Embedded Files
If a part is broken or not functioning properly, look through the different scenarios/parts in order to fix it or replace the part with the provided link:
If a part is broken or not functioning properly, look through the different scenarios/parts in order to fix it or replace the part with the provided link:
*If the lights do not turn on then the lights themself, or the outlet is not working. Test the lights by plugging them into a working outlet. If still not working, there is an issue with the lights or wires connecting to the lights and will need to be replaced.
Replacing Grow Light: https://www.amazon.com/Lights-Equivalent-Spectrum-Dimmable-Seedlings/dp/B08PYWSFY5/ref=sr_1_6?crid=16QE967SV7YGC&keywords=1%27%2Bgrow%2Blight&qid=1640016059&sprefix=1%27%2Bgrow%2Blight%2Caps%2C198&sr=8-6&th=1
Unplug old/broken lights.
Swap out old lights with the new lights, including using the new wires to connect to the lights.
Plug them into the power block.
*If the bubbles coming out from the bar at the bottom of the tank stop, then you might have a problem with the bar itself (the air stone), the air pump feeding into the bar, or the tubbing connecting the bar and pump.
Replacing Air Stone: https://www.amazon.com/dp/B08PBN396D/ref=sspa_dk_detail_1?psc=1&pd_rd_i=B08PBN396D&pd_rd_w=eD4Tc&pf_rd_p=54ed5474-54a8-4c7f-a88a-45f748d18166&pd_rd_wg=RZs14&pf_rd_r=2EEGK9EGYGTXFQ2BXVB3&pd_rd_r=dd4bdebe-4bfd-4565-b04c-e8b84b6e6005&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUEyTEMwQTRMWDJNTUQ2JmVuY3J5cHRlZElkPUEwNTUzNjA3QUZWWVZUNk9DVjM3JmVuY3J5cHRlZEFkSWQ9QTAzNDYzMjAxM0FGM1Q1M0laMllGJndpZGdldE5hbWU9c3BfZGV0YWlsX3RoZW1hdGljJmFjdGlvbj1jbGlja1JlZGlyZWN0JmRvTm90TG9nQ2xpY2s9dHJ1ZQ==
Take the old air stone out of the water.
Disconnect the tubing.
Connect the tubbing to the new air stone.
Place new air stone back in the water.
Replacing Air Pump: https://www.amazon.com/dp/B098Q98395/ref=twister_B094HX53VR?_encoding=UTF8&psc=1
Disconnect from the tubbing and unplug from power.
Connect the new pump to the tubbing and plug it into one of the power blocks.
After taking it out of the water, disconnect the tube from both the air stone and air pump.
Take the new tube and connect it to both ends.
reinsert the tubing in the water and restart the system.
*If the water is leaking = then there is most likely a hole in the container that holds the water. Try to locate the hole and use duct tape to seal it. If it still is leaking from the container, a replacement may be needed.
Replacing Container: https://www.amazon.com/Sterilite-20518006-Stackable-Storage-Drawer/dp/B001MY0NGE/ref=sr_1_3?keywords=plastic+one+level+drawer&qid=1639673497&sr=8-3
Take off the lid and pull out the drawer.
Dump out the water and take out anything in the drawer then replace the old drawer with the new drawer.
Then put new water and nutrients in the drawer then put everything you took out of the old draw into the new drawer except the old water.
Place the lid back on and start the system.
*If any of the other parts have been lost or ran out of them, the order links are below to replace them:
Fertilizer: https://www.amazon.com/dp/B000HACFUQ/ref=twister_B09C1FBCZR?_encoding=UTF8&psc=1
Epsom Salt: https://www.target.com/p/epsom-salt-4lb-up-38-up-8482/-/A-11454531#lnk=sametab
Power Cube: https://www.target.com/p/just-wireless-1-0a-5w-1-port-usb-a-home-charger-white/-/A-50676560#lnk=sametab
Green Foam: https://www.michaels.com/floracraft-wetfom-brick-green/10009948.html#
Wet brick of foam.
Cut the brick into cubes that are approximately 1/4 inch x 1/4 inch.
Place cubes around the plant.
Store remaining cubes in a plastic bag.
*Need access to a 3D printer.
Plastic Grow Cups: https://drive.google.com/file/d/1Qh5QdzPBz1iZeY58H-yY5iJpuG1ZusFH/view
Download the link above on a computer.
Put it into the 3D printing software and print as many as needed.
Put the product in an acid bath to remove the excess waste material.
Reinsert the cups into the frame and place plants inside with green foam cubes.
Page updated
Google Sites
Report abuse