automatic cleaning is best to start with, but manual cleaning helps when the cartridge is still not printing properly.

Source: How to Change HP ENVY Printer Cartridge