We compare products from their published specs and features; the verdicts below are our independent editorial opinions.
Updated: 2026-09-24 · 7 min read · Independent comparison
If you want a complete, ready-to-use pair of wired studio headphones with a closed-back monitoring design, choose Behringer BH 470; if you need to rescue a broken pair of Beats Studio 2 or Studio 3 headphones with a replacement headband, choose Pumyog Studio 3. These two products share a search result and almost nothing else — one is a finished headphone, the other is a spare part. Reading the spec sheets side by side makes that clear fast, and it's the single most important thing to understand before you spend anything.
• Behringer BH 470's biggest strength: a genuine closed-back studio monitoring headphone with 40 mm dynamic drivers, a 20 Hz–20 kHz range and 32-ohm impedance that plays nicely with phones, interfaces and consoles alike.
• Behringer BH 470's biggest trade-off: it's an on-ear, wired-only design, so long sessions may feel tighter than a plush over-ear, and there's no wireless freedom despite the Bluetooth field in its listing.
• Pumyog Studio 3's biggest strength: it's a drop-in replacement arch band for Beats Studio 3 (A1914) and Studio 2 (B0500/B0501), bundled with a magnetic screwdriver, four spare screws and instructions.
• Pumyog Studio 3's biggest trade-off: it is not a headphone. No drivers you can use on their own, no cable, no audio of its own — it only makes sense if you already own the Beats pair it fits.
• Buy the Behringer BH 470 if you want working wired studio headphones out of the box.
• Buy the Pumyog Studio 3 if your Beats headband snapped and the rest of the headphone still works.
The BH 470 is the straightforward choice here: a finished, compact studio monitoring headphone. The core of it is a 40 mm dynamic driver running a 20 Hz to 20 kHz frequency response, which is the full audible range, paired with 32-ohm impedance and 102 dB sensitivity. That combination matters more than it sounds. Low impedance and high sensitivity mean the BH 470 doesn't demand a dedicated headphone amp — it'll run off a phone, a laptop jack, a small interface or a mixing console without you fighting for volume. The ¼-inch adapter for the 1/8-inch connector reinforces that: Behringer clearly built this to move between consumer gear and pro gear.
The closed-back design is the other headline. Closed cups isolate you from the room and keep your monitoring consistent, which is exactly what you want when you're tracking a bass line, checking a mix in a noisy space, or just trying not to annoy everyone around you. The oval ear cups and padded, adjustable headband are built for comfort, and the whole thing folds down compactly — 280 g, with protein leather or memory foam padding and a brown finish. There's a retractable cable and a remote with media control, so it doubles as a daily listening pair, not just a studio tool.
Who should buy it: home recordists, podcasters, students learning to mix, and anyone who wants one wired headphone that works across a phone, an interface and a console. The 20 Hz–20 kHz range and closed-back isolation make it a sensible all-rounder rather than a one-trick monitor.
Who should skip it: if you want active noise cancellation, a truly wireless experience, or an over-ear fit that swallows your whole ear, this isn't it. It's on-ear, it's wired, and the noise control is passive isolation, not electronics. If you already own a healthy pair of premium headphones, the BH 470 is a backup and a budget monitor, not a replacement for something far upmarket.
Now the awkward part: the Pumyog Studio 3 is not a headphone you listen to. It's a replacement headband — an arch band — for Beats by Dr. Dre Studio 3 Wireless (model A1914) and Studio 2 wired or wireless (B0500/B0501). The listing is upfront about that, and so is the spec sheet: no headphone jack, no cable, 0.05 kg, model ST3-HB-BK, matte black.
What it does, it does narrowly and well. Pumyog claims the color, size and construction match the original part closely enough that you can't tell it's been swapped once everything is reassembled. The kit includes the headband, a magnetized screwdriver — genuinely useful given how tiny those screws are — four extra screws and instructions. The brand's own guidance is that a careful person can complete the swap in about ten minutes, and that even someone who's clumsy with disassembly can manage it. Take that as a stated claim rather than a guarantee, but the inclusion of the right driver and spare screws is a real signal that they thought about the job.
The pitch is repair over replacement. Rather than sending a broken pair to a service center or buying new headphones, you replace just the failed arch band and keep the drivers, ear cups and electronics you already own. That's a reasonable argument for anyone attached to their Beats.
Who should buy it: owners of a Beats Studio 3 or Studio 2 whose headband has cracked, snapped or worn out while the rest of the headphone still works — and who are comfortable with a small screwdriver. The three-month replacement-or-refund window on quality issues is worth noting too.
Who should skip it: anyone who doesn't own those specific Beats models, and anyone hoping this is a functioning headphone. It has no jack, no wireless audio of its own and no drivers in the sense you'd use them. If your Beats are dead in the electronics rather than the frame, this part won't save them.
• You want a working headphone today → Behringer BH 470. It arrives as a complete, playable product; the Pumyog part does not.
• You're repairing Beats Studio 3 or Studio 2 → Pumyog Studio 3. It's the only one of the two that fits those models.
• Best for studio monitoring and mixing → Behringer BH 470. Closed-back isolation plus a 20 Hz–20 kHz, 40 mm driver is built for exactly that.
• Best for plug-and-play with phones and consoles → Behringer BH 470. 32-ohm impedance and 102 dB sensitivity, with a ¼-inch adapter for the 1/8-inch jack.
• Best for portability → Behringer BH 470. It folds, weighs 280 g and includes a retractable cable and a brown carry case.
• Best for a small DIY fix → Pumyog Studio 3. Headband, magnetic screwdriver, four spare screws and instructions in one box.
• Best for long over-ear comfort → neither, strictly speaking. The BH 470 is on-ear; the Pumyog part is a frame, not a listening surface.
• Best for noise isolation → Behringer BH 470. Its closed-back cups isolate passively; the Pumyog part offers none of that on its own.
If I had to pick one, I'd buy the Behringer BH 470 — it's a complete, wired, closed-back studio headphone with sensible specs for the money, and it works the moment it's out of the box. The Pumyog Studio 3 is a good product too, but only for a very specific person: the Beats Studio 2 or 3 owner with a broken headband and a working pair of drivers. If that's you, the Pumyog part is the smarter call and a genuinely tidy fix. If it isn't, the BH 470 is the one that actually plays sound. Check the current price on Amazon before deciding — the value math changes with your budget, not with the specs.
what are the best wired studio headphones
That depends on your setup, not a single winner. For a low-impedance, closed-back option that runs off phones and consoles as easily as studio gear, the Behringer BH 470 fits the brief: 40 mm dynamic drivers, 20 Hz–20 kHz and 32-ohm impedance. For anything else, judge by fit, isolation and whether you need a cable or not.
what are wired headphones
Wired headphones connect to your device through a physical cable and jack rather than a wireless link. The Behringer BH 470 uses a 3.5 mm jack with a ¼-inch adapter and a retractable cable, so it plugs straight into a phone, interface or mixing console.
what headphones do professional studios use
Studios typically rely on closed-back monitoring headphones for tracking and isolation, and open-back models for mixing. The BH 470 is a closed-back monitoring design with a 20 Hz–20 kHz range — the kind of spec you'd expect in that role, though every studio's choice comes down to preference and budget.
are all studio headphones wired
No. Plenty of modern studio headphones offer wireless modes, and the Behringer BH 470's own listing even carries a Bluetooth field, though its connectivity is wired with a 3.5 mm jack. If a guaranteed cable connection matters to you, confirm the connectivity before buying.
As an Amazon Associate I earn from qualifying purchases.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon and affiliated sites.
When you buy through links on this page, we may earn a commission from qualifying purchases at no extra cost to you.
Amazon and the Amazon logo are trademarks of Amazon or its affiliates. This site is an independent third-party review and is not affiliated with, endorsed by, or sponsored by Amazon or the product brands mentioned.
See also: LilGadgets Connect+ Pro vs Fidioto 4: Aux Wired Headphones, Acer OHW328 vs IIOZO Apple MFi Certified: Wired Headphones, Bulktech 10 vs Cubilux 3.5mm: Wired Headphones Volume