Abrites Quick Start !!LINK!! Download

How to use the Dongle (Internet connection required)

1. Run "ABRITES Quick Start"

- Click quick link icon on desktop and open ABRITES quick loader.

- Click vehicle icon, an "Dongle" icon appears in the right-bottom corner of desktop (tray bar).

- When the icon appears, the Dongle software is running.

3. Connect the Dongle to computer

4. Run commander

5. If tip "connect TAG programmer" appears

Steps to use SVCI 2020 Quick Start Software:

1. SVCI 2020 Quick Launch Software has 42 shortcut icons. Left-click the icon to launch the corresponding software.

2. Compared to the quick launch of SVCI 2018, the activation dialog is not displayed after clicking the icon.

3. The last icon is the firmware upgrade program. Click it to start the firmware upgrade program.

4. You must be online to download the latest firmware program. After downloading, click Update to update the firmware program.

5. After clicking the icon, the dongle program icon will appear in the tray at the bottom right corner of the computer.

6. The dongle program cannot be exited while the software is running.

Abrites Quick Start Download

DOWNLOAD 🔥 https://shurll.com/2y2Fc9 🔥

7 Step 2. Please, start the executable file SetupInterface_VVxxxx.exe (see above) to initiate the installation procedure and follow the onscreen instructions. Depending on your operational system and settings you may be asked to confirm the start of the installation procedure or to type in your administrative credentials. Press the Next button to proceed with the installation. Read the license agreement carefully and select I accept the agreement if you accept it. Then press the Next button. 7

9 Installing the new generation Abrites Diagnostics for BMW Software During the half of 2014 Abrites ltd. released a new generation of diagnostic software. The Software is currently distributed together with the older platform for the Abrites diagnostics for BMW for user convenience. The new generation software (versions 20.0 and later) requires internet access due to large calculation performed by the Abrites servers instead of the user's computer. In order to install the software the user needs to make sure to connect their AVDI to the computer they are going to use for diagnostic purposes as well as connecting the same computer to the internet. The installation steps are very similar to the ones for the normal Abrites Diagnostic Software, the main differences are described below - If you do not have your AVDI connected to the computer during the installation you will see the following message: - Once the interface is connected the installation will continue: - When the installation is completed the wizard will create a desktop icon. You can distinguish this desktop icon from your Quick start icon. You can tell them apart by the cloud behind the icon. 9

11 Start -> Programs -> ABRITES Common -> AVDI Common User's Manual diagnostics You could use the interface for any given diagnostics by going to the following location: Start -> Programs -> ABRITES software for IDxxxxxx -> diagnosticss (where IDxxxxxx is your ADVI ID) ABPROG By going to the following location: Start -> Programs -> ABRITES software for IDxxxxxx -> ABPROG Programmer for AVDI (where IDxxxxxx is your ADVI ID) You could access the ABPROG Programmer for AVDI. ZN030-ABPROG and ZN031-M35XXX/SPI/I2C Adapter together with Abrites EEPROM Programmer software allows you to erase and write SPI EEPROM memory with and without incremental registers. *A detailed user manual is included in the installation directory of the function described above. 2. Quick Start The Abrites Quick Start for IDXXXXXX where XXXXXX is the ID of your AVDI is a simplified user interface which allows you to start working with the AVDI in a much quicker manner. After the installation is complete you should have a Quick start icon on your desktop as well as a start menu shortcut. Interface preparation and connection to the PC Connect the USB cable from the AVDI package to the interface. 11

14 If you HAVE connected a TAG programmer you should see this message: If you have connected a TAG programmer you should see a message that the Tag Programmer is successfully recognized and you can start working. 3. USING AVDI WITH A VIRTUAL MACHINE (VM) If you like to use your AVDI interface (software ) with a virtual machine here are some preliminaries that should be made. Install AVDI software on the VM After you have loaded and played the VM on which you would like to use your AVDI interface, please install the ABRITES Software for the AVDI interface which you want to use on the VM. This is done exactly as the installation on your host PC (see 3.1 Software installation steps). Be sure that the checkbox about the installation of the interface s USB drivers is set, especially if you are installing the Abrites Diagnostic Software for the first time on this machine. You should see the following window: Wait for the drivers to be installed. 14

16 If you like to disconnect the AVDI interface from the VM (so you can use it on the host PC) you can either close the VM Player or do it through the VMWare menu Virtual Machine Removable devices future devices avdi interface Vvxxx Disconnect (Connect to host). Set latency timer Another prerequisite before you start using the AVDI interface on the VM is to set the latency timer of the COM port where the AVDI interface is recognized to 1ms. This can be done in the following way: Open Windows Explorer then right click on My computer and select Properties. 16

34 Interface not connected If you see this message you need to check whether the interface is connected to the computer, if it is connected properly and you see this message again contact us at the following address : support@abrites.com Internet synchronization (hardware update). The latest AVDI Diagnostics update introduced a mandatory update of the hardware over internet. This update is regular and should be performed at least once a month. If the internet update is not performed, the hardware will have limited functionality and will be not able to connect to vehicles until it is activated. Please note that performing the internet update is an essential initial step. For most of the functionality of your AVDI you will not require to have an internet connection to your computer. It is required only for the Internet update. You do not need to have your computer constantly online, only during the update(s). The procedure for performing the AVDI internet update is as follows: 1. Download and install the latest AVDI Diagnostics update and please start the Abrites diagnostics 2. This internet update is performed automatically once the AVDI Diagnostics software is started. It is indicated by the message "Performing internet activation...". 3. If the internet activation is successful, the next time you start the diagnostic software, the message "Performing internet activation..." should be not shown. IMPORTANT: If the message "Performing internet activation..." is not displayed the time you start the application, your hardware is ready for use. The internet update will expire in one month when you will need to reconnect your computer to the internet and make sure your interface performs the update when you start your Abrites diagnostic software. 4. If the message "Performing internet activation..." continues to be shown the internet update was not successful and the possible reasons for this issue might be: 34

35 - No internet connection to the computer you are installing your software on. In that case please allow the connection of this computer to the internet. - The date on your computer is incorrect.in that case please set the time and date on your computer to the current time and date at your location. NOTE: Due to the time zone after running the latest SW update for the first time, the internet update might not be successful in the first 1-2hours. Effects if the internet update is not performed: - The AVDI hardware is recognized OK, but no connection to the vehicle is possible. - Some diagnostic software might crash if you try to connect to the car. -The update MUST be performed periodically (every 30days) in order for your AVDI to always work properly and not experience any of the symptoms above. Make sure to connect your AVDI and allow it to perform its internet update every 30 days. In case the procedure does not go as planned and you encounter an issue different to the ones above please contact support@abrites.com with a detailed description of the steps you took and their effect. - Upon starting the Abrites diagnostics software in the top right hand side of the screen you will see how many days (or hours) you have until the next synchronization. In case you see the following message you will need to perform the online update of your hardware. - Then perform the following steps (After making sure that you have a stable internet connection): 1. Start your Abrites diagnostic software 2. When you start the software you will see the following message: 35

55 6. License Viewer License viewer is a tool installed on every computer where the Abrites diagnostic software is installed. It is used to display what special functions you currently have for your AVDI and what you do not. The functions are lined up in accordance to the license names in alphabetical order and the currently available licenses for your interface are marked with a green tick. On the other hand the licenses that are not available are displayed with a red X. License viewer is located in C:\ (Program Files) Program Files (x86)\abrites software for ID XXXXXX where XXXXXX is the ID number of your AVDI. Using the license viewer you can check your licenses yourself at any time. 55 ff782bc1db