We compare products from their published specs and features; the verdicts below are our independent editorial opinions.
Updated: 2026-10-06 · 6 min read · Independent comparison
If you want a straightforward wired earbud for calls and music on a phone or tablet, choose Skullcandy Ink'd+; if you need a do-everything wired set for mobile gaming with punchier bass, a longer cable and a magnetic cable that stays out of your way, choose Yatloml Earbuds. Both are 3.5 mm wired earphones built around a noise-isolating in-ear seal rather than active noise cancellation, so "noise isolation" here means they physically block sound by sealing your ear canal — not electronics that cancel it. That distinction matters a lot for mobile gaming, where you want outside chatter muffled but game audio and voice chat delivered without lag.
• Skullcandy Ink'd+ biggest strength: A recognized audio brand with a simple, focused wired design — 3.5 mm plug, in-ear noise-isolating fit, a built-in mic and a one-button remote for calls and track skipping.
• Skullcandy Ink'd+ biggest trade-off: It's a discontinued model, so availability is what it is, and the spec sheet is thin — no cable length, no driver size, no magnet detail.
• Yatloml Earbuds biggest strength: More hardware for the same wired concept — a 10 mm neodymium driver tuned for heavy bass, a 1.2 m cable, magnetic earbuds, and media controls for play/pause and next/previous.
• Yatloml Earbuds biggest trade-off: No mainstream brand backing and a "some devices may require an adapter" caveat, so older or newer phones without a 3.5 mm jack need a dongle.
• Who each pick is for: Skullcandy Ink'd+ for someone who wants a known-name, no-fuss wired earbud for calls and casual listening; Yatloml Earbuds for a gamer or commuter who wants bass, a longer cord and magnetic cable management.
The Ink'd+ is the simpler of the two on paper, and that's not a knock. It's a classic in-ear wired earbud with a 3.5 mm jack, a rounded-tip earpiece, and a noise-isolating fit that relies on sealing your ear canal. Skullcandy lists it with a built-in microphone plus call and track control, so you can answer a call or skip a song from the inline remote instead of digging your phone out of a pocket. The included ear gel sizes are a real practical detail: a proper seal is the whole ballgame with passive isolation, and getting the right tip size is what makes the difference between muffled background noise and none at all.
On audio, the sheet gives a 16-ohm impedance and a 20 Hz–20,000 Hz frequency range with a dynamic driver. Sixteen ohms is low, which generally means these are easy to drive — a phone, tablet or laptop headphone jack will push them without strain. The housing is ABS plastic in Cobalt Blue, and the model is listed as discontinued.
Yatloml Earbuds: Who It's For
The Yatloml set is built around a 10 mm neodymium dynamic driver, and that's the headline number. A larger driver with a neodymium magnet is the usual recipe for stronger low-end, and Yatloml explicitly tunes this pair toward heavy bass with balanced output across genres. For mobile gaming, that low-end emphasis is genuinely useful — explosions, engines and footsteps all live down there, and a bass-forward tuning makes them feel more present than a flat, thin earbud.
The cable is 1.2 meters, which is longer than many bundled wired sets and gives you slack whether the phone is in a pocket, on a desk, or across a tablet stand. The earbuds are magnetic, so they clip together and hang around your neck between rounds — a small thing that turns into a real convenience when you're picking a set up and putting it down constantly. Controls are media-focused: play/pause and next/previous, plus a built-in mic for calls. The housing mixes metal, silicone and TPE, and there's a gold-plated 3.5 mm jack for connectivity.
Two caveats worth knowing. First, it's a teen/adult listing, not a kids' one, and second, the compatibility list explicitly notes that some devices may require an adapter. If your phone dropped the headphone jack, plan for a dongle. In my opinion, this is the better fit for a gamer or commuter who wants bass, a longer cable and magnetic tidiness, and who doesn't mind a lesser-known brand.
Side-by-Side: Which Should You Choose?
• Best for bass-heavy game audio → Yatloml Earbuds. The 10 mm neodymium driver and heavy-bass tuning is the more gaming-friendly sound signature of the two.
• Best for cable management between matches → Yatloml Earbuds. The magnetic earbuds let you hang them around your neck instead of dropping them.
• Best for a household brand name → Skullcandy Ink'd+. Skullcandy is a dedicated audio brand with a Utah design headquarters; Yatloml is a smaller, lesser-known name.
• Best for a simple call-and-music remote → Skullcandy Ink'd+. Call control plus track control is the stated focus, with included ear gel sizes for dialing in the seal.
• Best for kids → Skullcandy Ink'd+. It's listed for a kid age range; the Yatloml is listed for teens and adults.
• Best for easy-to-drive listening → a tie. Both are 16-ohm dynamic drivers with a 20 Hz–20,000 Hz range, so both are easy loads for a phone or laptop jack.
• Best for plug-and-play on any 3.5 mm device → Yatloml Earbuds, with an adapter caveat. It advertises the widest device list, though some devices need an adapter.
I'd buy the Yatloml Earbuds. For mobile gaming specifically, the 10 mm neodymium driver, bass-forward tuning, 1.2 m cable and magnetic earbuds are all decisions I can point to on the spec sheet, and they line up with how I'd actually use a wired set — long sessions, quick put-downs, and wanting the low end to land. I'd pick the Skullcandy Ink'd+ only if a mainstream audio brand, a simple call/track remote and a kid-friendly listing matter more to you than bass and cable length. Check the current price on Amazon for both before deciding, since availability on a discontinued model can shift.
Active noise cancellation uses microphones and electronics to generate sound waves that cancel ambient noise. Neither of these products does that — both rely on passive sound isolation, which means the in-ear tip physically seals your ear canal to block outside noise. That's why tip fit matters so much on both.
How to use noise cancelling earbuds
For these two, "using" noise isolation is about the seal: push the rounded tip gently into your ear canal until outside sound drops noticeably, and try the included ear gel sizes on the Ink'd+ to find your fit. There's no power switch or ANC mode — insertion depth and tip size are your only controls.
How to noise cancelling earbuds
There's nothing to set up. Passive isolation works the moment you insert the earbud correctly, so a snug seal — not a menu setting — is what quiets a train, an office, or a room full of people. If one ear sounds louder or the outside noise leaks in, reseat the tip.
How to noise cancelling earbuds apple
Both sets use a standard 3.5 mm jack. Apple devices without a headphone jack need a Lightning or USB-C adapter, and Yatloml's own compatibility notes flag that some devices may require an adapter. Once connected, the inline mic and controls behave like any wired headset.
As an Amazon Associate I earn from qualifying purchases.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon and affiliated sites.
When you buy through links on this page, we may earn a commission from qualifying purchases at no extra cost to you.
Amazon and the Amazon logo are trademarks of Amazon or its affiliates. This site is an independent third-party review and is not affiliated with, endorsed by, or sponsored by Amazon or the product brands mentioned.
See also: Maxell Teachers 24-Pack vs CYSRALFC Headphones, SOBERNA Tikland vs TRAUSI Headphones: Ipx7 Waterproof, Arafuna CD Player vs RIYADAone Case: Portable Headphones, headphones design