Geometric Motion lamp
Geometric Motion lamp
we will be sketching and coding and other skills. to make the lamp; this also introduces the project
we will use coding and woodworking to make a lamp
this is the projects constrants
This is our stamp sheet for coding and eletronics/ciructry
this is are stamp sheet for the physical part of the lamp
using code pyhton i made a code and using glow froge i made a design which makes the pattern light up.
we used a laser cutter t cut out are design from inksacpe the we used tape to assemble it while leaving a hole for the lights
we used inkscape to make are desgin with excat me asure that we the uploaded to glow forge
we chose one of our 3d shapes to break it down into 2d shapes so we can use them to make prototype
using the inkscape design we cut out cardboard parts and used tape to put them togther
This is my light plain the first one goes around the outside the lights up the inside.
The 2 pattern goes down the middle first then it cut across
the 3 pattern starts by making a square then going down the middle then goes straight down the middle the makes a diamond wit h the inner lights
using our knowlegde we sketched 4 shapes
we chose one shape to make larger n
we used mu editor to connect the mother board to the coding soft ware
we use mu editor to make the light turn onby connecting 2 wires to gnd and gp11
in mu editor i made the light blink faster by decrasing the number.
we used what we learnd last class to make the red yellow and green lights light up in order
we are going to make bandsaw boxes and learn how to safely use tools
we are working on tools safety
We are expected to know how to use the tools safely
We used a band saw to cut the wood into shapes.
We used it as parctice as a group
I use the band saw to cut out my own part as practice
Band saw
Do
make sure the machine is off before moving items
go slow and steady as not to cut your self
wear goggle/safety glasses when in use
Don'ts
horse play near the machine
keep long hair down
rush
leave the machine unattended
How to use
Make sure the band saws blades are ready then turn on the machine then adjust the blade and slowly push wood through it until cut. After your done make sure the machine is off and the band stopped moving and then move what you cut.
Do
slowly adjust the blade
push threw the machine with care
make sure the machine is off when adjusting
Don'ts
put your hand near the blade at all
dont use wood that has nails or staples
not wear ear and eye protection
how use
adjust the machine to the right hight the, plug in and turn on the machine and push the wood thru. when finshed, turn of the machine.
we used a planer saw to cut down a rough plank of wood until it was smooth.
Do
turn on the saw when lowerd
measure the wood before you cut
stop the saw complety before moving up
Don't
not wear goggles
cut verticaly
mess around near the saw
we cut the wood into 2 using the miter saw ten we glued it together with wood glue
after gluing the wood together we cut off the end of it with the miter saw
Do
wear saftey glasses.
keep sander moving at all times.
don't place the sander on your skin.
Don't
Use without the teacher.
touch sand paper will on.
put the sander on any surface that can damged it.
We used a sand to sand it down the edges
we used a knife to cut out are names then we spray painted over it
a cricket machine was used to cut out the stenicl that we cut the letters out of the stencil which is mad out of vinyl
we cut it with a band saw after we mearused
we used a ruller to mark 3/8ths of an inch
we made a deign in tinker cad then when uploaded it to the printer
we used a band saw out to cut out the marked area
We glued the sides togther then used clamps to hold it there
we used a belt sander to make it smooth and make sure the roof fits
it uses a sd to download a design then un put the sd card into the printer to start printer.
do
make sure the machine is working
make sure you save your design
plug in the plastic wire
Dont
print while somethings on it
unplug while printing
touch it will printing
we used wood a wood stainer and went with the grain
we used a penical and a ruler to make 3d shapes from differnt perspeticvs
we used a bad to cut out the inside of the box
We cut the wood into two peicse using a band
dos
follow the grain of the wood
use a little at a time
go slow
don't
not wear gloves
get on your skin
use a lot
we used stencil and then i used to colors to spary it then i peeled it
we used a 3d printer to make a knob ad the super glued it on to the wood