Working at heights is one of the most dangerous hazards on BC worksites. A fall can happen from any height, whether it be the edge of a roof, scaffolding, ladder or loading dock and can result in life-changing injuries. Most of these situations can be avoided with proper planning, equipment and knowing how to use it.
If you’re working at heights you must understand fall protection requirements. This guide will help you understand who needs certifying, what the training entails and what course types are available.
This training will help employees identify and manage fall hazards to avoid injury. This course will teach you how to select the correct anchor points, harnesses and fall arrest system as outlined in Part 11 of WorkSafeBC’s OHS Regulation.
Good fall protection training is practical. You don’t just read about harnesses, you put one on, adjust it and learn to inspect it. You work through real scenarios, including wet weather, pitched roofs, scaffolds, leading edges and tight access points, which are conditions common across the Lower Mainland.
In accordance with the WorkSafeBC regulation, you will be required to receive fall protection training if there is a potential to fall 3 metres (10 feet) or more. If falls can occur and injuries may result, then training will be required. This applies to your employees, sub-contractors and self employed tradesmen.
Roles that commonly need training include:
Roofers, framers and finishing carpenters
Residential and commercial construction workers
HVAC and sheet metal installers
Electricians and solar panel installers
Window cleaners, painters and exterior cladding crews
Telecommunications and tower technicians
Warehouse workers using elevated racking or mezzanines
Arborists and sign installers
Crane riggers
Supervisors and foremen responsible for workers at height
Health and safety committee members
If you’re unsure whether your role requires certification, ask your training provider to help you confirm based on your actual scope of work.
A solid course combines classroom instruction with hands-on equipment practice. Expect to cover the following.
Regulations and hazard identification
WorkSafeBC Part 11 requirements and supporting OHSR sections
Spotting fall hazards on residential, commercial and industrial sites
The hierarchy of controls
Elimination
Guardrails
Travel restraint
Fall restraint
Fall arrest
Control zones
Personal fall arrest system components
Anchors (engineered, permanent and temporary)
Full-body harnesses
Lanyards and self-retracting lifelines
Connectors
Equipment care and calculations
Pre-use inspection and removal-from-service criteria
CSA standards
Swing fall, free fall and clearance calculations using job-site scenarios
How to put on and adjust a full-body harness correctly
Emergency awareness
Suspension trauma awareness
Rescue planning
A combined written and practical evaluation to earn your certificate
Rescue planning deserves special attention. Arresting a fall is only the first step. A worker hanging in a harness needs to be reached quickly, so knowing your plan before you go up matters.
Mainland Safety offers two formats, so you can match the training to the work.
4-Hour Fall Protection Awareness is a condensed half-day session. It suits workers who need a quick refresher or whose exposure to heights is limited. It works well for general labourers, warehouse staff and crews where guardrails or restraint are the primary controls.
8-Hour Fall Protection (Full Day) is the comprehensive option. It is recommended for roofers, framers and anyone who regularly uses a personal fall arrest system. It adds extended hands-on harness fitting, anchor selection, clearance calculations and rescue planning.
A simple rule of thumb: if your day-to-day work depends on a harness and lifeline, take the full day. If you work near edges only occasionally and rely on guardrails, the 4-hour course may be enough. Your employer’s hazard assessment should guide the final decision.
Sending a full crew to an open class can be unproductive. Training on-site means we can come to you in your yard or at your job site throughout the Lower Mainland. Our group rates are available. Give us a call at 604-617-0211 to find out what times and dates would work best for your crew.
We offer public classes in Surrey and Guildford. Training can also be delivered at your workplace in Vancouver, Burnaby and throughout the Lower Mainland. The morning classes usually last around 4.5 hours and the timing will be listed on the course page. If you have a deadline to meet it is best to check availability as early as possible.
Wear suitable clothing and footwear. You’ll be handling gear and practising harness fitting.
Bring real-world questions. Raise the specific anchor points and edges you deal with at work.
Pay attention to inspection steps. Most equipment failures start with gear that should have been pulled from service.
Share what you learn. Brief your crew on rescue planning and inspection habits.
Don’t wait for an incident. Train new hires before their first day at height.
Working at height carries real risk, and training is one of the most effective ways to manage it. To see upcoming dates, compare course lengths and register, visit the fall protection training page or call 604-617-0211. You can also email info@mainlandsafety.ca for group pricing.