International Journal Papers

(*) Corresponding author

2024

48. Construction of ductile fracture locus at negative stress triaxiality using a newly proposed V-notch compression test with acoustic emission technique,

J.H. Kwon, J.M. Heo, M.T. Tran, N.T. Nguyen, H.W. Lee, H.S. Joo, S.H. Park, K.H. Lee, D.W. Kim, Y.G. Jeong, D.-K. Kim*,

International Journal of Mechanical Sciences, 2024, In press (IF 7.3, JCR 3.6%)

47. Robust detection of ductile fracture by acoustic emission data-driven unsupervised learning,

J.H. Kwon, N.T. Nguyen, M.T. Tran, H.W. Lee, H.S. Joo, S.H. Park, K.H. Lee, D.W. Kim, Y.G. Jeong, D.-K. Kim*,

International Journal of Mechanical Sciences, 2024, 109420 (IF 7.3, JCR 3.6%) https://doi.org/10.1016/j.ijmecsci.2024.109420

46. Residual stress relief strategy in thick steel weldments via local induction heat treatment: simulation and neutron diffraction experiment,

H. Wu, Z. Shan, W. Woo, H.B. Chae, D.-K. Kim*,

Materials Science and Engineering A 902, June 2024, 146612 (IF 6.4, JCR 7.6%) https://doi.org/10.1016/j.msea.2024.146612

45. Microstructure-based modeling of deformation and damage behavior of extruded and additively manufactured 316L stainless steels,

H. Wang, H.W. Lee, M.T. Tran, D.-K. Kim*,

Materials 17, May 2024, 2360 (IF 3.4, JCR Q2) https://doi.org/10.3390/ma17102360

44. Crystal plasticity finite element analyses on the formability of AA6061 aluminum alloy with different ageing treatments,

H. Wang, H.W. Lee, S.H. Kang, D.-K. Kim,

Metals 14, April 2024, 503 (IF 2.9, JCR Q2) https://doi.org/10.3390/met14050503

43. Efficient Residual Stress Mitigation in Additively Manufactured 18Ni300 Maraging Steel,

Z. Shan, M.S. Pham, M.T. Tran, J.S. An, S.-K. Hwang, H.W. Lee, D.-K. Kim*,

International Journal of Mechanical Sciences 268, April 2024, 109055 (IF 7.3, JCR 3.6%) https://doi.org/10.1016/j.ijmecsci.2024.109055

2023

42. Micromechanical properties and deformation behavior of the constituent phases in 3rd generation complex phase AHSS: In-situ neutron experiment and crystal plasticity simulation,

M.T. Tran, X.M. Nguyen, H. Kim, H. Chae, W. Woo, H.W. Lee, D.-K. Kim*,

International Journal of Plasticity 171, December 2023, 103812 (IF 9.8, JCR 2.2%) https://doi.org/10.1016/j.ijplas.2023.103812

41. Simultaneous control of mechanical strength and hierarchical porosity in freeze-casted porous alumina by two-step sintering,

S.-C. Jeon, J.-W. Woo, S.-H. Kim, J.-H. Ha, D.-Y. Yang, K.-S. Moon, H. Wu, D.-K. Kim*,

Journal of the American Ceramic Society, September 2023, 1-16 (IF 3.9, JCR Q1) https://doi.org/10.1111/jace.19430

40. In-situ EBSD observation and simulation of free surface roughening and ductile failure in the ultra-thin ferritic stainless steel sheet,

M.T. Tran, S.-K. Hwang, A R. Jo, H.W. Lee, D.-K. Kim*,

Materials Science and Engineering A 883, September 2023, 145489 (IF 6.4, JCR 7.6%) https://doi.org/10.1016/j.msea.2023.145489

39. Correlation of cryogenic deformation mechanisms to excellent strength-ductility of CrCoNi medium entropy alloy processed by selective laser melting,

K.-H. Jung, M.T. Tran, Z. Shan, H.W. Lee, S.-K. Hwang, D.-K. Kim*,

Journal of Materials Research and Technology 22, January 2023, 2297-2315 (IF 6.4, JCR 10%) https://doi.org/10.1016/j.jmrt.2022.12.084

38. Multiscale framework for prediction of residual stress in additively manufactured functionally graded material,

Z. Shan, M.T. Tran, W. Woo, S.-K. Hwang, H. Wang, V. Luzin, Ed.J. Kingston, M.R. Hill, A. DeWald, D.-K. Kim*,

Additive Manufacturing 61, January 2023, 103378 (IF 11.0, JCR 2%) https://doi.org/10.1016/j.addma.2022.103378

2022

37. Formability improvement in multi-stage stamping of metallic bipolar plate for proton exchange membrane fuel cell,

M.T. Tran, D.H. Lee, H.W. Lee, D.-K. Kim*,

International Journal of Hydrogen Energy 47, Decembr 2022, 40008-40025 (IF 7.2, JCR Q1) https://doi.org/10.1016/j.ijhydene.2022.09.163

36. Crystal plasticity finite element analysis of size effect on the formability of ultra-thin ferritic stainless steel sheet for fuel cell bipolar plate,

M.T. Tran, H. Wang, H.W. Lee, D.-K. Kim*,

International Journal of Plasticity 154, July 2022, 103298 (IF 9.8, JCR 2.2%) https://doi.org/10.1016/j.ijplas.2022.103298

2021

35. Multiple deformation scheme in direct energy deposited CoCrNi medium entropy alloy at 210K,

Y.S. Kim, H. Chae, W. Woo, D.-K. Kim, D.-H. Lee, S. Harjo, T. Kawasaki, S.Y. Lee,

Materials Science and Engineering A 828, November 2021, 142059 (IF 6.4, JCR 7.6%) https://doi.org/10.1016/j.msea.2021.142059

34. Effect of hot isostatic pressing on the cryogenic mechanical properties of CrCoNi medium entropy alloy processed by direct energy deposition,

M.T. Tran, T.H. Nguyen, D.-K. Kim*, W. Woo, S.-H. Choi, H.W. Lee, H. Wang,

Materials Science and Engineering A 828, November 2021, 142110 (IF 6.4, JCR 7.6%) https://doi.org/10.1016/j.msea.2021.142110

33. Die Design for Extrusion Process of Titanium Seamless Tube Using Finite Element Analysis,

B.-J. Choi, I.Y. Moon, Y.-S. Oh, S.-H. Kang, S.-J. Kim, J. Jung, J.-H. Kim, D.-K. Kim, H.W. Lee,

Metals 11, August 2021, 1338 (IF 2.9, JCR Q1) https://doi.org/10.3390/met11091338

32. Earing reduction by varying blank holding force in deep drawing with deep neural network,

M.T. Tran, Z. Shan, H.W. Lee, D.-K. Kim*,

Metals 11, February 2021, 395 (IF 2.9, JCR Q1) https://doi.org/10.3390/met11030395

2020

31. A new contour method for rapid evaluation of the cross-sectional residual stress distribution in complex geometries using a 3D scanner,

H. Wang, D.-K. Kim*, W. Woo, S.-H. Choi, S.Y. Lee, S.-K. Hwang,

Journal of Mechanical Science and Technology 34, April 2020, 1989-1996 (IF 1.6, JCR Q3) https://doi.org/10.1007/s12206-020-0420-0

30. Stacking fault energy analyses of additively manufactured stainless steel 316L and CrCoNi medium entropy alloy using in situ neutron diffraction,

W. Woo, J.S. Jeong, D.-K. Kim, C.M. Lee, S.-H. Choi, J.-Y. Suh, S.Y. Lee, H. Stefanus,

Scientific Reports 10, January 2020, 1350 (IF 4.6, JCR Q2) https://doi.org/10.1038/s41598-020-58273-3

2019

29. Effect of quenching tempering-post weld heat treatment on microstructure and mechanical properties of laser-arc hybrid welded boron steel,

H.W. Lee, K.-J. Yu, M.T. Tran, I.-Y. Moon, Y.-S. Oh, S.-H. Kang, D.-K. Kim*,

Materials 12, September 2019, 2862 (IF 3.4, JCR Q2) https://doi.org/10.3390/ma12182862

28. Correlation of localized residual stresses with ductile fracture toughness using in situ neutron diffraction and finite element modelling,

H. Wang, W. Woo, S.Y. Lee, G.-B. An, D.-K. Kim*,

International Journal of Mechanical Sciences 160, September 2019, 332-342 (IF 7.3, JCR 5%) https://doi.org/10.1016/j.ijmecsci.2019.06.013

27. Microstructure and mechanical anisotropy of CoCrW alloy processed by selective laser melting,

H.W. Lee, K.-H. Jung, S.-K. Hwang, S.-H Kang, D.-K. Kim*,

Materials Science and Engineering A 749, March 2019, 65-73 (IF 6.4, JCR 7.6%) https://doi.org/10.1016/j.msea.2019.02.013

26. Effect of interlayers and scanning strategies on through-thickness residual stress distributions in additive manufactured ferritic-austenitic steel structure,

W. Woo, D.-K. Kim*, E. J. Kingston, V. Luzin, F. Salvemini, M. R. Hill,

Materials Science and Engineering A 744, January 2019, 618-629 (IF 6.4, JCR 7.6%) https://doi.org/10.1016/j.msea.2018.12.078

25. Microstructure and mechanical characteristics of multi-layered material composed of 316L stainless steel and ferritic steel produced by direct energy deposition,

D.-K. Kim, W. Woo, E.-Y. Kim, S.H. Choi,

Journal of Alloys and Compounds 774, February 2019, 896-907 (IF 6.2, JCR 10%) https://doi.org/10.1016/j.jallcom.2018.09.390

2018

24. Effect of chemical dilution and the number of weld layers on residual stresses in a multi-pass low-transformation-temperature weld,

H. Wang, W. Woo, D.-K. Kim, V. Em, S.Y. Lee,

Materials and Design 160, December 2018, 384-394 (IF 8.4, JCR Q1) https://doi.org/10.1016/j.matdes.2018.09.016

23. Effect of tailored martensitic transformation in a thick weld: residual stresses mitigation, heterogeneous microstructure, and mechanical properties,

H. Wang, W. Woo, D.-K. Kim, V. Em, G.B. An, S.Y. Lee,

Materials Characterization 144, October 2018, 345-355. (IF 4.7, JCR 10%) https://doi.org/10.1016/j.matchar.2018.07.025

2017

22. Weld residual stresses in a thick plate considering back chipping: Neutron diffraction, contour method and finite element simulation study,

Y. Wan, W. Jiang, J. Li, G. Sun, D.-K. Kim, W. Woo, S.Tung,

Materials Science and Engineering A 699, June 2017, 62-70. (IF 6.4, JCR 7.6%) https://doi.org/10.1016/j.msea.2017.05.079

21. Evaluation of stress-strain relationship of constituent phases in AlSi10Mg alloy produced by selective laser melting using in-situ neutron diffraction and crystal plasticity FEM,

D.-K. Kim, J.H. Hwang, E.Y. Kim, Y.U. Huh, W. Woo, S.H. Choi,

Journal of Alloys and Compounds 714, August 2017, 687-697. (IF 6.2, JCR 10%) https://doi.org/10.1016/j.jallcom.2017.04.264

20. Mesoscopic coupled modeling of texture formation during recrystallization considering stored energy decomposition,

D.-K. Kim, W. Woo, W.W. Park, Y.T. Im, A.D. Rollett,

Computational Materials Science 129, March 2017, 55-65. (IF 3.3, JCR Q3) https://doi.org/10.1016/j.commatsci.2016.11.048

19. Effect of microstructural factors on void formation by ferrite/martensite interface decohesion in DP980 steel under uniaxial tension,

D.-K. Kim, E.Y. Kim, J. Han, W. Woo, S.H. Choi,

International Journal of Plasticity 94, July 2017, 3-23. (IF 9.8, JCR 2.2%) https://doi.org/10.1016/j.ijplas.2017.04.019

18. Molecular dynamics study of fracture toughness and trans-intergranular transition in bi-crystalline graphene,

J. Han, D. Sohn, W. Woo, D.-K. Kim*,

Computational Materials Science 129, March 2017, 323-331. (IF 3.3, JCR Q3) https://doi.org/10.1016/j.commatsci.2016.12.023

2016

17. Stress partitioning behavior of an AlSi10Mg alloy produced by selective laser melting during tensile deformation using in situ neutron diffraction,

D.-K. Kim, W. Woo, J.H. Hwang, K. An, S.H. Choi,

Journal of Alloys and Compounds 686, November 2016, 281-286. (IF 6.2, JCR 10%) https://doi.org/10.1016/j.jallcom.2016.06.011

16. Effect of interlayer sliding on the estimation of elastic modulus of multilayer graphene in nanoindentation simulation,

J. Han, S. Ryu, D.-K. Kim, W. Woo, D. Sohn,

EPL 114, July 2016, 68001. (IF 1.8, JCR Q3) https://doi.org/10.1209/0295-5075/114/68001

2015

15. Three-dimensional crystal plasticity finite element analysis of microstructure and texture evolution during channel die compression of IF steel,

D.-K. Kim, J.M. Kim, W.W. Park, H.W. Lee, Y.T. Im, Y.S. Lee,

Computational Materials Science 100, April 2015, 52-60. (IF 3.3, JCR Q3) https://doi.org/10.1016/j.commatsci.2014.09.032

14. Optimization of Flatness of a Strip during Coiling Process based on Evolutionary Algorithms,

N. Pholdee, S. Bureerat, W.W. Park, D.-K. Kim, Y.T. Im, H.C. Kwon, M.S. Chun,

International Journal of Precision Engineering and Manufacturing 16, June 2015, 1493-1499. (IF 1.9, JCR Q3) https://doi.org/10.1007/s12541-015-0198-7

13. Efficient hybrid evolutionary algorithm for optimization of a strip coiling process,

N. Pholdee, W.W. Park, D.-K. Kim, Y.T. Im, S. Bureerat, H.C. Kwon, M.S. Chun,

Engineering Optimization 47, April 2015, 521-532. (IF 2.7, JCR Q2) https://doi.org/10.1080/0305215X.2014.905551

2014

12. Numerical study of the effect of deformation history on texture evolution during equal channel angular pressing,

D.-K. Kim, K.-H. Jung, W.W. Park, Y.T. Im, Y.S. Lee,

Computational Materials Science 81, January 2014, 68-78. (IF 3.3, JCR Q3) https://doi.org/10.1016/j.commatsci.2013.05.034

11. Effects of processing parameters on elastic deformation of the coil during the thin-strip coiling process,

W. W. Park, D.-K. Kim, Y.T. Im, H. C. Kwon, and M. S. Chun,

Metals and Materials International 20, July 2014, 719-726. (IF 3.5, JCR Q1) https://doi.org/10.1007/s12540-014-4017-y

2013

10. Mesoscopic modeling of primary recrystallization of AA1050 with curvature-driven interface migration effect,

D.-K. Kim, H.W. Lee, K.-H. Jung, Y.T. Im,

Materials Transaction 54, January 2013, 81-89. (IF 1.2, JCR Q3) https://doi.org/10.2320/matertrans.M2012267

9. Crystal plasticity finite element analysis of texture evolution during rolling of fcc polycrystalline metal,

K.-H. Jung, D.-K. Kim, Y.T. Im, Y.S. Lee,

Materials Transaction 54, May 2013, 769-775. (IF 1.2, JCR Q3) https://doi.org/10.2320/matertrans.M2012346

8. Adaptive characterization of recrystallization kinetics in IF steel by electron backscatter diffraction,

D.-K. Kim, W.W. Park, H.W. Lee, S.H. Kang, Y.T. Im,

Journal of Microscopy 252, September 2013, 204-216. (IF 2.0, JCR Q3) https://doi.org/10.1111/jmi.12082

7. Prediction of the effects of hardening and texture heterogeneities by finite element analysis based on the Taylor model,

K.-H. Jung, D.-K. Kim, Y.T. Im, Y.S. Lee,

International Journal of Plasticity 42, March 2013, 120-140. (IF 9.8, JCR 2.2%) https://doi.org/10.1016/j.ijplas.2012.10.006

2012

6. Cellular automata simulation of textural evolution during primary static recrystallization of IF steel,

D.-K. Kim, K.-H. Jung, H.W. Lee, Y.T. Im,

Materials Science Forum, December 2012, 615-618. (SCOPUS) https://doi.org/10.4028/www.scientific.net/MSF.702-703.615

5. Friction measurement by the tip test for cold forging,

K.H. Jung, H.C. Lee, D.-K. Kim, S.H. Kang, Y.T. Im,

Wear 286-287, May 2012, 19-26. (IF 5.0, JCR Q1) https://doi.org/10.1016/j.wear.2011.05.031

4. Sustainability issues of research and development of forging,

Y.T. Im, S.K. Hwang, D.-K. Kim, H.M. Baek, W.Y. Park, J.W. Lee, H.S. Joo, J.M. Kim,

Journal of Achievements in Materials and Manufacturing Engineering 54, February 2012, 147-158. (SCOPUS) https://yadda.icm.edu.pl/yadda/element/bwmeta1.element.baztech-1cbc4104-f4f0-4479-b12e-05a15bef3508

2011

3. Effect of initial microstructure on mechanical properties in warm caliber rolling of high carbon steel,

Y.S. Oh, I.H. Son, K.-H. Jung, D.-K. Kim, D.L. Lee, Y.T. Im,

Materials Science and Engineering A 528, July 2011, 5833-5839. (IF 6.4, JCR 7.6%) https://doi.org/10.1016/j.msea.2011.04.016

2. A continuous hybrid process for manufacturing high-strength low carbon steel,

S.K. Hwang, Y.G. Jin, H.M. Baek, D.-K. Kim, I.H. Son, Y.T. Im,

Steel Research International, special issue, March 2011, 314-319. http://hdl.handle.net/10203/102596

2008

1. Experimental study of miniaturized tip test,

P. Chauviere, K.H. Jung, D.-K. Kim, H.C. Lee, S.H. Kang, Y.T. Im,

Journal of Mechanical Science and Technology 22, June 2008, 924-930. (IF 1.6, JCR Q3) https://doi.org/10.1007/s12206-008-0211-5