Over the last couple of years, we have been trying to get the thing to go and stop in a straight line, turn in when I ask it to, and not shake my fillings out going flat out....Oh, and accelerate flat out without coughing and sneezing at about 6000 rpm.
Part 1, the Back End.
The rear suspension is based off a Jaguar Mk X from the early sixties - think very early E Type. So independant with inboard brakes and a lsd. Unfortunately, when it was built the rearward locating bars were put in straight rather than angled to a line the same as the pivots on the diff.
This meant that as the rear wheels went up, they steered! This was a bit iffy and put big loads on all the bearings - which explained why they were knackered.
So, based off what I think it was supposed to be like and a lot of measuring, we made new links, rebuilt the hubs and renewed all the bearings - it takes a lot less time to type than to do!
At the same time, we dropped the diff down 75mm to get better angles on the driveshafts. The final job was to add an anti roll bar to keep everything on an even keel through corners.
Finally, the full exhaust system didn't fit anymore!! So, we asked Dot Worx of Bury St Edmunds to modify what we had and they did a really good job. Quiet enough (just!) for circuit work but looking and sounding great - much easier to remove for those days you just have to run loud as well.
Part 2 - the Front End
Next was the front end. It was all original 1976 Capri 1600L from what I could tell. All a bit wibbly-wobbly when on the move!
How to improve this while keeping everything looking period was the challenge. The answer was Group 4 Escorts. In the seventies, this was pretty much de-rigeur on the stages and circuits, but of course nothing fits a Capri.
So, after much cutting, bending and welding, we had a set of torsion bars to keep the front wheels in line, some pretty basic Group 4 struts and some cheap but actually not too bad brakes on the front.
The struts gave us the chance to get the front ride height a bit better and have a bit more damping control - the old ones were absolutely shot!
Part 3 - Fuelling.
One of the most annoying things when using the Capri has been the cutting out on long drag starts when showing off. We we went to Snetterton we also had starvation around the big right handers.
This was never a problem in Jersey as the hills don't have long corners and the going is very point & squirt.
I did a lot of digging on the carb - Holley stuff has so many variations; did you know they need different floats if you want to actually go around left AND right hand corners quickly??
We put in extended jets and angled floats as well as increased the fuel hose right up to the carb. Didn't make any difference, the problem was more about fuel delivery dropping off I reckon.
Having looked at some other cars - especially the bonkers MK2 Cortina with the blower, I decided to come up with a swirl pot system and add foam to the tank. We also put in a second pump to feed from the pot and return the overflow from the front to the back.
This was actually the simplest of the recent projects as I just had to find locations and routes for everything. Adding new access plates in the tank was interesting, but it all seems to have come together nicely.
Part 4 - The Blower
After last year's events I took the blower off to check the base gaskets in case this was the cause of the cutting out at high revs. The gasket was fine, but I did find that the blow off valve was not in good shape. There was also some play in the rotors, so I dropped it off to Nigel Jenkins at UK Blowers - my blower guru!
That turned into a full overhaul - well, after 13 years I couldn't complain. That all went back on quite nicely! Nigel does a good job!
Part 5 - Wheels and tyres
We had a bit of a glitch last year when we couldn't run at Prescott hill on slicks. The nice man at Kop also suggested it might be an idea to run road tyres on the road past their police station while returning down the hill.
So, trying to find suitable tyres for this think that fit and don't look small under the arches was a real challenge.
After much measuring , remeasuring, scouring ebay making wooden bucks and generally pulling my hair out, we found some 40 year old Imahge rims with the right centres and ordered some bespoke barrels from SRR Wheel Hardware. this gave us 16" on the front and 17" on the back, but with the all important width we wanted. Nangkang had some shop soiled tyres in the back of their UK warehouse so we nabbed those and, after a little felling, they fit.
Looks a bit Wacky Racers, but I quite like it!