CAD COLLECTION

0002

Part 002 started out as a rectangle and then with three rectangular cut outs using Extrude cut out and with a hole cut out at the heart of the part.

0004

part 004 consists of two circles that are connected by two lines using the relations commands such as tangent and coincident relationships. and then extruded. There are fillets on the edges of the part.

0006

0006 consists of rectangular command, circular commands and oval commands and Extrude cut .

1001

1001 was fully sketched out with fillets the tail has a 45 degree cut out. and then using hole- wizard i used a tapped hole and used Extrude cut- "up to surface"

V1010

V1010 is a screw by using "appearances" to create an image of threads. this part is very simple to create it started out using circle command and then extrude and fillet at the end to create a dome shape

A1005

A1005 started by sketching and extruding a circle. Then at every 90 degrees there is a circle with with different diameters and at the ends of each circle is a line connecting to the edge of the part to create an oval shape cut out.

C1002

C -1002 is a screw without the threads it the way i created this was Sketching half the screw and then revolve around a construction line then I used the chamfer command to smooth out the sharp edges. and lastly created a hole at the center of the head of the screw.

tutorial block

This part was created by making an extruded 12x12 square with a extruded holes in the center. Next we went to the back of the part and used the shell command.

v1001

V1001 started out as a long rectangular block with two rectangular cut outs. four stems for bracketing, and a circular hump with a hole cut through it using hole wizard. There are a total of seven circular holes.

0006

0006 started out as a sketch of an "L" and then Extruded. There are two triangular cut-outs on the upward side of the part. Next i created a triangle that connects from the top and bottom of the part at the center. And lastly there are two symmetrical holes on either side of the part.

1006

1006 started by sketching a circle and extruding it. Then sketching a slightly larger circle extruding that to certain length and then fillet that by 0.06in.

0003

0003 is a extruded rectangle with fillets on the edges. And in the center are two small holes and a larger hole in between the smaller holes. All three holes were created by using Hole wizard.

V1002

V1002 is complicated part, it has a mixture of sketches, Extrusions and cut outs and fillets.

V1005

V1005 started by sketching and extruding a circle and then doing the same operation at the bottom of the previous circle. After that I created thread on the top half of the part then adding a rectangular slit of the thread.

cs-1007

cs-1007 was created by sketching out half the part and then revolving it around an axis

0001

0001 is relatively easy, it starts out as rectangular block and then sketching another block inside a The extruded box, then Extrude cut the sketched box through the part. Next there is another rectangular cut-out within the previous cutout but in a horizontal manner. And lastly there are two holes placed on the top face of the part.

CS-1003

CS-1001

CS1004

Cs-1005

Base

A very complex part, That deals with a lot of sketching's, relations, circular commands and extrusion cuts.

Lower Jaw

The lower Jaw was sketched out by creating an L shape, then from the top down I created a stair case of 9 horizontal lines and 9 vertical line. Then I used the Equal relationship to make each line the same length. Then I Sketched two symmetrical circles At a distance.

Upper jaw

The upper Jaw was sketched out by creating an L shape, then from the top down I created a stair case of 9 horizontal lines and 9 vertical line. Then I used the Equal relationship to make each line the same length. . Then I Sketched two symmetrical circles At a distance.

Upper Jaw support

The upper jaw support was first started out as a sketch of a box with two square cut outs at the bottom edge and then Extruded. After I selected the front plane to sketch a half circle and then extruded to a certain number. Next Comes a series of cuts and fillets for the functionality of the assembly.

Vice support

The vice support started as a series of circles with different proportion to form a opened an square with Fillets and different relations such as tangent and coincident. Next on the top view i created a extruded circle going down to form a by pass for the Adjustment screw. On the front plane i created another extruded circle on the left side of the part for the pad lock. On the bottom are two circles That are for screws to secure to the base.

Pad Lock

The pad lock was roughly Sketched out and then Extruded by the mid-point. And last a circular cut out.

Adjustment Screw

i created this was Sketching half the screw and then revolve around a construction line then I used the chamfer command to smooth out the sharp edges. and lastly created a hole at the center of the head of the screw. and with the addition of threads and knurls.

Handle

The Handle in its Entirety was sketched Half way and revolved around an axis.

Arbor Body

-------------No Description--------------

A1006

This part started out by sketching and extruding a circle. Then at every 90 degrees there is a circle with with different diameters and at the ends of each circle is a line connecting to the edge of the part to create an oval shape cut out.

A1007

A1007 Is a Extruded circle with Horizontal Cut outs on the ends of the rod using circular pattern to create an interesting design.

A1008

A1008 is a Extruded circle with one fillet on one edge and on the bottom Face was cut out to form a cap for the A1007.

A1003

Al003 Consists of two Extruded Circles and on the first circular body i created A set of teeth using the Extrude cut command and circular pattern to form around the body. to compliment the teeth I blended in between the teeth for aesthetics. lastly I Sketched out two circles on the top face and front face of the part for screws.

A1002

A1002 Started out as a rectangular Sketch then Extruded. Next we Added twenty two individual teeth for Functionality for the assembly

A1004

A1004 Is a Extruded Rectangle with four filleted Edges and four large holes near the fillets. Next In the center is a rectangular cut out with All around filleted edges with two symmetrical tapped holes, using Hole wizard

Gibb Plate

The Gibb Plate Is a rectangle that's been Extruded.