List of Items:

Open SPR is a surface plasmon resonance based sensing device with the sensitivity down to ng/ml.

This Fiber optic Spectrometer is of Ocean Optics make. The model number is USB4000 XR1 ES. The specification of the Grating is as follows: It is 31, 500 lines/mm, blazed at 250 nm; The Spectral Range is from 200-1025 nm(UV – Vis-NIR); The dimension of the entrance slit is 25 µm; The Full Width Half Maximum is 1.7-2.0 nm;(Refer Ocean optics site for detailed specifications) 

This is a Sandvic make Honeycomb Breadboard of dimensions 120 cm X 90 cm; It consists of a rigid table support for conducting optical experiments. The surface is of stainless steel with a rectangular grid of tapped holes, where the optical components are placed properly, to avoid movements.

The Light source is from Ocean Optics. The model number is HL – 2000. It is optimized for the VIS-NIR (360 nm-2000 nm) with adjustable focusing of the SMA 905 connector to maximize light coupling into a fiber. A fan keeps the source cool and stable. A built-in filter slot accepts optical filters up to 25.4-mm round or up to 50.8-mm square and up to 3 mm thick. 

Fiber optic coupler: Microscope objective (Alco make) with magnification 45X, numerical aperture 0.67, tube length 160 mm and the cover glass thickness is 0.17 cm. Fiber holders held by XY positioner against the objective. The other optomechanical components include : XYZ Translation stage for precise positioning in all three dimensions, The XY Fiber positioned would help positioning in two dimensions, the kinematic Fiber positioner is also for alignment of the optical fiber. The Optical Fiber cutting Block helps in slicing the fiber into pieces of necessary length.  

Upright microsope from Radical, RXLr-4IT with 4X, 10X, 40X, 100X Objectives. It has transmission and reflectance mode. It has a CMOS detector with 3.15 mp resolution, 35 fps frame rate and 10 bit A/D convertor.

Three Lasers are available of 532, 650 and 785 nm wavelength. 785 nm Laser has power control. A line Laser of 532 nm wavelength is also available.

This is a hand held instrument. The Sample size of two to three drops is sufficient for measurement. High temperature samples can be measured. Response time 3 seconds Calibration with pure water Measurement range of Brix 0.0 to 53.0 %, Temperature 9.0 to 99.9°C, with resolution Brix 0.1 %, Temperature 0.1°C and accuracy Brix ±0.2 %, Temperature ±1°C and measurement time of 3 s. 

The spectrum response complies with standards of International Commission on Illumination. The measuring range is 10 Lux to 100-500 Lux with a resolution upto 0.1 Lux. It has automatic compensation for cosine angle of incident light. The sampling rate is 2.5 times/second. The photosensitive component is Si-light cell attached with light filter. 

Image sensor 2 MP with video or still capture and automatic white balance and exposure. Resolution can extend up to 1600X1200, 24 bit RCB of frame rate 30 f/s under 600 Lux brightness. Magnification is 20 X to 800 X ; It has 8 LEDs. Micro capture 2.0 software to capture images. 

A multichannel high sensitivity spectrometer from Horiba Scientific Triax 190 is an optical device used to simultaneously analyze multiple wavelengths or spectral bands. It employs sophisticated techniques to split light into distinct channels, allowing for the simultaneous measurement of different wavelengths, enabling comprehensive and precise data collection across a broad range of wavelengths for detailed analysis and measurement. 

Flat bed power meter from Thorlabs S130VC power range covering from 0.5 mW to 50 mW and wavelength ranging from 200 nm to 1100 nm feature enhanced shielding to avoid electromagnetic interference as well as an over-temperature alert sensor to warn against damage and measurement errors due to overheating of the sensor. 

Fiber cleaver prepares optical fibers for fusion splicing or connector termination by using a precise cutting mechanism for achieving a clean and flat cleave. It ensures a clean and flat end face which is crucial for optimal light transmission.  

Thorlabs PM100USB power meter provides selectable bandwidth of either 20 Hz or 100 kHz offers more flexibility and adaptability to specific measurement tasks. It provides communication between an attached sensor and a PC or other external control unit. They are designed to be controlled via an external device or operated autonomously using the analog output; there are no controls or display screens.  

HR 2000 spectrometer is a unique combination of technologies providing users with both an unusually high spectral response and high optical resolution in a small footprint and designed for considerable flexibility in connecting to various modules as well as external interfaces. The detector used here is a high sensitivity 2048 element CCD array.   

Evanescent wave absorbance based eight-channel array fiber optic absorbance biosensor (ArFAB) using U-bent fiber optic sensor probes for multi-analyte detection or multi-sample analysis in real-time. 

Deuterium halogen lamp provides stable and continuous light output over a broad spectrum ranging from 200 nm to 700 nm. The deuterium component provides UV light for applications that require high-energy photons, while the halogen component extends the wavelength coverage into the visible and near-infrared regions. 

LEDs inhouse built are use for matching the specific requirements like wavelength, intensity and duration of light exposure. It can be integrated with other laboratory equipment and software for seamless experimentation. 

Fluorescent microscope from cilika BT-P provides white LED illumination with continuous intensity control allows you to achieve the desired contrast and brightness for your sample. It comes with the whole range of magnifications. Equipped with a quadruple /quintuple nosepiece and 4X, 10X,40X. The variable viewing angle of the display allows to set the screen to the comfort.  

Temperature range: ambience to 250 oC Digital PID temperature control and digital timer. Dimensions: 450 X 450 X 450 mm3. The inner chamber is made of 304 Stainless steel, the outer chamber is made of powder coated mild steel. The temperature uniformity is maintained by Forced Air circulation fan. Manufacturer: Vani Scientific.

The hot plate was manufactured by Vani Scientific and Equipments. The power rating of the hot plate is 500 Watt, 220 V supply . The Hot plate is fixed with temperature control. 

Hot air blower Quick850AD with temperature control from 100-480 Celsius, with temperature display and Air control display.

pH meter with manual and auto mode, AP1-Plus model with standby, temp, mV and pH modes. 

The instrument was manufactured by Life Care Equipment Pvt Ltd. It has One Chamber made of 304 Stainless steel with 5 Liter tank capacity, 120 W Power output with Piezo -ceramic type transducer, MOSFET based SMPS generator with pulse sweep power. It has a timer, heater of 500 W and internal temperature controller.

One number each of 0.1-2.5μl, 0.5-10μl, 2-20μl , 20-200μl and 100-1000μl. These are piston stroke pipettes that operate according to air cushion principle. It has a control button, volume setting ring, ejector and Volume display. The tip cone is spring loaded. There is an ejector sleeve foe ejecting pipette tips after use.

Analytical balance (Precisa XB 220A) with automatic calibration option and could be calibrated in appropriate time intervals. The Standard weights necessary for calibration are also available. The instrument has a weighing range up to 220 g with readability of 0.1 mg. Data interface is possible. 

Remi CM101 Vortex mixer. Variable speed mixer to eliminate hand mixing. Speed regulator controls the degree of vibration. Suitable for touch/continuous operations. 

Reagent bottles, Conical flasks, volumetric flasks and measuring jars of various sizes for wet lab experiments pertaining to this lab are available. 

Autoclave from Equitron is a sturdy and tension free equipment can safely be operated repeatedly even in remote places. Ideal for Microbiology, Tissue Culture, etc. Inside and outside chamber and reservoir are fully stainless steel. Flange, fly screw, cross pin are also fully stainless steel. All internal joints are argon welded. Finely polished, crevice-free internals.  

Colony counter from Equitron has circular tube and powerful magnifying lens which reduces operator fatigue. It is a desktop compact model with complete SS construction. On marking the colony by applying a slight pressure with the marker pen, a count is registered and confirmed by an audio beep. 

Chemical Lab Fume Hood is a type of ventilation system that primarily functions to provide personal protection against toxic fumes, vapors and dust. Its secondary function includes protection against chemical spills, runaway reactions and fires by acting as a physical barrier. 

Laminar flow bench is made up of duro board and covered with white Decolam or Formica. The interior surface of the instrument is painted with epoxy. This offers a clean air with an efficiency of 99.97% by Pre and HEPA filters. Work table is made from SS top with plexi glass. 

Magnetic stirrer from IKA RCT Basic is suitable for stirring tasks and reaches a hotplate temperature up to 310 degree celsius and speed up to 1500 rpm. With the connection option for an external temperature sensor, the temperature can be measured and controlled directly in the reaction medium.     

Centrifuge from Remi CM-12 Plus is one of the newly developed compact benchtop cooling models offers quiet operation with very small footprint. It is useful for routine applications in bio-technology, PCR, life sciences, bio-chemical and clinical labs etc. This unit is ideal for centrifugation with micro tubes from 0.2 ml up to 1.5 ml. 

Centrifuge from Neuation ifuge M15k delivers top notch accuracy in every cycle despite high load. It gives smooth and silent operation even at the maximum speed. The lightning fast 15000 rpm microprocessor controlled centrifuge can perform at peak efficiency and give the desired results. 

Using fiber micro stripper, the outer cable jacket and fiber buffer can be stripped, a connector ferrule crimped over the fiber and onto the outer cable jacket; and the fiber is cleaved at its very bare end. The termination takes less than 2 minutes per end using an easy crimp and cleave process, which produces a high-quality end-face. The process is completely mechanical, minimizing the impact of user error. Proper termination is easily verified by visible light. 

Shaker incubator from eps orbital shaker 053 is a thermos scientific shaker and has outstanding performance, as well accuracy for mixing of samples. Simplicity of its mechanism in controlling temperature and time adjustment prevents the risk of error when establishing run conditions.  

Low RPM mixer helps to maintain the integrity of sensitive samples and offer precise control over the mixing process. Gentle mixing at low speeds reduces heat generation. They are specifically designed for rotating tubes or vials. They come in various configurations, including horizontal and vertical rotation, and can operate at low speeds up to 100 rpm for sample mixing. 

Holds 1 Syringe from micro-liter sizes up to 60 mL.(140 mL partially filled). Infusion rates from 0.73 µL/hr (1 mL syringe) to 1500 mL/hr (60 mL syringe). Easy-to-use keypad interface: Set the syringe diameter, pumping rate, press Start and Stop. Syringe purge mode and Power failure mode settings available. Displays total volume dispensed in mL or µL units Infusion rate can be changed while pumping with Selectable infusion rates units: mL/hr, µL/hr, mL/min, µL/min. 

USB lock-in 250 from Alfatec. 

The 9129B is an economical triple output linear programmable DC power supply featuring isolated outputs that can be adjusted independently or combined in series or parallel to output higher voltage or current. Additionally, this supply can operate in tracking mode with user-configurable ratios between channels. 

The Digital Storage Oscilloscope provides you with affordable performance in a compact design. Packed with standard features - including USB connectivity, 16 automated measurements, limit testing, data logging, and context-sensitive help - the oscilloscopes help you get more done, in less time. 

Production Workhorse Low Cost Soldering Station. Has temperature locking, long life ceramic heating element, In-built digital calibration, 7 segment LED display, suitable for lead-free soldering.

Carbon dioxide laser from synrad Series 48-1SAN with 10 W power and is air cooling. 

 8 channel and 16 channel data acquisition systems from National Instruments.

Scientific SM 5076A 10MHZ function generator. 

The Keysight U1252B 4.5-digit handheld digital multimeter (DMM) is feature-packed to simplify the troubleshooting of electronics and electrical circuits on the bench or in the field. Key capabilities include manual and automated data logging to both DMM and PC. For those long, continuous measurements, the DMM equips you with the easy-to-use GUI data-logging software to automate virtually unlimited data recordings to PC. The U1252B comes with an integrated 20 MHz frequency counter for high frequency measurements, and a built-in programmable square-wave generator with selectable frequency and duty cycle. With the versatile U1252B, you are well equipped to perform thorough troubleshooting of any faulty circuit. 

Thin, light, compact body design for one-hand operation , 18mm triangular jaw allows for easy measurement on small cables , 200 A ac and dc current and 600 V ac and dc voltage measurement range , 3000 Ω resistance range, continuity detection , Zero function allows the display to be cleared for DC measurements , CAT III 600 V safety rating , Data Hold function.

A DC power supply is a reliable device that delivers consistent direct current to power electronic devices and circuits. Its adjustable settings for voltage and current make it essential for experiments, circuit testing.

Aoyue i474A+ desoldering station has a long life Ceramic heating element Atmega8A Microprocessor from Microchip and a proprietary software proportional control of the temperature with high power of 70 W. 12 Volt high Flow Vacuum Pump that produces up to 15 L/min.  

LCD-based SLA 3D Printer. Create intricate designs with layer resolutions ranging from 25 to 100um, ensuring both fine details and efficient printing. With a printing speed of 20mm/h, this printer offers swift production without compromising quality. It has a printing volume of 115mm *65mm *155mm and printing material is 405nm photosensitive resin.

YOOCNC - Desktop CNC engraving machine with 4030Z CNC 4 axis controller and a 800W high speed spindle

A laser engraving machine is a powerful tool that utilizes laser technology to cut, etch designs, patterns, or text onto various materials with precision and accuracy. Employing focused laser beams, these machines are mostly used to cut acrylic sheets. 

A semi-automated machine using focused lasers and motors to process of shaping and manipulating fiber optics. Its primary function involves precisely bending optical fibers without compromising their structural integrity or optical performance 

Using a stepper motor it controls the vertical movement/positioning of a platform for precise adjustments in height or depth