This control switches between Dacron Frame and Two Piles (two layers of fabric) style panel cuts - result will be seen in the 2D view
This control allows you to switch the alignment of your LE Panels - either aligned/rotated to the Canopy attachment line or to an average between the two closing seam edges.
Sets the seam allowance of the seams between each of the leading edges segments
TIP: Check with your factory/prototype supplier for their requirements
Sets the seam allowance of the leading edge closing seam
TIP: Check with your factory/prototype supplier for their requirements
Sets the seam allowance of the seams between each of the strut segments
TIP: Check with your factory/prototype supplier for their requirements
Sets the seam allowance of the closing seam/canopy attachment seam of the struts
TIP: Check with your factory/prototype supplier for their requirements
Checking this box will change the LE and Strut Seam Allowances to have beveled rather than sharp corners. Also adds further alignment marks on these seams.
Sets the seam allowance of all the canopy and canopy reinforcement panels
PLEASE NOTE: The seam allowance of the Canopy to Leading Edge attachment is set to zero by default
TIP: Check with your factory/prototype supplier for their requirements
Sets the seam allowance of all the canopy and canopy reinforcement panels along the trailing edge
TIP: Check with your factory/prototype supplier for their requirements
Sets the seam allowance of all the canopy and canopy reinforcement panels at the seams with struts
TIP: Check with your factory/prototype supplier for their requirements
Sets the hole diameter for the strut inflation/one pump fittings
TIP: Check with your factory/prototype supplier for the diameter required for their stock valves
Sets the distance in mm from the LE for the strut inflation/one pump valves.
Please note: The valves are set at 90 deg to the strut center line
Sets the hole diameter for the leading edge one pump fittings
TIP: Check with your factory/prototype supplier for the diameter required for their stock valves
Sets the distance from the side of the strut of the leading edge one pump fittings
Adjusts the position of the leading edge one pump fittings around the leading edge
Sets the hole diameter for the leading edge inflation valve
TIP: Check with your factory/prototype supplier for the diameter required for their stock valves
Sets the distance from the side of the strut of the leading edge inflation valve
Adjusts the postion of the leading edge inflation valve around the leading edge
Sets the diameter of the circlar patch on the canopy to protect from canopy wear on the inflation valve
Sets the height of the panel marking labels
TIP: Check with your factory/prototype supplier for their requirements
Adds % to the overall length of the leading edge bladder to assist in installation and fitment
Adds % to just the wingtip length of the leading edge bladder to assist in installation and fitment
TIP: This is helpful for getting a better fit through the corner curve of your wing
Adds an additional offset to the very end of the LE Bladder.
TIP: This is helpful for adding material to be folded back in the tuck flap
Adds an additional material to the center of the LE Bladder.
TIP: This is helpful for adding material between the inlet and center strut valve
Adds % to the overall diameter of the LE bladder to assist in installation and fitment
Adds % to the overall length of the strut bladders to assist in installation and fitment
Adds an additional offset to the TE end of the Strut Bladders.
TIP: This is helpful for adding material to be folded back in the tuck flap
Adds % length to the strut bladders between the valve to the LE to assist in installation and fitment
Adds an additional offset to the LE end of the Strut Bladders.
TIP: This is helpful for adding material to fill out the front of the strut
Adds % to the overall length of the strut bladders to assist in installation and fitment
Sets the seam allowance of the all of your bladders
TIP: Check with your factory/prototype supplier for their requirements
Sets the length of the leading edge bladder installation zipper
Sets the offset from the seam of a the leading edge bladder installation zipper
Width of the leading edge bridle attachment point reinforcement patches
Length of the leading edge bridle attachment point reinforcement patches
Checking this box will remove the patches and attachement markings not currently assigned the a bridle cascade
Sets overall length of the Vee webbings for the rear line attachments
Sets internal angle of the Vee webbings for the rear line attachments
Sets the offset distance of the reinforcement patches for the rear line attachments
Sets width of the webbing used for the rear line attachments
TIP: Check with your factory/prototype supplier for their stock webbing widths
Set your material details here to have the details listed on your 2D delivery file
Set your material colour here to have the details listed on your 2D delivery file
Leading edge and strut fabric weight in grams per square meter, used to calculate the weight of the kite
Set your material details here to have the details listed on your 2D delivery file
Set your material colour here to have the details listed on your 2D delivery file
Canopy fabric weight in grams per square meter, used to calculate the weight of the kite
Set your material details here to have the details listed on your 2D delivery file
Set your material colour here to have the details listed on your 2D delivery file
Reinforcement material weight in grams per square meter, used to calculate the weight of the kite
Bladder material weight in grams per square meter, used to calculate the weight of the kite
Sets the layer colour of the cut lines in the 2D export file
TIP: Check with your factory/prototype supplier for their requirements
Sets the layer colour of the seam lines in the 2D export file
TIP: Check with your factory/prototype supplier for their requirements
Sets the layer colour of the panel markings in the 2D export file
TIP: Check with your factory/prototype supplier for their requirements
Sets the layer colour of the point marking in the 2D export file
TIP: Check with your factory/prototype supplier for their requirements
Sets the layer colour of the notes/information in the 2D export file
TIP: Check with your factory/prototype supplier for their requirements