Books/Book Chapters:
1. Mondal, S., 'Unknown Input State Estimators for Fault Detection and Isolation', LAP Lambert Academic Publishing, October - 2018.
2. Sinha V., Mondal S. (2021) Actuator Fault Detection and Isolation for PEM Fuel Cell Systems Using Unknown Input Observers. In: Bose M., Modi A. (eds) Proceedings of the 7th International Conference on Advances in Energy Research. Springer Proceedings in Energy. Springer, Singapore, October 2020.
3. Sinha V., Mondal S. (2021) Adaptive Unknown Input Observer for Actuator Fault Detection and Isolation of PEM Fuel Cell Systems. In: Rakesh P.K., Sharma A.K., Singh I. (eds) Advances in Engineering Design. Lecture Notes in Mechanical Engineering. Springer, Singapore, February 2021.
4. Sinha V., Mondal S. (2021), Robust Adaptive Observer Based Fault Tolerant Controller Design for Proton Exchange Membrane Fuel Cell Systems, In: MJB Reddy, DK. Mohanta, D Kumar, and D Ghosh (eds) Advances in Smart Grid Automation and Industry 4.0, Lecture Notes in Electrical Engineering, 2021, 693, pp. 263–270 Springer Singapore, May 2021.
5. Manav Kumar and Sharifuddin Mondal, Fuzzy Logic-Based PID Controller Design for Car Suspension System with Magneto-Rheological Damper, In: A. Maurya et al. (eds.), Recent Trends in Mechanical Engineering, Lecture Notes in Mechanical Engineering, https://doi.org/10.1007/978-981-19-7709-1_9, pp. 77-98, June 8, 2023.
6. Manav Kumar, K. Kiran Kumar, and Sharifuddin Mondal, Experimental Investigation of Evaporator Coil Performance with Ethylene Glycol, In: A. Maurya et al. (eds.), Recent Trends in Mechanical Engineering, Lecture Notes in Mechanical Engineering, https://doi.org/10.1007/978-981-19-7709-1_12, pp. 121-129, June 8, 2023
7. Bhaskar Kumar, Prakash Kumar, Sharifuddin Mondal, and Kuntal Maji, Prediction of Surface Roughness in Wire Arc Additive Manufactured Components Using Machine Learning, In: D. Kumar et al. (eds.), Advances in Applied Mechanics, Lecture Notes in Mechanical Engineering, https://doi.org/10.1007/978-981-97-0472-9_50, pp. 373-380, June 22, 2024.
Journal Papers:
Sadhu, S., Mondal, S., Srinivasan, M. and Ghoshal, T. K., ‘Sigma Point Kalman Filter for Bearing only Tracking’, Signal Processing, Vol. 86, No. 12, pp. 3769-3777, 2006.
Mondal, S., Chakraborty, G. and Bhattacharyya, K., ‘An Unknown Input Kalman Filter based Component FDI Algorithm and its Application in Automobiles’, International Journal of Vehicle Autonomous Systems, Vol. 5, No. 3-4, pp. 274-287, 2007.
Mondal, S., Chakraborty, G. and Bhattacharyya, K., ‘Robust unknown input observer for nonlinear systems and its application to fault detection and isolation’, Journal of Dynamic Systems, Measurement, and Control, Transaction of the ASME, Vol. 130, No. 4, pp. 0445031-0445035, 2008.
Mondal, S., Chakraborty, G. and Bhattacharyya, K., ‘Fault detection and isolation of vehicle suspension systems using robust unknown input observers’, International Journal of Vehicle Systems Modelling and Testing, Vol. 3, No. 4, pp. 331-347, 2008.
Mondal, S., Chakraborty, G. and Bhattacharyya, K., ‘Unknown input nonlinear observers for component fault detection and isolation of dynamic systems’, International Journal of Automation and Control, Vol. 3., No. 2/3, pp.154-170, 2009.
Mondal, S., Chakraborty, G. and Bhattacharyya, K., ‘Unknown input high gain observer for fault detection and isolation of uncertain systems’, Engineering Letters, Vol. 17, No. 2, pp. 121-127, 2009.
Mondal, S. and Chung, W. K., ‘Robust Observer based on LMI approach for nonlinear systems with time delays’, International Journal of Systems Control, Vol. 1, No. 1, pp. 22-29, 2010.
Mondal, S., Chakraborty, G. and Bhattacharyya, K., ‘LMI Approach to Robust Unknown Input Observer Design for Continuous Systems with Noise and Uncertainties’, International Journal of Control, Automation and Systems, Vol. 8, No. 2, pp. 210-219, 2010.
Mondal, S. and Chung, W. K., ‘Adaptive observer for a class of nonlinear systems with time delays’, International Journal of Adaptive Control and Signal Processing, Vol. 27, No. 7, pp. 610-619, 2013.
Soni, V., Mondal, S. and Singh, B., ‘Process Parameters Optimization in Turning of Aluminum using a New Hybrid Approach’, International Journal of Innovative Science, Engineering & Technology, Vol. 1, No. 3, pp. 418-423. 2014.
Mondal, S., ‘Design of Unknown Input Observer for Nonlinear Systems with Time-Varying Delays', International Journal of Dynamics and Control, Vol. 3, No. 4, pp. 448-456, 2015.
Mondal, S., ‘Robust adaptive observer for nonlinear time-delay systems with disturbances and uncertainties’, Journal of Control and Decision, Vol. 4, No. 2, pp. 100-113, 2017.
Sinha, V. and Mondal S., 'Recent development on performance modelling and fault diagnosis of fuel cell systems', International Journal of Dynamics and Control, Vol. 6, No. 2, pp. 511-528, 2018.
Kumar, D. and Mondal, S., 'A Fuzzy-TOPSIS Method for Optimizing of Forging Problems', International Journal of Innovative Technology and Exploring Engineering’, Vol.-8, No. 12, pp. 3306-3314, 2019.
Sinha, V. and Mondal, S., 'Sensor FDD based FTC Design for Time-Delay PEMFC Systems', International Journal of Recent Technology and Engineering (IJRTE), Vol. 9, No. 1, pp. 348-353, May 2020.
Tiwary A. K., A. Kumar, S. Mondal, S. Suman, Design and Fabrication of Automobile Roof for Cooling and Heating Purpose, Solid State Technology, Vol. 64, No. 2, pp. 1718-1724, February 2021.
Kumar, D. and Mondal, S., Fuzzy-TOPSIS & Grey-Fuzzy for multi-attribute optimization of process parameters in EDM for Al-2050 alloy, Solid State Technology, Vol. 64, No. 2, pp. 4002-4017, March 2021.
Sinha, V. and Mondal S., 'Adaptive unknown input observer approach for multi-fault diagnosis of PEM fuel cell system with time-delays', Journal of Control and Decision, Vol. 8, No. pp. 222-232, May 2021.
Kumar, D. and Mondal, S., Multi-attribute optimization of EDM process parameters of Al-2050 alloy using Taguchi based TOPSIS and GRA with different rotating tools, International Journal of Modern Manufacturing Technologies (IJMMT), Vol. XIII, NO. 1, pp. 84-95, June 2021.
Kumar, M. and Mondal, S., ‘Recent developments on target tracking problems: A review’, Ocean Engineering, Vol. 236, 109558, pp. 1-20, September 2021.
Aman, N. K. and Mondal, S., 'Thermo-mechanical behavior of the disc brake for varying the number of vanes,' Automotive Science and Engineering (ASE), ISE, Vol. 11, No. 4, pp. 3701-3719, December 2021.
Sinha, V. and Mondal S., 'Robust adaptive fault estimation observer based FTC design for time-delay PEMFC systems,' Journal of The Institution of Engineers (India): Series B, Vol. 103, No. 4, pp. 1305-1314, August 2022.
Tiwary, A. K., Kumar, A., and Mondal, S., Design and Fabrication of an Automobile Heating and Cooling System Based on Thermo-Electric Principle, NeuroQuantology, Vol. 20, No. 10, pp. 4013-4021, August 2022, doi: 10.14704/nq.2022.20.10.NQ55392.
Kumar, M. and Mondal, S., 'Adaptive extended Kalman filter for two-dimensional target tracking using range and bearing angle measurement', Computer Integrated Manufacturing Systems, Vol. 28, No. 12, pp., 2041–2058, December 2022.
Kumar, M., Kumar, K.K., and Mondal S., 'Performance Analysis of Heat Exchanger for Cooling Applications under Dry and Wet Conditions', Heat Transfer Research, Vol. 54, No. 9, pp. 27-48, March 2023. (SCIE, SCOPUS)
Tiwary, A. K., Kumar, A., and Mondal, S., An experimental investigation on exhaust heat recovery system of the gasoline driven vehicle for space conditioning applications, International Journal of Vehicle Performance, Vol. 9, No. 2, pp. 134-149, April 2023, doi: 10.1504/IJVP.2023.10053636. (SCOPUS)
Kumar, M., and Mondal S., 'Adaptive Filters for Two-Dimensional Target Tracking', International Journal of Space Science and Engineering, Vol. 6, No. 4, pp. 350-371, May 2023. (SCOPUS)
Kumar, M., and Mondal S., 'State estimation of radar tracking system using a robust adaptive unscented Kalman filter', Aerospace Systems, Vol. 6, No. 2, pp. 375-381, June 2023. (SCOPUS)
Kumar M, Kumar S, Mondal S., ‘Design and Fatigue Analysis of Connecting Rod with Composite Material Using ANSYS’, NanoWorld Journal, 9(S1): S610-S614, May 2023. (SCOPUS)
Kumar M, Kumar D, Mondal S., ‘Design and Static Analysis of Sandwiched Leaf Spring with Hyper-elastic Material’, NanoWorld Journal, 9(S1): S550-S555, May 2023. (SCOPUS)
Kumar, M., and Mondal S., ‘A fuzzy-based adaptive unscented Kalman filter for state estimation of three-dimensional target tracking’, International Journal of Control, Automation, and Systems, DOI: 10.1007/s12555-022-0441-9, Vol. 21, pp. 3804–3812, November 2023. (SCIE)
Arif, R., Mondal, S. and Mandal, N. P., 'Optimization of Air-conditioning load due to different thermal parameters for a residential building using different techniques', Published online in The Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, DOI: 10.1177/09544062231200960, October 24, 2023. (SCI)
Arif, R., Mondal, S. and Mandal, N. P., 'Optimization of Air-conditioning load for a residential building using Taguchi Method', Published online in The Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, DOI: 10.1177/09544089231215693, November 27, 2023. (SCI)
Jaideva, R. and Mondal, S., A comprehensive experimental investigation on mechanical and thermal performance of Polypropylene - Homopolymer / Unmodified Minor - Mineral Fuller’s Earth composites, Accepted in Iranian Polymer Journal, December 10, 2023. (SCI)
Kumar, R. and Mondal, S., ‘Role of Different Reinforcements in Aluminium 7075-Based Metal Matrix Composite—A Review,’ SAE International Journal of Materials and Manufacturing, Vol. 17, No. 4, pp. 1-10, 2024, DOI:10.4271/05-17-04-0025. (ESCI, SCOPUS)
Kumar, P., Mondal, S. and Maji, K. ‘Analysis and Optimization of Super Duplex Stainless Steel Deposition in Wire Arc Additive Manufacturing Using Machine Learning Techniques,’ SAE International Journal of Materials and Manufacturing, Vol. 18, No. 1, pp. 1-14, 2025, doi:10.4271/05-18-01-0008. (ESCI, SCOPUS)
Kumar, R. and Mondal, S., ‘Recent Developments on Aluminum 7075-Based Composite with Industrial Waste Fly Ash by Stir Casting and Their Applications,' SAE International Journal of Materials and Manufacturing, Vol. 18, No. 2, pp. 1-17, 2025, Doi:10.4271/05-18-02-0009. (ESCI, SCOPUS)
Kumar, M Kumar, K. K., Mondal, S., Khan, M. A., Khan, T. M. Y.,Almakayeel, N, Khan, W. A., ‘Performance evaluation of evaporator coil of a domestic refrigerator under frosting,’ International Journal of Low-Carbon Technologies, 2024, 19, 2746–2754 https://doi.org/10.1093/ijlct/ctae232 (SCIE, SCOPUS).
Kumar, R. and Mondal, S., ‘Effects of inorganic reinforcements on microstructural, mechanical, tribological, and machining characteristics of stir cast Al7075 composite: A review’, Accepted in The Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, February 12, 2025. (SCIE, SCOPUS)
Arif, R., Mondal, S. and Mandal, N. P., 'WASPAS based Taguchi approach to reduce the energy consumption of a typical office building’, Accepted in The Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, February 25, 2025. (SCIE, SCOPUS)
Kumar, M., and Mondal S., ‘Advancements and Prospects of Fuzzy-Based Adaptive Unscented Kalman Filters for Nonlinear Systems: A Review’, Accepted in Applied soft Computing, May 2025 (SCIE, SCOPUS)
Kumar, M., and Mondal S., ‘A Robust Adaptive Approach to Unscented Kalman Filtering for Improved 2D Passive Target Tracking System for Complex Environments’, Accepted in Physical Communication, May 2025 (SCIE, SCOPUS), DOI: 10.1016/j.phycom.2025.102711
Papers published in Scopus listed Proceedings:
Mondal, S., 'Adaptive unknown input observer for nonlinear systems with application to fault diagnosis', IOP Conf. Series: Materials Science and Engineering, Vol. 707, 012001, doi:10.1088/1757-899X/707/1/012001, 2019.
Kumar, D. and Mondal, S., 'Process parameters optimization of AISI M2 steel in EDM using Taguchi based TOPSIS and GRA', Materials Today: Proceedings, Vol. 26, No. 2, pp. 2477-2484, March 2020.
Kumar, D. and Mondal, S., ‘A Review on Modelling, Design and Optimization of Forging Process’, IOP Conference Series: Materials Science and Engineering, Vol. 1026, No 1, pp. 1-12, April 2021.
Kumar, M., Kumar, K.K., and Mondal S., ‘Experimental Investigation of Evaporator Coil Performance with Ethylene Glycol’, International Conference on Progressive Research in Industrial & Mechanical Engineering, NIT Patna, August 5-7, 2021
Conference Papers:
1. Sadhu, S., Mondal, S. and Ghoshal, T.K., ‘Unscented Kalman Filter for Bearing Only Tracking’, In Proceedings of National Workshop for Tactical Missile Guidance, Hyderabad, India, 5th-6th March, 2004.
2. Sadhu, S., Srinivasan, M., Mondal, S. and Ghoshal, T. K., ‘Bearing only Tracking using Square Root Sigma Point Kalman Filter’, In Proceedings of INDICON-2004, IEEE India Annual Conference, Kharagpur, India, 20th-23rd December 2004.
3. Mondal, S., Chakraborty, G. and Bhattacharyya, K., ‘An Improvement on System Fault Detection and Isolation Technique using Unknown Input Observers’, In Proceedings of International Conference on Reliability and Safety Engineering, INCRESE-2005, Bhubaneswar, India, 21st-23rd December, 2005.
4. Mondal, S., Chakraborty, G. and Bhattacharyya, K., ‘A Full Order Luenberger-like Observer for Nonlinear Systems with Unknown Inputs’, In Proceedings of the International Conference on Advances on Control and Optimization of Dynamical Systems, ACODS’2007, Bangalore, India,1st-2ndFebruary, 2007.
5. Mondal, S., Yun, Y., and Chung, W. K., ‘Calibration Technique for Odometry of Mobile Robots using Terminal Iterative Learning Control’, In Proceedings of the 5th International Conference on Ubiquitous Robots and Ambient Intelligence (URAI 2008), Seoul, South Korea, 20-22nd November, 2008.
6. Mondal, S., Chakraborty, G. and Bhattacharyya, K., ‘Unknown input high gain observer for parametric fault detection and isolation of dynamical systems’, In Proceeding of the IAENG International Conference on Control and Automation, Hong Kong, China, 18th-20th March 2009.
7. Mondal, S., Yun, Y., and Chung, W. K., ‘Terminal Iterative Learning Control in Odometry Calibration of Mobile Robots’, In Proceedings of the International Conference on Advanced Intelligent Mechatronics (AIM 2010), pp. 311-316, Montreal, Canada, 6th -9th July, 2010.
8. Kumar, J., Choudaha, S. and Mondal, S., ‘Analyzing the effects of process parameters on welding qualities in Flux Coated Arc Welding (FCAW),’ International Conference on Advances & Development in Engineering & Technology (ICADET), Indore, India, 8th -9th February, 2013.
9. Kumar, D. and Mondal, S., 'Multi-Objective Optimization of ECM process parameters of EN-19 tool steel using Taguchi based TOPSIS,' International Conference on Advances and Soft Computing Applications in Design and Manufacturing, ASCADM 2018, NIT Patna, India, June 4-6, 2018.
10. Kumar, D., Maurya, D. and Mondal, S., 'Fabrication and Testing of Biodegradable Hybrid Composite Material', International Conference on Advances and Soft Computing Applications in Design and Manufacturing, ASCADM 2018, NIT Patna, India, June 4-6, 2018.
11. Tiwary, A.K., Kumar, A. and Mondal, S., 'Power Generation from Exhaust Heat Recovery Using Thermo-Electric Generator', International Conference on Advances and Soft Computing Applications in Design and Manufacturing, ASCADM 2018 , NIT Patna, India, June 4-6, 2018.
12. Sinha, V. and Mondal, S., 'Sensor Fault Detection and Isolation for PEM Fuel Cell Systems Using Unknown Input Observers, In 2nd International Conference on Technological Advances in Mechanical Engineering, Chennai, India, September 19-20, 2018.
13. Mondal, S., 'Adaptive unknown input observer for adaptive state estimation of single link robot arm', International Conference on Recent Advances in Materials and Manufacturing Technologies, Hyderabad, India, November 19-20, 2018.
14. Mondal, S., 'Adaptive Unknown Input Observer for Nonlinear Systems with Application to Fault Diagnosis', International Conference on Mechatronics and Control Engineering, Paris, France, July 23-25, 2019.
15. Sinha, V. and Mondal, S., 'Robust adaptive observer based fault tolerant controller design for proton exchange membrane fuel cell systems', International Conference on Emerging Trends for Smart Grid Automation and Industry 4.0, ICETSGAI4.0 2019, BIT Mesra, India, December 5-7, 2019.
16. Sinha, V. and Mondal, S., 'Actuator Fault Detection and Isolation for PEM Fuel Cell Systems using Unknown Input Observers', 7th International Conference on Advances in Energy Research (ICAER 2019), IIT Bombay, India, 10-12 December 2019.
17. Sinha, V. and Mondal, S., 'Adaptive unknown input observer for actuator fault detection and isolation of PEM fuel cell systems,' International Conference on Innovative Engineering Design (ICoIED 2020), NIT Uttarakhand, 18-20 January 2020.
18. Kumar, D. and Mondal, S., 'Process parameters optimization of AISI M2 steel in EDM using Taguchi based TOPSIS and GRA,' 10th International Conference on Materials Processing and Characterisation (ICMPC 2020), GLA University Mathura, 21–23 February 2020.
19. Sinha, V. and Mondal, S., 'Sensor fault diagnosis based fault tolerant control design for PEMFC systems with disturbances and uncertainties,' International Conference on Advances in Systems, Control and Computing (AISCC2020), MNIT Jaipur, India, January 2020.
20. M. Kumar, A. Prasad and S. Mondal, 'PID controller design for active suspension system with MR damper,' International Conference on Advances in Systems, Control and Computing (AISCC2020), MNIT Jaipur, India, January 2020.
21. S. Mondal, and W. K. Chung ‘ Robust Least Square Filter for Simultaneous Localization and Mapping,’ International Conference on Emerging Frontiers in Electrical and Electronic Technologies (ICEFEET-2020), NIT Patna, India, July 2020.
22. Kumar, D. and Mondal, S., ‘A Review on Modelling, Design and Optimization of Forging Process’, 3rd International Conference on Trends in Material Science and Inventive Materials (ICTMIM 2021), Coimbatore, India, 12-13 March 2021.
23. Kumar, M and Mondal S., ‘Fuzzy Logic Based PID Controller Design for Car Suspension System with Magneto-Rheological Damper’, International Conference on Progressive Research in Industrial & Mechanical Engineering, NIT Patna, August 5-7, 2021.
24. Kumar, M., Kumar, K.K., and Mondal S., ‘Experimental Investigation of Evaporator Coil Performance with Ethylene Glycol’, International Conference on Progressive Research in Industrial & Mechanical Engineering, NIT Patna, August 5-7, 2021.
25. Kumar, M., and Mondal S., 'An Adaptive Cubature Kalman Filtering Process for Two-Dimentional Target Tracking,' International Conference on Emerging Frontiers in Electrical and Electronic Technologies (ICEFEET-2022), NIT Patna, India, June 2022.
26. Kumar. M., Kumar, D. and Mondal, S., 'Design and Static Analysis of Sandwiched Leaf Spring with Hyper-elastic Material', International Conference on Innovations in Mechanical and Materials Engineering (IMME 2022), MNNIT Allahabad, November 4-6, 2022.
27. Kumar. M., Kumar, S.. and Mondal, S., Design and Fatigue Analysis of Connecting Rod Using composite materials, International Conference on Innovations in Mechanical and Materials Engineering (IMME 2022), MNNIT Allahabad, November 4-6, 2022.
28. Kumar, P., Kumar, B., Mondal, S. and Maji, K., Prediction of Surface Roughness in Wire Arc Additive Manufactured Components using Machine Learning, In: 5th Indian Conference on Applied Mechanics (INCAM) 2022, NIT Jamshedpur, November 11-13, 2022.