離陸からクルーズを経て、ディセント・APP 及び着陸後のシャットダウンまでの一連の手順はこちらの方が分かり易く書かれてあります。（ForumサイトにあったPDFです）
PMDG 737 Cold & Dark to Secure Check list
Preflight Procedure
Ground Cart CONNECT
Battery Switch GUARD CLOSED
Standby Power GUARD CLOSED
Ground Power ON
IRS
IRS OFF THEN NAV
CDU-FMC
POS INIT Page SET IRS POS LINE
Doors
Open Doors AS NEEDED
Air Stairs IF NEEDED
Emergency Exit Lights
Emergency Exit Lights Switch GUARD CLOSED
Passenger Signs
No Smoking/Chime AUTO or ON
Fasten Belts AUTO or ON
Heat & Anti-Ice
Window Heat ON
Probe Heat OFF
Wing Anti-Ice OFF
Engine Anti-Ice OFF
Air Conditioning Panel
Check Trim Air ON
Recirculation Fan Switches AUTO
Air Conditioning Pack Switches AUTO or HIGH
Isolation Valve Switch OPEN
Engine Bleed air switches ON
Cabin Pressurization Panel
Flight Altitude Indicator Set CRUISE ALTITUDE
Landing Altitude DESINATION FIELD ELEVATION
Lighting Panel
Logo AS NEEDED (ON)
Position Lights AS NEEDED (ON)
Anti-Collision OFF
Wing Illumination AS NEEDED
Radio
Contact ATIS NOTE QNH, RWY IN USE, TEMP
VHF Communications Radios SET
VHF Navigation Radios SET
Contact ATC for clearance SET TRANSPONDER CODE, NOTE CLEARNED ALT
Transponder Panel SET (Squawk Code) (Transponder to Standby)
Set Up CDU-FMC
IF YOU NEED A WALK THOUGH PMDG NGX FCOMv1 page 79-81(Set PAX/Fuel loads first)
EFIS Control Panel
Minimums Reference Selector RADIO or BARO
Minimums Selector SET DECISION HEIGHT
MCP (Mode Control Panel)
Course SET
Auto Throttle ARM
Flight Director Switches ON (MOVE THE PILOT FLYING FD TO ON FIRST)
IAS SET V2
Initial Heading SET
Initial Altitude SET
Bank Angle Selector AS NEEDED
LNAV AS NEEDED
VNAV ARM
APU
APU START
Fuel Panel
All Fuel Pumps ON
Doors
Exterior Doors CLOSE
APU
APU Generator switches ON
APU Bleed Air Switch ON
Ground Power
Ground Power OFF and REMOVE
Overhead Panel
Electric Hydraulic Pump Switches ON
Anti Collision Light Switch ON
YAW Damper Switch ON
Flight Deck Panel and Control Stand
Speed Brake Lever DOWN DETENT
Trim SET
Parking Brake ON
Auto Brake Select Switch RTO
Engine Display Control Panel ON
Push Back and Start Engines
CDU Push back, Set up as needed START (Follow ground crew prompts)
Engine Ignition Selector BOTH(Or Select to match the engine starting)
Air Conditioning PACK Switches OFF
Engine #2 Start Switch GRD
When N2 RPM is at 25% ENGINE START LEVER = IDLE
Wait for Engine 2 Starter CUT OUT
Engine #1 Start Switch GRD
When N2 RPM is at 25% ENGINE START LEVER = IDLE
Wait for Engine 1 Starter CUT OUT
Before Taxi Procedure
Generator 1&2 Switches ON
Probe Heat ON
Wing Anti-Ice AS NEEDED
Engine Anti-Ice AS NEEDED
Pack Switch AUTO
Isolation Valve AUTO
APU Bleed Air Switch OFF
APU Switch OFF
Engine Start Switches CONT
Set Flaps 5 (or as needed)
Lower Engine Display OFF
Light AS NEEDED
Taxi
Taxi and Hold Short
When Cleared for Takeoff
Strobe lights ON
Fixed landing Lights ON
Transponder mode TA/RA
Line up
Align Aircraft On Runway
Takeoff
Advance Thrust Levers to 40% N1 STABILIZE
TO/GO ON
At VR ROTATE
After Takeoff
Positive Rate of Climb GEAR UP
At 400ft Radio Select Roll Mode SELECT (OR IF LNAV/VNAV ARMED = CMD A ON)
At Acceleration height FLAPS UP ACCORDING TO FLAP RETRACTION SCHEDULE
After Flaps and Slats Retraction VNAV/LNAV (Switch on if not armed or other AP Options)
CMD A (Autopilot) ON
Auto Brakes OFF
Engine Start Switches OFF
Landing Gear OFF
Climb
Altitude SET ASSIGNED ALT
Altitude Change PRESS ALT CHANGE
At Transition ALT BARO STD
At 10,000FT LANDING LIGHTS OFF
5 Miles before Descent
SET ALT AS NEEDED (Option, GS High )
2 Miles before TD
Option If using FSX ATC Ask for New Lower Cruise ALT, get max you can.
Descent
CDU-FMC VREF FLAPS 30% SELECT/ENTER
NAV Radios ILS Frequencies SET (FO as well for Auto land)
MCP Course of RWY SET
If Using HGS SET RWY ELV/ RWY LENGTH
At Transition ALT BARO STD
Auto Brakes SET TO 2 or AS NEEDED
Minimums SET RADIO 100ft
At 10,000ft LANDING LIGHTS ON
Map Range 10NM or AS NEEDED
At Flaps Up Speed FLAPS 1
Speed Brakes USE WHEN REQUIRED
Approach
Before Intercept VOR/LOC ARM
Turning onto Localizer FLAPS 5
Localizer Captured APP ON
CMD B ON (FOR AUTOLAND)
IAS SET VREF +5
Engine Start Selectors CONT
At Flaps 5 Speed FLAPS 15
Landing Gear DOWN
At Flaps 15 FLAPS 30
Speed Brakes ARM
Landing
At Touch Down THRUST REVERSERS ON
80 Knots THRUST REVERSERS OFF
Auto Brakes DISENGAGE
Auto Pilot if On OFF
After Landing Procedure
Speed Brakes DOWN
APU START
Probe Heat OFF
Landing Lights OFF
Taxi Lights ON
Position Lights ON STEADY
Engine Start Selectors OFF
Auto Breaks OFF
Flaps UP
Transponder ALT or STANDBY
Shutdown Procedure
Parking Brake ON
APU Generator ON (BOTH)
Engine Start Levers CUT OFF
Doors OPEN AS NEEDED
Air Stairs AS NEEDED
Fasten Belts OFF
Anti-Collision Lights OFF
Fuel Pumps OFF
HYD Pumps OFF
Isolation Valve OPEN
APU Bleed ON
FD’s OFF
Transponder STANDBY
Ground Connections CHOCKS
Parking Brake OFF
*Ground Connections GROUND POWER CART *Option*
*Ground Power ON *Option*
APU Bleed OFF
APU OFF
Secure Cockpit
IRS OFF
EMER Exit Lights OFF
Window Heat OFF
PACK’s OFF
Verify APU OFF
Battery If No Ground power OFF
オフィシャルのマニュアルと並行して読むと より深く理解出来ます。