Tools & Materials

1. Call Miss Utility at 811. Have underground utilities marked. Wait until you get a positive response email before starting work. 

2. Identify the location(s) for your well(s). Each well will drain 6 - 8 feet in diameter around the well. Try to locate them in low spots so that water naturally flows to the well. 

3. Start the well by digging as deep as possible with your shovel. This will allow you to identify any shallow unmarked lines (private utilities, irrigation etc...) and roots. It will also give you a good "pilot hole."

4. Put the auger in your hole, and turn it, filling the auger with soil. 

5. Empty the auger into the wheelbarrow. 

6. Repeat steps 4 - 5 until the handles of the auger are on the ground. Resist the temptation to stop before the handles touch the ground. Adding a new pipe too soon will make drilling harder. 

7. Using a pipe wrench or channel locks remove the auger head from the auger. If doing this with a helper, have them stanbd on the handles and use a single wrench. If you're doing it by your self, use two wrenches. 

8. Thread a coupling onto the auger handle.

9. Thread a pipe extension onto your coupling.

10. Thread the auger head onto the pipe extension.

11. Lower the auger into the hole. Don't just drop it as this can bend the auger head. 

12. Repeat steps 4 - 11 until you reach water, installing one pipe extension at a time. Avoid stopping before you reach water or the well may be ineffective. You'll begin to hear water when you lower the auger in the ground. Keep going, if possible. At some point the soil will be wet enough that the sides of the well collapse as soon as you remove the auger and soil will fall out of the auger head. This is your stopping point. In Hampton Roads, this is typically 15 - 25 feet deep. 

13. Fill the hole with gravel, to a height slightly higher than the surrounding turf to allow for some settling. More settling may occur over the next few weeks. Refresh the rock as needed. 

14. If you're installing a drainage grate, do so after settling as stopped. I prefer to leave the well without a grate, unless draining an ac condensation line. 

WARNING: Be cautious as you start to get to moist soil and / or water. The suction can make it difficult to remove the auger. If the auger starts to "hydro lock", fill the auger less full before dumping and lift the auger out with a twisting motion.

You may hit impassable obstacles such as large roots or construction debris. If you, fill the hole in and move over a few feet to start again. Having the gas auger is handy here because restarting a hole is much faster. 

If you need more information, or if you don't feel comfortable doing it yourself, call us today!

Fescue & St. Augustine lawns are both very vulnerable to summertime fungal diseases. Managing disease is an important part of maintaining these lawns. 

Dreamlawns offers a 5 application program, that protects against both fungal diseases turf damaging insects (such as grubs and fall armyworms), and has a light nutrient package to help your lawn recover from and resist disease. We recommend this plan to all Fescue & St. Augustine customers. 

There are also great D.I.Y. options. The plan below will provide protection against both issues, if the directions are carefully followed. 

Notes:

• You can omit the Acelepryn G applications if you are not interested in insect control, but keep in mind that doing so will leave your lawn vulnerable to insect damage.

• Acelepryn G WILL NOT control non-turf damaging insects, including fleas, ticks, mosquitoes, ants, waterbugs (American cockroaches) or German cockroaches. 

• Acelepryn G will reduce white grubs, but reducing white grubs WILL NOT reduce mole populations. Please do not apply Acelepryn G as a method of reducing moles. 

• Please carefully read and follow all label directions. Using any pesticide in a manner inconsistent with its label is a violation of federal & state law. Acelepryn G Label Headway G Label Eagle Fungicide Label

• Please closely follow our watering recommendations for your turf type. Fungicide applications will not allow you to overwater your lawn. 

• The application program outlined above is similar, but not identical to Dreamlawns' Turf Damaging Insect & Disease Control Program. 

• Dreamlawns makes no warranty or guarantee as to the effectiveness of any self applied program.  

• Please call us if you see signs of disease or insect damage on your lawn. 

Plugging is the process of planting small pieces (plugs) of grass and is an economical way to establish expanding grasses such as Bermuda, Zoysia and St. Augustine. These grasses are difficult or impossible to establish from seed and sod can be rather expensive. Plugging is a great DIY option for homeowners seeking to establish one of these grasses without the expense of sod. It takes 1 - 2 years to establish Bermuda or St. Augustine and 2 - 3 years to establish Zoysia by plugs. 

Installation steps:

1. Measure the planting area. Before you can order plugs, you'll need to measure the area to determine how many plugs that you'll need. You can use a tape measure for small areas, but large areas are more easily measured with a wheel or an online measuring tool such as Findlotsize. 

2. Order your plugs. Plugs are planted in a grid pattern with 8 - 18 inches between each plug. We usually plant them about 12 inches apart, so 100 plugs would cover about 100 sq-ft. 

Caring for your plugs

Watering - 

The initial goal is to keep the soil wet to a depth of 6 inches, but not waterlogged. As the plugs root, we'll water less frequently but more heavily. 

Water your grass plugs 10 - 15 minutes twice a day for 14 days.

On day 15, change to watering once a day for 15 minutes. Maintain that for 7 days.

On day 22 test for rooting by gently pulling on a plug; it should show new runners and resist being uprooted. If the plugs are rooted, reduce watering to twice a week and increase time to 30 - 45 minutes. Maintain that watering schedule until the end of summer.

If yellowing or browning occurs at any step, go back to the last step and call us asap. Watering times are approximate and may change significantly due to sprinkler type and layout. Adjust time as needed to keep soil damp but not waterlogged. 

Disease - 

The plugs will be highly vulnerable to fungal disease for the first few weeks. If Dreamlawns is not treating the lawn for disease, we strongly suggest that you self treat using Headway G at a rate of 4 lbs per 1,000 sq-feet of turf. Treat as soon as the plugs are installed and repeat in 3 - 4 weeks. See the Fungicide & Damaging Insect Treatment section above this one for more information. 

Mowing - 

Wait until the plugs have established and grown to at least 3-4 inches in height before mowing. That will usually take about 3 - 4 weeks. Ensure your mower blades are sharp before the first mowing to avoid damaging the new grass plugs and mow at the highest setting for the first mow. After the first mowing, reduce mow height to 3 - 3 1/2 inches. 

Weeds - 

Weed populations will likely rise over the first few weeks. We won't be able to treat weeds until the plugs have been mowed 3 - 4 times, so approximately 6 - 8 weeks after installation. We'll regain control over weeds after the plugs are well established.

Please keep a close eye on the plugs. They'll be very vulnerable for the next few weeks. Please let us know ASAP if you see any yellowing or browning.