HVAC Contractor Woodland Park Portland Oregon

Why to solve typical HVAC breakdowns



There is nothing even worse than waking up cold in the middle of the night.


Its one thing if you just require to pull the cover. Its an entire various concern if your heating system is working improperly or not operating at all.


With a little do-it-yourself experience you can troubleshoot and repair your heating system yourself. Your best option though is to have a maintenance check list for your heating unit to avoid the problem.


Today I have something that will make you feel like you have the knowledge to tackle some heating system repair work.



Whether you have a standard gas furnace or a high efficiency gas heating system comprehending how your furnace/heating system works is essential. You need to comprehend the standard functions of the device so you know what to try to find when there is something incorrect.




Inspect your thermostat to make certain it is switched on.



It might sound silly however check the thermostat to guarantee it is set on "heat" which it is set at least 5 degrees above room temperature level. You might be stunned how numerous service calls are made without checking this!


Here are a few thermostat checks to perform yourself:


Examine the battery on the thermostat. You might require to alter the batteries on your thermostat. If your houses thermostat system works on batteries be sure you are altering them a minimum of as soon as a year or as required.


Some thermostats are wired to your homes electrical system while others utilize batteries. How is yours powered? Often those that utilize batteries will flash a low-battery sign when they require a replacement.


Open the thermostat and gently blow any dust or particles that might have obstructed it.


Ensure the date and time is right on electronic or programmable models - the system may be on a timer.


Inspect the breaker. If on switch off the breaker and check the fuse for the heating system.




Furnace is not producing heat - try to reset the Circuit Breaker


Here are any variety of minor reasons that this might happen. Initially confirm that the thermostat is set to "Heat." Then attempt moving the dial up or down a few degrees to examine if a visible difference is felt.


If there is no outcome check to see if perhaps a circuit breaker or fuse was tripped or blown.



Go to your houses breaker panel and try to find the circuit that controls the heating system. Youre looking to see whether its tossed to the "Off" position or whether its in the middle.


Manually check the breaker. Flip it back and forth.


Ensure it is remaining in the "On" position.


This will reset the breaker. If this does not do the technique you have a problem with either the electrical wiring in the circuit or the circuit breaker itself.



The furnace is not producing sufficient heat. Inspect and change a stopped up filter.


A furnace that has a hard time to produce heat is a different matter from one that has in some way quit working.


When it comes to a poor-performing heating system that does not warm the house sufficiently first ensure that the air filter is tidy and in good condition if not brand-new.


This is a basic but vital part of furnace maintenance. Among the most common reasons to have a heater not working is a clogged filter. It likewise occurs to be the most convenient upkeep chore.


Replacing your heating system filter frequently is a quick and easy task and goes a long method in safeguarding HVAC parts and enhancing your inside air quality.


Find your filter - Some heating systems have their filter in the intake. This more than likely appear like a grate in a floor ceiling or wall. Other filters reside in the heating system itself.



Inspect your filter - You can inform if the time has pertained to alter it by holding it as much as the light. If no light shines through the filter requires changing. A dusty unclean odor from the vents when the blower turns on is another excellent sign you must alter your heater filter.


Change your filter - Make sure your furnace is turned off. No air must be coming out. Check the direction your filter points. Filters are made to trap matter blown from one instructions. Installing your filter upside-down can reduce its effectiveness.


Cleaning the debris that develops on your filters will aid with the circulation of air. When your air filter is obstructed your air handler should work harder to make up for the blockage of air flow. In addition to driving up your energy costs the lowered air circulation through your cooling and heating system can cause your heat exchanger to get too hot and shut down too rapidly.


Filters clean the air headed into the heater and the heated air returned into the house. An unclean clogged filter restricts the airflow ultimately causing heat and pressure to develop up in the heater.


Newer more effective heaters are delicate to the problem and will frequently close down prior to a filthy filter causes more problem. For other units the furnace will continue to run however with less heat output and minimized effectiveness.




Security switch on a heating system door


If your heating system is not running among the first things you should do is examine the security turn on the furnace door. A heater door safety switch avoids the fan and burner from beginning while the access panel is eliminated.


Furnaces have a safety switch that pops out when the door is gotten rid of. The door should be in place for the switch to be triggered and for the heating system to operate.


If you discover you need to set up a new safety switch follow the action by step directions on How to Install a Furnace Door Safety Switch.


Shut the power off. Prep the blower door. Wire the security switch. Examine and evaluate the installation.





Keep the area around your heating system clean and unblocked


This might appear like an apparent idea but sometimes property owners with hectic lives forget to focus on locations of their home like the basement.


A basement can become cluttered which in turn can result in the location around the furnace being filled with miscellaneous possessions and debris. Not just does a clean heater function much better it looks better.


Avoid keeping flammable substances or products near your heater. Crowding your furnace can result in unanticipated fires considerable damage to your house and risk to your household and animals.


Nevertheless convenient it may appear to merely "keep it there" for the summertime consider the opportunity that you may well forget any products youve left on or near your furnace. Dont take possibilities give your furnace the room it requires to operate safely.


Additionally vacuum and tidy frequently around your furnace. While you might have gotten rid of any and all combustible products from the area keep in mind that dust and lint can develop and produce a fire risk. An excess quantity of dust and lint can also trigger your filter to end up being blocked faster than normal needing more frequent replacement.

Woodland Park is an exclusively residential neighborhood in the Northeast section of Portland, Oregon. It borders Madison South on the west, Parkrose Heights on the north and east, and Hazelwood on the south. It is roughly between NE 99th and 102nd, and NE Halsey and NE Tillamook.


Area: 32 acres








Address: 1429 SE 37th Ave, Portland, OR 97214

Address: 3336 SE Belmont St, Portland, OR 97214

Address: 9830 SE Washington St, Portland, OR 97216