Error 1571
I was getting 1571 Error after paper jam error 25701. When I would get this error the machine would have me check for any paper then it would display Error 1571. I searched code on Porthos and it refered to "No drum reference available for current drum".
Steps to clear that was to enter SDS and set parameter "Ignore missing drum reference" to ignore.
SDS: parameter/printer/cold and warm process/ Ignore missing drum reference.
*I did not Activate the special test. I simply re-booted the machine.
1070128725 box filter assy replace every 5 million on varioprints
1503/1513 developer motor will need replacement.
Noise or humming coming from Warm process area it was the TTF unit assy replace solved issue
1533 Replace encoder
Don’t- just replace drum instead
1571 Drum reference error/missing
⁃ either rerun the data reference SMS>Tasks>Installation Tasks 2>Run Drum Reference
⁃ Or choose to ignore - SMS>Tasks>Installation Tasks 1>Ignore Drum Reference
6124 - spiral cleaner.
6132 TTF belt replacement needed
6505 uneven heating of TTF belt
⁃ Replace side bulbs
6509-Can be several things try -Power supply-Pre heater or harness on power supply also try Sensor box and Heat on demand assy one of these should solve issue.
6501/6503/xx05/xx07 TTF temp too high
⁃ check HOD for burnt bulbs
⁃ Replace power supply
6520 - Replace the preheater as the sensor has gone out.
6525 - WPR drive motor needs replacing
Part #1070023491
6537 WPR drive motor out of range
Spiral 35 is fused to the counter pressure assy. Belt change needed.
6542 - WPR out of whack
If just replaced TTF assembly or spring cable. Reset and before error occurs get into maintenance mode
Run the soft close test.
6548 - Rotate spiral cleaner driver coupling to up position also replaced cleaner drive assy as well
11555 no communication to Beagle
Inspect Beagle board if lit and Sting is not, properly shut down the unit.
Unplug it from power and wait 10 mins
Plug back in.
It should boot up correctly.
11577 - network IP conflict
Disconnect CAT cable and hit moon
If it comes back alive all is good. Their IT needs to resolve the conflict.
***Check for solid red light on the NIP.
NIP is faulty and need replacement. Part #1070088944.
Also replace the 5v transformer
Part #1070034102
to be safe and check sliding paper path tray umbilical arm for fraying wires. A short here has been known to blow the NIP.
12901/2/3/4 - the EPIMs drive motor for the clutches up front has gone bad and needs replacing.
14512 - tray 1 motor out
14542 - paper blocking the tray bus in the back of trays 3 or 4
16705 - if paper is coming from internal trays 1 or 2 check the back guide is too far back.
Adjust enough to see gaps.
16711 - if you see skew and faint image perform soft pinch test. Spring cable has loosened and will need replacing soon
16715 - unit thinks it doesn’t have a finisher configured.
16720 - Z sensor
Clean the sensor in the ePIM,also check the rollers on the heat exchanger lower if there turning evenly also counter pressure assy check as well could be that belt is all the way to side that can be causing skew issues those two things that I found out
16771 - horizontal paper transport output counter pressure roller broken off the solenoid.
25541 - door sensor is not being depressed fully. Replace the tongue
25701 - Check the lock sensor pin on the door it may be pushed into the door permanently. Replace
1850225 - Staple removal error.
When all looks good, but error persists, hard reboot to resolve.
1850242 - The action of the stapler is blocked from moving. Could be a few things.
1850282 - Estrangement unit (FM1-A176-000) needs cleaning or replacement in finisher entrance
1850288 - Knurled belts jammed up in the dispose unit. May need replacement
1850291 - Stapler is stuck in closed position. Just replace- do not submit for fix.
1870200 - check inside the unit and see if the #1 handle is missing and in the up mag locked position.
1870225 - Stapler motor error
If digital code flashes “J-24” replace the stapler.
2250222 - PCT power supply 40w failure
Check the back connector on the spiral cleaner assembly. It’s most likely broke. Just replace.
2250252 - tray lift motor in tray 1 or 2.
2250283 - images are stretched horizontally. Replace encoder.