Wms Oled Button Panel Firmware Download WORK

I had one last week that went out and would not program. Instead of the buttons lit up light green, they were dark with just a single blue LED lit up on the corner of each. It would allow me to read and flash the panel firmware, but would not see the buttons at all. I took it apart, cleaned all the dust off of the board, and re-seated the individual button modules. Some were not pressed down all the way. And the ones that were, I partially unplugged and pressed them down in case of a bad connection. After that, they all lit up green and programmed and worked just fine. Not sure if it was conductive dirt, or just bad connections.

About the only other thing I can guess is that maybe a single button module went bad and is loading down the whole bus. When I had problems with that one, my next step was going to be to replace them one at a time to see if it would work by getting the bad one out of there. But it started working after just reseating them so I never had to do that. You can power up the panel on the bench with a single 24VDC supply and a 2 pin molex connector. Polarity is standard, same as on Aristocrat power supplies, ballasts, and some cooling fans with the Negative side being the side with the latch. On the bench, I power them up taken apart instead of having to put all the screws back in every time to test it. The current firmware is available on the WMS secure site

Wms Oled Button Panel Firmware Download

DOWNLOAD 🔥 https://urluss.com/2y5IpQ 🔥

If you change firmware on a button, the display image test will not work unless you boot it up in a machine first so the machine can load the images on. I couldn't figure out why it was working fine with v3 but scrambling images when I changed the panel to v2. :P

9) Verify all switches work. Verify all displays work (choose display image and select all buttons). There will only be garbled images on the displays until the button panel is installed in a machine but all displays should show something and not be blank or dim. Select Blank Displays and choose all buttons. Blank the displays.

One of the problems that I had was that I made a number of generic switch panels, which had fixed labels. This meant that if I assigned a control in one game, but used the same button for another control in another game, the labeling was wrong for one of them.

As a result I have designed and actually built a panel based on OLEDs that you can use when making custom button / encoder panels for universal use. Essentially, you can make (at the moment) a panel with 7 switches which would connect to either an Arduino or button box of your choice, and then mount a 128 x 64 OLED above the switch. They connect to an Arduino and this displays a unique bitmap icon or text on each OLED, which can be different for each OLED. Using a rotary switch you can then select which game you want (and another OLED shows the game you select), and each individual OLED will then change to reflect the icon or text that represents the switch use in game.

This is just to show the OLED's working. The actual OLEDs themselves can be placed anywhere you want, although I will make a custom panel for my race sim rig. I just did a fast and dirty 3D printed fascia to show the OLEDs in place (size constraints of 3D printer meant 6 max), bear in mind they are only loosely held. Basically, as you either move the rotary switch, or press the appropriate application button, the individual OLED images change depending on the positon of the rotary switch, and you can allocate one OLED to display the app selected (like AMS2 or AMS above)

Each one of those labels is a little bitmap, really easy to make, and you can use any design or text that fits into a 128 x 64 pixel monochrome bitmap

WARNING! There is a risk of hardware damage. During the installation of the update, don't press any buttons, power off the TV, or disconnect it from the AC power outlet. Loss of power during the installation of the firmware update may cause the TV set to become unresponsive or require repair.

WARNING! There is a risk of hardware damage. During the installation of the update, do not press any buttons, power off the TV, or disconnect it from the AC power outlet. Loss of power during the installation of the firmware update may cause the TV set to become unresponsive or require repair.