Embedded Files
Ideation
Ideation
Tell us about your assignment's idea for this week. Why do you care about this idea? What inspired you? (Please include images or links to sources of inspiration)
Tell us about your assignment's idea for this week. Why do you care about this idea? What inspired you? (Please include images or links to sources of inspiration)
Title of Media
a simple Fan with led indication
power connected is red and green the fan is on
the case was made of cardboard and assembled with hot glue gun
the project was simple to use 2 outputs and a power supply
i choosed the 5v power supply to power both the rgb led and the Fan
i will connect because fan and rgb led on parallel and they are both rated for 5V
gif
Tool Chain
Tool Chain
Which software/machines/materials did you use in the assignment? Why?
Which software/machines/materials did you use in the assignment? Why?
i used tinkercade to but the circuit and make sure i don't fry more components :D
component :
5v power adapter as my power supply source
RGB Led light ... i used the green and red pins
2 Resistors 220 ohm >>> for red and green terminals in RGB led
1 Resistor 330 ohm >>> i found that the RGB led light is too bright so i added this to the cathode terminal to lower the intensity a little and it worked :D
3 pin Mini Slide Switch
a 5v dc Mini Fan
some male to male jumper wires
mini circuit board
hot glue gun and cardboard for the caseing
the circuit diagram on Tinkercad
Design/Preparation Process
Design/Preparation Process
Explain the design and/or preparation process of your assignment. How did you use the tool or software to design and/or prepare your assignment before fabrication/implementation?
Explain the design and/or preparation process of your assignment. How did you use the tool or software to design and/or prepare your assignment before fabrication/implementation?
Tinkercad simulation
used Tinkercads simulation the to on and off
i started with connecting the power source terminals
then connected the switch middle (common pin) to the +v, then added the motor and the rgb light pins red and green with a 220 ohm resistors one for each pin in the switch so when off it will emit red to indicate that there is power current , when turning on the switch the light will turn green and the motor will turn on too , at last i connect the cathode pin of the rgb led light to another resistor 330 ohm to lower the intensity a little and it worked :D and connected the motor on parallel
then i did the same circuit connections on the mini board and it worked
then did the casing cardboard i know its not perfect but i tried to not waste cardboard for the final project prototype
Development/Implementation Process
Development/Implementation Process
Explain the development/implementation process of your assignment. How did you use the machine/tool to manufacture or implement the design of your assignment?
Explain the development/implementation process of your assignment. How did you use the machine/tool to manufacture or implement the design of your assignment?
I used the small breadboard to make my project compact and to not waste Cardboard i need for my final project prototype
had some troubles with the breadboard connectivity but finally it worked as it should
I used the cardboard box to cramp all components and made some cuts and opening for power jack and led and the on/off button and the fan itself and then attached the sides with hot glue
Title of Media
Community of Learning
Community of Learning
Did you ask for feedback? What are the ideas that others have contributed or suggested? What was someone else’s idea that you built upon? How did you help your peers? How did your peers help you?
Did you ask for feedback? What are the ideas that others have contributed or suggested? What was someone else’s idea that you built upon? How did you help your peers? How did your peers help you?
we made a RC Car with an H-Bridge
Overcoming Challenges
Overcoming Challenges
When you got stuck, what/who did you turn to? At what point did you have to pause to research or learn more before moving on? What are some mistakes, pitfalls, or challenges that others can avoid if they were doing this assignment?
When you got stuck, what/who did you turn to? At what point did you have to pause to research or learn more before moving on? What are some mistakes, pitfalls, or challenges that others can avoid if they were doing this assignment?
i wanted to use the 7 segment screen to indicate fan speed level (1,2,3) and variable fan speed as well but had some troubles connecting wires in such a small box i already made so i gave it up
Final Project
Final Project
How can you use the skills and knowledge that you've acquired this week in your final project?
How can you use the skills and knowledge that you've acquired this week in your final project?
definitely will use hooking on serial or parallel upon device consumption and power
WOW!
WOW!
What is the coolest thing that you've learned this week? What is something that you will never forget from this week?
What is the coolest thing that you've learned this week? What is something that you will never forget from this week?
Title of Media
Weekly Digest [OPTIONAL]
Weekly Digest [OPTIONAL]
Tell us about any other cool things that you've made this week: in the Hands-on activity, tutorial examples, exercises, or any other cool mini-project that you tried out aside from the assignment.
Tell us about any other cool things that you've made this week: in the Hands-on activity, tutorial examples, exercises, or any other cool mini-project that you tried out aside from the assignment.
Title of Media
Assignment Design Files
Assignment Design Files
Page updated
Report abuse