Please note these instructions are for customers using the Spybike SIM card provided with each Spylamp purchase. If you choose to use the SIM of another network provider, please choose Spylamp2 - Third Party Sim
Inside the Spylamp2 box you should find :
Inside the box are two seatpost clamps. The smaller clamp will fit standard road-bike 27.2 mm seatposts. For larger seatposts (mountain bike) you can use the larger seatpost clamp and cut the rubber spacer as required to ensure a tight fit. It is best to affix the Spylamp to your seatpost tube with the red button facing down, and use the "torx" security screw provided to secure the spylamp to your seatpost tube.
Spylamp comes with a USB cable. Plug this into a phone charger or computer to charge your Spylamp. (Phone chargers will charge faster, computer USB outlets do not deliver much power). Approximately 3 hours should be sufficient but overnight is best.
Please make yourself a nice cup of tea or coffee and read through the steps below carefully before starting to configure your Spylamp tracker!
Please note that the set up instructions vary depending on whether you are using the SIM card supplied with your Spylamp or if you are using a SIM that you have sourced yourself. If the latter, please choose the other instructions at Spylamp2 - Third Party Sim
You can set up the tracker using either the www.spybike.com tracking page or by download the spybike app (IOS and Android app stores)
Now we need to check that Steps 1-9 above have resulted in your Spylamp being correctly configured.
If the light goes off then the Spylamp has connected to the network successfully, and is ready to be used. Please go the ‘Configuring/testing’ section of this manual for a step by step guide how to how test and familiarize yourself with the tracking functions.
If the light starts to flash regularly at 4 second intervals then the Spylamp could not connect. If this happens, please repeat above steps. If the problem persists, this indicates Spylamp cannot connect to the mobile network where you are. Please try moving to a different location.
*NB : Please note that during the normal operation of the tracker you do not need to send it messages. These setup messages is just used for testing and configuration during this initial setup process. All you should need to do for daily operation is arm and disarm the tracker using the on/off button
Now you have successfully configured your Spylamp, you can now learn more about Spylamp’s other functions.
There are 2 ways to control your Spylamp:
On the [Tracking] page you can send commands to your tracker. These are SMS messages that are sent from our server to Spylamp that are useful during setup and to arm/disarm remotely.
Make sure you remember to disarm your Spylamp when you return to your bicycle or you will set the vibration sensors off when you start to ride!
You can also disarm remotely - see section below.
There is a small gold flat reset button under the lens. Pressing this will reboot the tracker and force it to re-connect to the network. It will also cause the tracker to show the green connection LED light so that you can check your network connection.
During the day to day use of your Spylamp, you will not need to to send commands to your Spylamp.
Just arm and disarm it using the on/off button (holding down for 5 seconds)
However occasionally you may need to change settings. You can do this by going to the [Trackers] page on spybike.com by clicking the [Configuration] tab or by using the mobile app
It is important to note from the outset that to save battery life, Spylamp is not normally connected to the mobile network
Spylamp will not receive your SMS messages immediately unless you ‘wake it up’ by turning the light on and off (red button) or by pressing the gold reset button.
If you are not physically with your Spylamp, please note that Spylamp periodically ‘wakes up’ every 6 hours and will check to see if it has received any commands.
If no commands have been received, it will stay awake for 5 minutes and then it go back to ‘sleep’ to conserve battery life. This awake period is extended by 5 minutes every time a command is received. You can customize all these time periods by sending commands to your Spylamp but we recommend the defaults.
You can click on the [Configuration] tab and click [Arm]. This means that if the worst happens, and your bicycle got stolen and you forgot to activate your Spylamp, you are still able activate it and find its location. You should note though that this is not as reliable as using the hardware directly to arm because SMS messages may be delayed or lost. Also they will not be received until the next wake up (trackers wakes every 6 hours to check for messages)
whereareyou - Send me the current GPS location
settings - Send you common settings as stored in tracker memory
gprssettings - Send you common network settings as stored in tracker memory (APN, User etc)
reset - Reset to factory settings.
setwakeup - How often should the device wake. i.e. setwakeup 6 hours
setwaketime - How long the tracker stays connected after waking setwaketime 5 mins
setstatus - How often the tracker should 'check in'. i.e. setstatus 1 days
checkbattery - How much charge does the battery have left
arm/disarm - Turn the vibration sensor on or off
upload - Upload the GPS location once to the website
UPPER or lower case is not important but ensure there are no leading or trailing spaces
The setwakeup, setwaketime and setstatus messages are denominated in seconds, minutes, hours or days. e.g. setwakeup 6 hours, setwaketime 5 minutes, setstatus 7 days (or you can abbreviate setwakeup 6 h, setwaketime 5 m, setstatus 7 d).
We have listed all the commands (including some less common commands) at the end of this manual in the Appendix.
If your bicycle is stolen and the tracker was armed, you will receive a message to your phone as soon as vibrations are detected (if you have not activated the vibration sensor, you should go to the configuration page and click the [Arm] button).
The Spylamp will then obtain a GPS lock and begin uploading its location to the online tracking service. By default, it will upload its location every 20 seconds.
You can look on the website and you will see a red line leading from where your bicycle was stolen to where it was taken to.
The Spylamp will continue to upload its location until 5 minutes after vibrations have stopped. So, if your thief gets home and puts the bicycle in the garage, 5 minutes later, it will then go back to sleep.
If the thief then rides your bike again tomorrow, you will receive another text, notifying you that it is on the move and then it will start tracking again. This will continue each time the thief uses your bike.
This is useful in case your bicycle is taken to a block of flats or placed somewhere where it cannot get a clear GPS signal and you are unable to pinpoint exactly where it is. The next time they ride your bike, you are notified straight away and you will be able to see where they go.
While the bike is not moving (asleep) it will enter low power mode and can last like this for weeks or months depending on the battery remaining.
If you send the tracker a SMS while it is asleep, it will respond to the text the next time it wakes or the next time the thief moves the bike or uses the bike light.
*NB : The tracker is completely disconnected from the mobile network until it wakes up.
SMS text messages (sent via the website) are sometimes not responded to straight away for a number of reasons :
*NB an easy way to ensure the tracker is connected when you want to change its configuration is to switch the light on and off. Wait 30 seconds to ensure that the tracker has connected to the network and then send it a SMS. When the message arrives the small green LED light will blink once.
Always check you have credit on your SIM card
You can send the SMS command flash to flash the light. This may be useful to test the tracker and even to find it in the dark. It is also a good way to check if the Spylamp is receiving your SMS even if it is not replying (ie you have no credit on your SIM card)
The tracker contains a lithium ion battery. This battery, when fully charged, should be enough to run the tracker for months. It is best to keep it well charged.
There are a number of factors which affect battery life, including how much you use the light, the network signal strength and the wakeup interval. See the SpyLamp section on the website setup page for more details.
You can see how much battery is left with the command checkbattery
If the battery is below 3.35 v and you attempt to switch the light on, the light will flicker and switch back off. It is time to charge the battery. Please use the charger provided.
Replacement batteries are available to purchase from www.spybike.com
You can use the tracker as a light like a normal bike light. Please note that will use more battery. You can check your battery level online on the tracking page (Choose battery view) or by sending the SMS checkbattery to your Spylamp.
The tracker can download new software from the online web server. This is useful for upgrading the tracker, fixing issues and making enhancements.
To download the latest version, send the text download
To download a specific version, send the text like download 1.3.0.1 (the version you want)
You can also download new software using the reset button and the light button.
Downloading takes approximately 5 minutes during which time the light will flicker and flash to indicate it is working. After it has finished, send the text settings to check the version that is running.
Please send emails to support@integratedtrackers.com
whereareyou - Send me the current GPS location
settings - Send you common settings as stored in tracker memory
gprssettings - Send you common network settings as stored in tracker memory (APN, User etc)
reset - Reset to factory settings.
setwakeup - How often should the device wake. i.e. setwakeup 6 hours
setwaketime - How long the tracker stays connected after waking setwaketime 5 mins
setstatus - How often the tracker should 'check in'. i.e. setstatus 1 days
checkbattery - How much charge does the battery have left
arm/disarm - Turn the vibration sensor on or off
upload - Upload the GPS location once to the website
help - Send me some common commands to remind me
setstatusmode- ALL, WEB or SMS. Do you want a daily upload, SMS or both (default both)
flash - Flash the light
networkinfo - Send me local cell information for my mobile tower. Useful when you can get a GPS lock
cellinfo - Send me local cell information for all surrounding mobile towers. Useful when you can get a GPS lock
setdebug on/off - Causes the tracker to flash when it receives a text. Only for testing
setsensitivity - (3-30). 3 = highest sensitivity, 30 = lowest. Default = 6 ie setsensitivity 6
GPRS tracking commands (these are commands relating to your tracker connecting to the network)
setgprsinterval - Set the time in between tracking positions. ie setgprsinterval 20 seconds
download - Download a new version of firmware to the tracker ie download latest
These instructions are valid for the tracker at the time of writing. You can download new versions of software to your tracker from time to time when they are released. Because of this, specific functions may be added or changed.