AIM

CONSTANT HEAD PERMEABILITY TEST OF SANDY SOIL

MATERIAL REQUIRD:

§ Permeameter,

§ Tamper,

§ Balance,

§ Scoop,

§ 1000 mL Graduated cylinders,

§ Watch (or Stopwatch),

§ Thermometer,

§ Filter paper.

PROCEDURE:

(1) Measure the initial mass of the pan along with the dry soil.

(2) Remove the cap and upper chamber of the permeameter by unscrewing the knurled cap nuts and lifting them off the tie rods. Measure the inside diameter of upper and lower chambers. Calculate the average inside diameter of the permeameter

(3) Place one porous stone on the inner support ring in the base of the chamber then place a filter paper on top of the porous stone.

(4) Mix the soil with a sufficient quantity of distilled water to prevent the segregation of particle sizes during placem ent into the permeameter. Enough water should be added so that the mixture may flow freely.

(5) Using a scoop, pour the prepared soil into the lower chamber using a circular motion to fill it to a depth of 1.5 cm. A uniform layer should be formed.

(6) Use the tamping device to compact the layer of soil. Use approximately ten rams of the tamper per layer and provide uniform coverage of the soil surface. Repeat the compaction procedure until the soil is within 2 cm. of the top of the lower chamber section.

(7) Replace the upper chamber section, and don’t forget the rubber gasket that goes between the chamber sections. Be careful not to disturb the soil that has already been compacted. Continue the placement operation until the level of the soil is about 2 cm below the rim of the upper chamber. Level the top surface of the soil and place a filter paper and then the upper porous stone on it.

(8) Place the compression spring on the porous stone and replace the chamber cap and its sealing gasket. Secure the cap firmly with the cap nuts.

(9) Measure the sample length at four locations around the circumference of the permeameter and compute the average length. Record it as the sample length.

(10) Keep the pan with remaining soil in the drying oven.

(11) Adjust the level of the funnel to allow the constant water level in it to remain a few inches above the top of the soil.

(12) Connect the flexible tube from the tail of the funnel to the bottom outlet of the permeameter and keep the valves on the top of the permeameter open.

(13) Place tubing from the top outlet to the sink to collect any water that may come out.

(14) Open the bottom valve and allow the water to flow into the permeameter.

(15) As soon as the water begins to flow out of the top control (de-airing) valve, close the control valve, letting water flow out of the outlet for some time.

(16) Close the bottom outlet valve and disconnect the tubing at the bottom. Connect the funnel tubing to the top side port.

(17) Open the bottom outlet valve and raise the funnel to a convenient height to get a reasonable steady flow of water.

(18) Allow adequate time for the flow pattern to stabilize.

(19) Measure the time it takes to fill a volume of 750 – 1000 ml using the graduated cylinder, and then measure the temperature of the water. Repeat this process three times and compute the average time, average volume, and average temperature.

(20) Measure the vertical distance between the funnel head level and the chamber outflow level, and record the distance as.

(21) Repeat step 17 and 18 with different vertical distances.

(22) Remove the pan from the drying oven and measure the final mass of the pan along with the dry soil.

ANALYSIS:

(1) Calculate the permeability, using the following equation:

K_T = QL/A*t*h

Where:

K_T = coefficient of permeability at temperature T, cm/sec.

L = length of specimen in centimeters

t = time for discharge in seconds

Q = volume of discharge in cm³ (assume 1 mL = 1 cm³)

A = cross-sectional area of permeameter (= [(π D²)/4] , D= inside diameter of the permeameter)

h = hydraulic head difference across length L, in cm of water; or it is equal to the vertical distance between the constant funnel head level and the chamber overflow level.

(2) The viscosity of the water changes with temperature. As temperature increases viscosity decreases and the permeability increases. The coefficient of permeability is standardized at 20°C, and the permeability at any temperature T is related to K20 by the following ratio:

K₂₀ = K_T (η_T/ η₂₀)

Where:

η_T and η₂₀ are the viscosities at the temperature T of the test and at 20°C, respectively. From Table 1 obtain the viscosities and compute K₂₀.

(3) Compute the volume of soil used from: V = LA.

(4) Compute the mass of dry soil used in permeameter (M) = initial mass -final mass:

M = M₁-M₂

(5) Compute the dry density (ρ_d) of soil

ρ_d = M/V

Table 1. Properties of Distilled Water (η = absolute)

Temperature (⁰C) Density (g/cm³) Viscosity (Poise*)

4

16 , 17,

.........30

*1 Poise = dyne*s/ cm² = 8/cm*s