For this lesson, we used/learned the following tools to create a heart in fusion360:

• 1st create sketch(xy axis) upload an image of a heart to trace using the Canvas tool.

• 2nd, create new sketch(xy axis) to trace over the canvas using the Fit Point Spline tool. Then draw a line at the place you want to Mirror it.

•  3rd, Extrude the heart

•  4th, we used the Fillet tool to select the edges to smoothen it.

For this lesson, we used/learned the following tools to create a 3D heart in fusion360:

• 1st create sketch (xy axis) upload an image of a heart to trace using the Canvas tool.

• 2nd, create new sketch(xy axis) trace over the canvas using the Fit Point Spline tool. Then draw a line at the place where you want to Mirror it.

• 3rd, Offset your sketch

•  4rd, Extrude the heart

•  5th, Then use the Fillet tool to smoothen ALL the edge

For this lesson, we used/learned the following tools to create a tissue box in fusion360:

• 1st create the base(center rectangle) of the tissue box(sketch on xy axis)

• 2nd Extrude 

• 3rd Shell the structure.

• 4th create sketch(rectangle, smaller than the base rectangle) on the plane that covers the top of the tissue box(this would be where the tissue comes out)

• Extrude the structure and select the mode: "Cut". Then make sure it cuts through the top of the structure.

For this lesson, we used/learned the following tools to create a tissue box to print in fusion360:

• 1st create the base( center rectangle) of the tissue box(sketch on xy axis) and extrude

• 2nd select the plane that represents the thickness of the base and sketch another rectangle(side1), then extrude

• 3rd, mirror the sketch that we just drew(side1) to the other side.

• repeat the steps 2 and 3 to create the rest of the sides

• 4th, sketch the top(as well as sketching the hole on top) and extrude(dont extrude the hole)

For this lesson, we used/learned the following tools to create a Lego Block in fusion360:

• 1st, Select the xy axis and sketch a center rectangle

• 2nd, extrude

• 3rd, Select the top face of the prism and create a circle on the top right corner.

• 4th Use the Rectangular pattern tool to select the circle and multiply the quantity.

• 5th, extrude

• 6th, use the Shell tool to hollow the rectangle

• 7th, create a circle on the bottom of the brick, offset,  and use Rectangular pattern to create the 3 tubes at the bottom.

For this lesson, we used/learned the following tools to create a macaroni in fusion360:

• 1st sketch a circle on the zx plane.

• 2nd use the revolve tool to revolve the circle 180 degrees(By first selecting the profile and then the axis you want the structure to rotate around)

• 3rd Shell the structure

For this lesson, we used/learned the following tools to create a bowl in fusion360:

• 1st sketch using the arc tool to create a quarter of a circle

• 2nd revolve it 360 degrees,

• 3rd Shell the structure

For this lesson, we used/learned the following tools to create a vase in fusion360:

• 1st create sketch on the zx axis and use the fit point spline, line, and arc tool to create one half of the vase shape.

• 2nd revolve 360 degrees 

• 3rd shell the structure

• 4th use the fillet tool to smoothen the edges of the top of the vase

For this lesson, we used/learned the following tools to create a Candle Holder in fusion360:

• 1st create sketch on the zx axis and use the fit point spline and arc tool to create one half of the vase shape.

• 2nd revolve 360 degrees.

For this lesson, we used/learned the following tools to create a glass jar in fusion360:

• 1st use the canvas tool to import a picture of a jar.

• 2nd create sketch on the zx axis and use the line and arc tool to trace one half of the jar shape.

• 3rd revolve 360 degrees.

• 4th shell the structure

• 5th use the Fillet tool to smoothen the top of the jar.

For this lesson/quiz, we used/learned the following tools to create a bottle cap in fusion360:

• 1st create sketch(zx axis) to create half of the bottom of the bottle cap first.

• 2nd revolve 360 degrees

• 3rd create sketch(zx axis) to create the handle

• 4th Extrude both ways in order to make sure that the handle is in the middle