Project Description:
This project focuses on the design, development, and testing of a reaction wheel stabilization system for small-scale aerospace applications. The system uses a high-speed rotating wheel, embedded sensors, and PID-based control to generate corrective torque and improve rotational stability. Through CAD design, electronics integration, Arduino/ESP32 programming, and physical testing, this project explores how mechanical design and control systems can work together to improve rocket attitude control and disturbance rejection.
Engineering Project Flow
Problem / Objective:
Develop a reaction wheel stabilization system for a rocket payload to help reduce unwanted spin about the yaw axis during flight. The goal was to combine mechanical design, embedded controls, sensor feedback, and testing into a compact system that could fit within the rocket body.
Constraints:
The design had to account for limited payload space, motor speed, flywheel balance, mounting strength, sensor accuracy, wiring, battery power, and safe operation during testing. The system also needed to be lightweight enough for rocket integration while still producing enough angular momentum to counter unwanted rotation.
Design Choices:
The system used an Arduino Nano, MPU-6050 IMU, BTS7960 motor driver, and high-speed DC motor to create a closed-loop control system. A 3D-printed flywheel was designed and mounted to the motor shaft using a custom coupler. PID control logic was used to read angular motion from the IMU and adjust motor response to help dampen rotational motion.
Cost / Budget Considerations:
The project focused on low-cost, accessible components that could be purchased, assembled, and tested quickly. Components such as the Arduino Nano, IMU, motor driver, DC motor, wiring, buttons, LEDs, and 3D-printed parts allowed the design to stay affordable while still demonstrating the core control and stabilization concept.
Testing / Validation Considerations:
Testing focused on verifying sensor readings, motor response, PID behavior, wiring reliability, and the reaction wheel’s ability to respond to rotational disturbance. The system was evaluated through bench testing, code debugging, motor speed checks, and control response observations. FEA was also used to review the flywheel and mounting design under expected loading conditions before further integration.
Documentation:
Produced CAD models, wiring layouts, embedded control code, FEA results, and test documentation for the reaction wheel system. The project documentation helped track mechanical design decisions, electronics integration, control logic, and future improvements for rocket payload integration.
Reaction Wheel Attitude Control System
This system was designed as a small-scale attitude control prototype for rocket stabilization. The reaction wheel uses a high-speed rotating mass to generate corrective torque when the body experiences unwanted rotation. An onboard microcontroller processes sensor feedback from the IMU and adjusts motor output through PID control to help resist disturbances and return the system toward a stable orientation.
For validation, I suspended the system to allow free rotational motion and used compressed air to create sudden disturbance inputs similar to what the system could experience during launch or flight. I also developed a wired tuning controller that allowed live adjustment of PID values while the system was moving. This made it possible to test different control responses in real time and improve stability through iterative code updates, physical testing, and system refinement.
Key Features:
CAD-designed reaction wheel assembly, IMU-based feedback, embedded PID control, live PID tuning remote, suspended test rig, compressed-air disturbance testing, iterative validation, and hands-on electromechanical integration.
Iterative Testing and Real-Time Control Validation
I performed iterative testing and validation on the reaction wheel stabilization system by repeatedly updating the control code, testing system response, and refining the mechanical and electrical setup. To simulate rocket launch conditions, I suspended the system to allow free rotational movement, while using compressed air to create sudden disturbances similar to the rotational effects experienced during flight. I also developed a wired controller/remote that allowed real-time PID tuning while the system was in motion, making it possible to adjust the proportional, integral, and derivative gains instantly during testing. This process helped improve stability, response accuracy, and overall control performance through hands-on experimentation and validation.
System V Model
Below is my Systems Engineering V-Model to define, develop, integrate, and verify the reaction wheel stabilization system. The process linked system-level stability requirements to subsystem design, component selection, prototype integration, testing, and validation in preparation for flight testing.
Reaction Wheel Design Iterations & Structural Validation
The reaction wheel and base went through multiple design iterations to improve mass reduction, space efficiency, manufacturability, and overall system integration. Each version was evaluated based on size constraints, mounting requirements, wheel clearance, component placement, and the need to keep the assembly lightweight while still maintaining enough structural rigidity for testing and flight-like conditions. These design changes helped optimize the system layout without sacrificing performance or stability.
Finite element analysis was also performed to identify stress concentrations and potential weak points in the reaction wheel and support structure. The FEA results helped guide design improvements by showing where reinforcement was needed, especially around mounting locations, shaft interfaces, and areas exposed to rotational loading. This allowed the final design to better withstand operational forces while avoiding unnecessary material use.
Material selection was an important part of the project because the reaction wheel needed to resist deformation under load while spinning at high speed. Nylon carbon fiber was selected for its improved stiffness, strength-to-weight ratio, and dimensional stability compared to standard polymers. After printing, annealing was considered/used as part of the production process to improve heat resistance and mechanical stability, helping the part better maintain its shape and performance during operation.
Results
The Boundary Conditions & Applied Loading image shows how the reaction wheel was constrained and loaded before running the simulation, while the Initial Finite Element Mesh shows the triangular element mesh used to divide the geometry for analysis. The Undeformed Contour Plot and Deformed Contour Plot compare the original and displaced shapes under von Mises stress, showing that the highest stress concentrations occur around the curved cutouts, screw holes, and outer rim regions where geometry changes create localized stress buildup. The Displacement Magnitude Contour Plot shows the overall deformation pattern, with the largest displacement occurring near the outer edge of the wheel and lower displacement near the central hub. Overall, the FEA results suggest that the reaction wheel maintains its general shape under the simulated loading, but the cutouts and outer rim are the most important areas to monitor for stress and deflection.
Improvements to Make Based on the Results
Based on the FEA results, the overall reaction wheel geometry performed well, but the analysis identified higher stress and displacement near the outer rim, screw holes, and curved cutout regions. Future design improvements would include increasing fillet radii around the cutouts, locally reinforcing the outer ring, and refining the mesh near high-stress features to improve result accuracy before final manufacturing.