black flcan wire to 2 wire purple wago on high current
Panic Mode If you are threatened in or near your vehicle, you can attract attention by triggering the system with your remote control. Press {5 for approximately two seconds to enter Panic Mode. In Panic Mode, the horn will honk and the parking li~ts will flash for 30 seconds. To stop Panic Mode at any time, press (5, or {5 on the remote control.
aux button
Silent Mode™ and an optional auxiliary function are controlled by pressing . Silent Mode works by pressing for less than one second before locking or unlocking. An optional auxiliary function such as trunk release may be controlled by pressing and holding for approximately two seconds.
https://www.directeddealers.com/manuals/OG/Avital/G4105L%202016-06%20web.pdf
The thicker white wire with the fuse on it? park lights should flash, once when it's locks, and twice for unlock.. and when it's "running" they should come on constant.
https://www.the12volt.com/installbay/forum_posts.asp?tid=144905
1. Exit Valet Mode
If the LED on your antenna is solid orange or red (not flashing), the system is in Valet Mode, which disables all security and chirp functions.
To Exit: Turn the ignition key to the "On" position. Press and release the Valet button (located on the antenna/under the dash) once. The LED should turn off.
YouTube +4
2. Enable Horn/Chirp Function
The system might be programmed to be silent upon unlock.
Key Fob Toggle: Press and hold the Lock and Unlock buttons at the same time to toggle the horn/chirp function.
Function Button: Try pressing the function ("f" or "AUX") button, followed by the Lock or Unlock button.
Reddit +1
1/4 Mile of range
New, slim 4-button remote controls
Virtual Tach RPM sensing
D2D serial data interface for Xpresskit D2D modules
Flex Relays for remote start and light flash
Advanced remote start functions: Timer Start, Smart Start, RunTime Reset
https://classiccaraudio.com/remote-starters-security-systems/
vehicles
black flcan wire to 2 wire purple wago on high current
from youtube video
\https://www.youtube.com/watch?v=y7NsJOLfNkw
main ignition switch wires
yellow - orange sentry?
not white/black
black/yellow - pink ignition
white - red 12v
black/white - starter - yellow
black ground left side of dash (small penel removed) 10 mm -
FLASHLOGIC
FLCAN
FLCAN CONNECTORS PINS WIRES
SIDE ONE OF FLCAN
the 10 pin connector wires are colored thus (in order)
1. green/black LOCK/ARM (-) INPUT
2. blue/black UNLOCK (-) INPUT
3. red/white TRUNK (-) INPUT
4. brown DISARM (-) INPUT
5. purple/yellow LEFT SLIDING DOOR (-) INPUT
6. purple/black RIGHT SLIDING DOOR (-) INPUT
7. white (NC)
8. black/white STARTER (+) INPUT
9. green E-BRAKE STATUS (-) OUTPUT
10. purple/white TACH (AC) OUTPUT
the DATA MODE connector, which HAS A BLACK SHEATH AROUND THE 4 WIRES AND IS CONNECTED TO THE VIPER 4105 AND THE FLCAN
1. blue/white GWR (-) INPUT
2. white (NC)
3. black GROUND
4. red 12V (+)
SIDE TWO OF FLCAN
3 pin connector (with white wires)
1. whiteblack SECURITY LIGHT INPUT
2. white/red SECURITY LIGHT OUTPUT
3. white (NC)
3 pin connector (with yellow wires)
1. yellow/black DOOR STATUS (-) OUTPUT1
2. yellow/red TRUNK STATUS (-) OUTPUT
3. white HOOD STATUS (-) OUTPUT*
7 pin connector
1. brown/red (NC)
2. brown/yellow (NC)
3. orange/black IMMOBILIZER (DATA)
4. orange/white (NC)
5. orange SWC (DATA
6. pink/black (NC)
7. pink IGNITION (+) INPUT
6 pin connector
1. blue/red (NC)
2. blue/yellow (NC)
3. green/red (NC)
4. green/yellow (NC)
5. gray/red (NC)
6. gray/yellow (NC)
VIPER 4105V - CONNECTORS PINS WIRES 022526
VIPER 4105V left side
9 pin connector
1 LIGHT GREEN BLACK (-) 200mA FACTORY ALARM DISARM
2 GREEN/WHITE (-) 200mA FACTORY ALARM REARM
3 YELLOW (+) IGNITION OUT (TO ALARM)
4 WHITE/BLUE (-) ACTIVATION INPUT
5 ORANGE (-) 500mA GROUND WHEN LOCKED/ANTI-GRIND OUTPUT
6 BROWN (-) 200mA HORN OUTPUT
7 RED/WHITE (-) 200mA TRUNK RELEASE OUTPUT
8 BLACK GROUND
9 WHITE (+/-) LIGHT FLASH OUTPUT
Satellite harness, 4-pin connector
1 BLUE (-) 200mA STATUS OUTPUT
2 ORANGE (-) 200mA ACCESSORY OUTPUT
3 PURPLE (-) 200mA STARTER OUTPUT
4 PINK (-) 200mA IGNITION OUTPUT
5 PIN CONNECTOR Remote Start harness
1 BLACK/WHITE (-) NEUTRAL SAFETY SWITCH INPUT
2 VIOLET/WHITE TACHOMETER INPUT WIRE
3 BROWN (+) BRAKE SHUTDOWN INPUT WIRE
4 GRAY (-) HOOD PIN SWITCH SHUTDOWN WIRE
5 BLUE/WHITE (-) 200 mA 2ND STATUS/REAR DEFOGGER
6 PIN CONNECTOR Remote start, HIGH CURRENT - LOCATED AT END OF VIPER 4105V
1 RED (+) (30A) HIGH CURRENT 12V INPUT
2 PINK/WHITE OUTPUT TO SECOND IGNITION/ACCESSORY CIRCUIT
3 RED (+) (30A) HIGH CURRENT 12V INPUT
4 ORANGE OUTPUT TO ACCESSORY CIRCUIT
5 PURPLE OUTPUT TO STARTER CIRCUIT
6 PINK OUTPUT TO PRIMARY IGNITION CIRCUIT
DATA MODE CABLE
(black cable with 3 wires - red connector)
1 end plugged into FLCAN
1 end plugged into SIDE 2 of VIPER
GWR (-) INPUT - BLUE/WHITE
GROUND - BLACK
12V (+) - RED
3-pin connector - Door Lock - LOCATED ON END OF VIPER 4105V
1 BLUE (-) UNLOCK
2 EMPTY NOT USED
3 GREEN (-) LOCK
PHOTOS FROM
2008 HONDA RIDGELINE
