Sensor and Modules

Ultrasonic sensor sr 04

₹100.00

AES13S1

Micro SD Card Reader Module

₹100.00

Add the desired memory to your Arduino project to store the data, Media, etc. Micro SD Card Reader Module also called Micro SD Adaptor which is designed for dual I/O voltages. The Module is a simple solution for transferring data to and from a standard SD card. The pinout is directly compatible Not only with Arduino as shown in the diagram below, but can also be used with other microcontrollers. Micro SD Card Reader Module has an SPI interface that is compatible with any sd card and it uses a 5V or 3.3V power supply which is compatible with Arduino UNO/Mega.SD module has various applications such as data logger, audio, video, and graphics.

AES13S2

IIC/I2C Serial Interface Adapter Module

₹90.00

This is a RoHS-compliant I2C Serial LCD Daughter board that can be connected to a standard 16×2 or 20×4 Character Display Module that supports 4-bit mode. All Character Modules sold on our site support 4-bit mode, and nearly all commercially available 16×2 and 20×4 line character modules support it too.

AES13S3

Blutooth hc 05

₹280.00

AES13S4

4 Road/Channel Relay Module 5V

₹230.00

5 relay modul

AES13S5

5V 1 Channel Without Light Coupling Relay

₹70.00

It is a 5V 1 Channel Without Light Coupling Relay. The relay normally open interface maximum load: AC 250V/10A, DC 30V/10A. It has a trigger current of 5mA, and module working voltage of DC 5V. Each channel of the module can be triggered by a jumper to set a high level or a low level. Fault-tolerant design, even if the control line is disconnected, the relay will not move. With status indicator: power (green), 1-channel relay status indicator (red). All module size interfaces can be directly connected through the terminal block, which is convenient and practical.

AES13S6

5V 2 Channel Relay Module

₹160.00

This is a 2 Channel 5V Relay module, that is able to control various appliances, and other equipment with a large current. It can be controlled directly by Microcontroller (8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).5V 2-Channel Relay interface board and each one needs a 15-20mA Driver Current Equipped with a high-current relay, AC250V 10A; DC30V 10A Standard interface that can be controlled directly by microcontroller (8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic) Indication LED’s for Relay output status.

AES13S7

LM2596S with SMD LED DC-DC Step-Down Power Supply

₹85.00

Input voltage: 3-40V

Output voltage: 1.5-35V(Adjustable)

Output current: Rated current is 2A, maximum 3A

Switching Frequency: 150KHz

Operating temperature: Industrial grade (-40 to +85 )

Conversion efficiency: 92%(highest)

AES13S8

XL6009 DC-DC Step-Up Converter  Booster Circuit Board

₹120.00

Non-isolated Boost converter.

It has a non-synchronous rectifier.

Low ultra-wide input voltage 3 v ~ 32 v, the best is 5 ~ 32 v working voltage range;

Low ultra-wide output voltage 5 v ~ 35 v;

AES13S9

PAM8403 Mini 5V Digital Amplifier Board With Switch Potentiometer

₹110.00

This is PAM8403 Mini 5V Digital Amplifier Board With Switch Potentiometer. PAM8403 is a small digital amplifier chip, high-definition sound quality highlights the advantages of digital chips, the circuit using the most reasonable peripheral configuration, power supply filtering is upgraded to 470uf (some sellers are less did not even 100uf capacitance).

1.6mm glass sheet, the real amplifier board did the most detailed, high-fidelity sound output 3W + 3W, is a rare good product enthusiasts amplifier, potentiometer using the original anti-meter body, potentiometer with the switch can cut off the power supply directly counterclockwise.

AES13S10

MQ-2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module

₹115.00

Operating Voltage:+5V

Preheat Duration:20 s

Analog Output Voltage:0 to 5 V

Dimension:36x20x21 mm

AES13S11

MQ-3 Alcohol Detector Gas Sensor Module

₹150.00

Power requirements: 5 VDC @ ~165 mA (heater on) / ~60 mA (heater off).

Current Consumption: 150mA.

DO output:  0.1 and 5V.

AO output: 0.1- 0.3 V (relative to pollution), the maximum concentration of a voltage of about 4V

Detecting Concentration: 0.05-10mg/L Alcohol.

AES13S12

Infrared Obstacle Avoidance IR Sensor Module

₹40.00

Detection distance: 2 ~ 30cm

Detection angle: 35 °

Comparator chip: LM393

3mm screw holes for easy mounting

AES13S13

E18-D80NK Adjustable Infrared Sensor Switch 3-80cm

₹220.00

Sensing range: 3 – 80cm.

Input voltage: 5VDC.

Current Consumption: 300mA.

Digital Output.

Cable length: 1 m.

Diffuse reflective type.

AES13S14

JoyStick Shield Module Robotics Control

₹250.00

2-Axis joystick

Bluetooth / Serial interface

I2C interface

nRF24L01 interface

Nokia 5110 LCD interface

Interface connector

Power switch to switch between 3.3 and 5V

AES13S15

Multifunction Shield For Arduino Uno

₹250.00

10K adjustable precision potentiometer.

3 x Independent push buttons.

Piezo buzzer.

DS18B20 temperature sensor interface.

LM35 temperature sensor interface.

Infrared receiver interface.

AES13S16

LCD keypad Shield

₹280.00

Provides a user-friendly interface that allows users to go through the menu, make selections, etc.

It consists of a 1602 white character blue backlight LCD.

The keypad consists of 6 keys select, up, right, down, left, and reset.

To save the digital IO pins, the keypad interface only uses one ADC channel.

The key value is read out through a 5-stage voltage divider

AES13S17

USB to RS485 Converter Adapter Support WIN7 XP Vista Linux Mac OS

₹150.00

Fully compliant USB 2.0 standard, backward compatible with USB1.1

Support System: Windows XP, Vista, Windows 7, Linux, MacOS, and WinCE5.0 drive

Baud Rate Range: 75bps – 115200bps, up to 6Mbps

Supports Plug, Play, and hot-swap ( USB side)

Better than using a CH341D chip or a similar chip to support the laptop USB port.

Communication distance up to 1.2KM

AES13S18

USB TO UART TTL 5V 3.3V FT232RL Download Cable To Serial Adapter Module For Arduino

₹200.00

Standard interface layout, compatible with a variety of Arduinos such as the Pro Mini

Original FTDI FT232 chip, stable performance

USB power has current protection, using 500MA self-restore fuse

RXD/TXD transceiver communication indicator

With power, sending, receiving indicator, working status LED indicators

Mini USB Port Connection

Support 3.3V, 5V

AES13S19

Digital Sensor  Module Capacitive Touch Switch

₹60.00

Power supply voltage(VCC): 2.0, 3, 5.5 V.

Output high VOH: 0.8VCC V

Output low VOL: 0.3VCC V

Response time (touch mode) : 60 mS

Response time (low power mode) : 220 mS

Can replace the traditional touch of a button

Four M2 screws positioning holes for easy installation

AES13S20

DHT11 Temperature And Humidity Sensor Module

₹140.00

Input Supply voltage (VDC): 3.3 ~ 5

Supply Current (mA): measurement 0.3mA standby 60μA.

Temperature measurement range: 0~50 degrees

Temperature measurement error: ±2 degrees

Humidity measurement range: 20%~95%RH

Humidity measurement error: ±5%RH

AES13S21

XH W1209 12V Digital Temperature Controller Module W/ Display and NTC Temp Sensor

₹190.00

Temperature Control Range(°C): -50 to +110

Resolution @-9.9°C to +99.9°C: 0.1°C

Resolution @all temperatures: 1°C

Accuracy: 0.1°C

Refresh Rate(s): 0.5

Supply Voltage(V): 12

Measuring Inputs: NTC10K

Cable Length: 0.5 Meter

Output Type: 1 Channel Relay Output

Capacity: 10A

AES13S22

Analog PH Sensor Kit

₹2,050.00

Module power supply: 5 VDC.

Measuring temperature: 0-50 ℃.

Response time: ≤ 1min.

pH sensor with BNC connector.

Gain adjustment Potentiometer.

Power indicator LED.

AES13S23

30A range Current Sensor Module ACS712

₹150.00

The low-noise analog signal path

Device bandwidth is set via the new FILTER pin

5 µs output rise time in response to step input current

Small footprint, low-profile SOIC8 package

2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8

Supply Voltage: 4.5V~5.5V DC

Measure Current Range: 30A

Sensitivity: 100mV/A

AES13S24

5A range Current Sensor Module ACS712

₹150.00

Low-noise analog signal path.

Device bandwidth is set via the new FILTER pin.

5 µs output rise time in response to step input current.

Small footprint, low-profile SOIC8 package.

2.1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8.

AES13S25

SIM800L GPRS GSM Module

₹350.00

TTL serial port for serial port, you can link directly to the micro-controller.

Don’t need MAX232.

Power module automatically boots, homing network.

Onboard signal lights all the way.

It flashes slowly when there is a signal, it flashes quickly when there is no signal.

AES13S26

L298 2A Dual Motor Driver Module with PWM Control

₹150.00

This L298 Based Motor Driver Module is a high-power motor driver perfect for driving DC Motors and Stepper Motors. It uses the popular L298 motor driver IC and has the onboard 5V regulator which it can supply to an external circuit. It can control up to 4 DC motors, or 2 DC motors with directional and speed control

This motor driver is perfect for robotics and mechatronics projects and perfect for controlling motors from microcontrollers, switches, relays, etc. Perfect for driving DC and Stepper motors for micro mice, line-following robots, robot arms, etc.

An H-Bridge is a circuit that can drive a current in either polarity and be controlled by Pulse Width Modulation (PWM).

Pulse Width Modulation is a means of controlling the duration of an electronic pulse. In motors try to imagine the brush as a water wheel and electrons as the flowing droplets of water. The voltage would be the water flowing over the wheel at a constant rate, the more water flowing the higher the voltage. Motors are rated at certain voltages and can be damaged if the voltage is applied to heavily or if it is dropped quickly to slow the motor down. Thus PWM. Take the water wheel analogy and think of the water hitting it in pulses but at a constant flow. The longer the pulses the faster the wheel will turn, the shorter the pulses, the slower the water wheel will turn. Motors will last much longer and be more reliable if controlled through PWM.

AES13S27

AES13S27

TTP223 1-Channel Capacitive Touch Sensor Module Red Color

₹25.00

The TTP223 1-Channel Capacitive Touch Sensor Module Red Color is based on a touch-sensing IC (TTP223) capacitive touch switch module. A capacitive touch sensor module based on the dedicated TTP223 touch sensor IC. The module provides a single integrated touch sensing area of 11 x 10.5mm with a sensor range of ~5mm.

An onboard LED will give a visual indication of when the sensor is triggered. When triggered the output of the module will switch from its idle low state to high (default operation). Solder jumpers allow for reconfiguring its mode of operation to be either active low or toggle output.

TTP223 Capacitive Touch Sensor Module. The TTP223 is a touchpad detector IC replicating a single tactile button.

The TTP223 is a touchpad detector IC replicating a single tactile button. This touch detection IC is designed for replacing traditional direct button key with diverse pad size.

Trigger-setting mode: (1- > Short ; 0- > No Short):-

AB=00: No-lock High TTL level output;

AB=01: Self-lock High TTL level output;

AB=10: No-lock Low TTL level output;

AB=11: Self-lock Low TTL level output;

AES13S28

AES13S28

TEC1-12707 12V 7A TEC Thermoelectric Cooler Size：40x40MM

₹220.00

Model number: TEC1-12707

Operating Voltage: 12V

Maximum Voltage- Umax (V) : 15V

Maximum Current- Imax (A) : 10A

Maximum Power : 120W

Power Cord: 25cm

AES13S29

AES13S29

LoRa module RFM95W-915 MHZ

₹700.00

min Supply voltage: 1.8.

Max.  Operating voltage: 3.7

Min. Operational temperature range -20

Max. Operational temperature: +70

Max. RF Input Level:+10 d

AES13S30

Hall Effect Sensor, Position, Digital, Bipolar,

₹150.00

Product: SS41 Hall Effect Sensor, Position, Digital, Bipolar, SS40 Series

Supply voltage (V): 4-24

Supply current (OUTPUT ON): 10.0

Output current (A): 20

Output leakage current (A):10.0

Rise time (10% to 90%): 1.5

AES13S31

AES13S31

NRF24L01 2.4GHz Wireless Transceiver Module

₹85.00

Features of NRF24L01 2.4GHz Wireless Transceiver Module:-

NRF24L01 is a universal ISM band monolithic transceiver chip works in the 2.4-2.5GHz

Wireless transceiver including: Frequency generator, enhanced type, SchockBurstTM, mode controller, power amplifier, crystal amplifier, modulator, demodulator

The output power channel selection and protocol settings can be set extremely low current consumption, through the SPI interface

As the transmit mode, the transmit power is 6dBm, the current is 9.0mA, the accepted mode current is 12.3mA, the current consumption of the power-down mode and standby mode are lower

Built-in 2.4GHz antenna, supports up to six channels of data reception

Size: 15 x 29mm

Low operating voltage: 1.9-3.6V

125 channels, multi-point communication and frequency hopping to meet the communication needs

High Rate: 2Mbps, as air transmission time is very short, greatly reducing collision phenomena in wireless transmission (air transfer rate of software setting: 1Mbps or 2Mbps)

Low power consumption: When the answer mode communication, fast air transmission and start-up time, which greatly reduces the current consumption

Low application cost: NRF24L01 integrated part of all high-speed signal processing related to RF protocol, such as automatic retransmission of lost packets and automatically generating response signals, etc.

NRF24L01 SPI interface: hardware SPI port, MCU I/O ports

Internal FIFO is compatible with a variety of microprocessor interfaces, micro-controller is convenient

AES13S32

AES13S32

ISD1820 Recording Module Voice Board With On Board Mic and Loud Speaker

₹190.00

The package includes an 8 Ohm 0.5W speaker and cable which can be connected directly to the modules speaker output.

Buttons control audio recording method of operation

REC Button: record button, you can press and hold the recording, release the button to stop recording;

RLAYE Key: trigger mode playback, press will play this whole speech;

PLAYL Key: jog mode playback, press and hold until playback, release to stop playback;

RPL Jumper: loop mode control, loop playback;

FT Jumper: direct control, microphone voice through the speaker can playback;

AES13S33