Permastone
CARE AND MAINTENANCE
Although NAFCO floors are durable, all floor coverings require some
care to look their best. Many problems can be prevented before they
occur. Special attention should be paid when selecting a floor for your
specific needs.
The type and frequency of traffic on your NAFCO floor will determine
the frequency of maintenance needed. The type of floor and even the
color will also have some bearing on how much care may be
necessary. For example, solid color floors will visually show scuffs,
scratches, dirt and general wear to a greater degree than multi-colors
of chips or patterns. Of course, white or light colors will visually show
staining to a greater degree than darker colors. For this reason, solid
color and white floors should receive special attention in regard to
preventive maintenance and the amount of care provided. Good
judgement when choosing the type and style of your new floor will help
prevent maintenance problems before the floor is even installed.
If Tarkett 400 or Tarkett 850 adhesives were used when installing your
floor, all traffic and furniture should stay off the floor for at least 24
hours to allow the adhesive to dry completely.
Quik-Stik tiles or Tarkett 800 adhesive installations may be walked
upon immediately after completion
NOTE: DO NOT WASH ANY INSTALLATION FOR 48 HOURS!
· In order to prevent indentations and scratches, use glass,
polished metal or other non-staining cups or casters with flat
under surfaces (see diagrams on pages 4 & 5).
· Protect your floor against burns. NAFCO floors can be damaged
by burns from the glowing end of a cigarette, matches, or other
extremely hot items.
· Protect your floor from tracked-in dirt and grit particles by using
mats at all outside entrances. Take the time to remove any
imbedded grit particles from shoe soles before entering the room.
Avoid the use of rubber or latex-backed mats, as certain rubber
compounds can permanently stain vinyl (consult the mat
manufacturer to determine if their backing will stain vinyl).
Avoid tracking in tar or asphalt from driveways, as this can also
discolor vinyl.
· Avoid stilleto or damaged high heels on your floor. They can
cause permanent damage.
· All NAFCO floors have good resistance to stains. They are not
affected by most common household spills; however, any spill
should be cleaned up immediately. The longer the spilled material
is left on the floor, the greater the risk of permanently staining the
floor. For information regarding the proper method or solution to
use on a specific stain, see the chart on page 4.
· Avoid exposure to direct sunlight for prolonged periods, as this can
result in tile discoloration. Excessive temperatures might cause tile
expansion. During peak sunlight hours, the use of drapes or
blinds is recommended especially on patio doors, etc., that
receive direct sunlight.
RESIDENTIAL AND LIGHT COMMERCIAL
MAINTENANCE
Light daily sweeping or vacuuming will prevent dirt and grit particles from
being ground into the surface of the floor. If the floor is swept daily, a light
weekly washing should be sufficient. The type and frequency of traffic
will determine the frequency of maintenance needed. After the first
week or so, it will be necessary to use Tarkett SureShine® cleaner or an
equal neutral floor cleaner. Apply the SureShine® cleaner to the floor with
a sponge mop. After the soil deposits have been loosened from the floor,
mop thoroughly with clean water to remove them and all detergents, then
rinse the floor with clean, warm water to remove all soapy residue. Do
not flood the floor with water. Any detergent film left on the floor can
hold tracked-in dirt and leave the surface with a dull, cloudy
appearance.
NAFCO's factory Tritonite™ finish is resistant to scuffing, wear from
normal use, and common stains. However, the finish is not
indestructible and will scratch when subjected to harsh conditions.
NAFCO luxury vinyl tiles have a surface factory finish top coat. The
finish is applied during the manufacturing process and is either high
gloss or matte satin, depending upon the product style. All gloss levels
are maintained in the same way.
In time, high traffic areas may begin to show a reduction in gloss. When
this occurs, thoroughly clean and dry the floor. Apply a light coat of
Tarkett SureShine® Polish. To apply Tarkett SureShine® Polish, pour the
liquid in a shallow pan; dip in a sponge mop and wring it out gently,
leaving it saturated with the liquid polish. Mop in one direction to insure
uniform distribution. Do not mop too vigorously as this could cause
bubbles.
Continue to apply Tarkett SureShine® Polish to the floor until the entire
floor is evenly coated. SureShine® Polish dries in 30 minutes; if more than
one coat is desired, be sure to let each coat completely dry before
applying another. Keep in mind that 2-3 thin coats are better than one
heavy coat.
In time, it will be necessary to strip the old layers of Tarkett SureShine®
Polish and apply fresh coats. Strip the polish by using a high-quality
wax/polish remover.