C.-S. Shin, T.-C. Lin, & S.-H. Huang. An Energy Modulation Interrogation Technique for Monitoring the Adhesive Joint Integrity Using the Full Spectral Response of Fiber Bragg Grating Sensors. Sensors 2025, 25(1), 36.  https://doi.org/10.3390/s25010036

C.-S. Shin & S.-H. Huang, Evaluation of Fatigue Damage Monitoring of Single-Lap Composite Adhesive Joint Using Conductivity. Polymers 2024, 16(16), 2374. https://doi.org/10.3390/polym16162374

C.-S. Shin & L.-W. Chen, Damage Monitoring of Composite Adhesive Joint Integrity Using Conductivity and Fiber Bragg Grating. Polymers 2023, 15, 1575. https://doi.org/10.3390/polym15061575

C.-L. Lin, S.-G Wang, M.-T. Tien, C.-H. Chiang, Y.-C. Lee, P.L. Baldeck, C.-S. Shin, A Novel Methodology for Detecting Variations in Cell Surface Antigens Using Cell-Tearing by Optical Tweezers. Biosensors 2022, 12(8), 656. https://doi.org/10.3390/bios12080656

CS Shin & TC Lin, 2022, “Hygrothermal damage monitoring of composite adhesive joint using the full spectral response of fiber Bragg grating sensors”, Polymers 2022, 14, 368. https://doi.org/10.3390/polym14030368

CS Shin & TC Lin, 2021, “Adhesive Joint Integrity Monitoring Using the Full Spectral Response of Fiber Bragg Grating Sensors”,  Polymers ( Section Polymer Composites and Nanocomposites) 2021, 13(17), 2954; https://doi.org/10.3390/polym13172954

CS Shin, PL Baldeck, YM Nie, YH Lee, ZD Lin, CC Chiang, CL Lin, 2021, “Design and evaluation of a 3D multi-manifold micromixer realized by a double-Archimedes-screw for rapid mixing within a short distance”, Journal of the Taiwan Institute of Chemical Engineers 120, 59-66. https://doi.org/10.1016/j.jtice.2021.03.028

CS Shin, YC Chang, 2021, “Fabrication and Compressive Behavior of a Micro-Lattice Composite by High Resolution DLP Stereolithography”,  Polymers (Section Polymer Composites and Nanocomposites), 13(5), 785; https://doi.org/10.3390/polym13050785

CL LIN, SG WANG, MT TIEN, CHAN CHIANG, YIC LEE, PL BALDECK, CS Shin, 2022, ”A quantitative methodology to detect surface antigens on red blood cells using optical cell-detachment technique”, Research Square, DOI:10.21203/rs.3.rs-134189/v1.

SK Liaw*, DC Li, HC Lee, YZ Huang, CS Shin and YW Lee, 2019, “Multiple Parameters Optical Sensing Using Fiber Ring Laser Based on Fiber Bragg Gratings and 1064 nm Semiconductor Optical Amplifier”, Optics and Spectroscopy, Vol. 127, No. 6, pp. 1057–1061.

BL Chen, CS Shin, 2019, “An Improved Impact Source Locating System Using FBG Rosette Array”, Sensors 19 (16), 3453; doi:10.1117/12.923237.

Chow-Shing Shin, Tzu-Jui Li and Chih-Lang Lin, 2018, “Alleviating Distortion and Improving the Young’s Modulus in Two-Photon Polymerization Fabrications”, Micromachines, 9, 615; doi:10.3390/mi9120615  (SCI, 1st author)

Chih-Wen Chi, Chun-Chieh Lee, Chun-Pin Lin, Chow-Shing Shin, 2017, "Cyclic fatigue behavior of NiTi dental rotary files in clinical simulated root canals",Journal of the Formosan Medical Association, Vol.116, 306-312 http://dx.doi.org/10.1016/j.jfma.2016.06.002 (SCI, corresponding author)

Chih-Wen Chi, Eddie Hsiang-Hua Lai, Chao-Yuan Liu, Chun-Pin Lin ,Chow-Shing Shin, 2017, "The influence of heat treatment on cyclic fatigue and cutting efficiency of ProTaper Universal F2 instruments", Journal of Dental Sciences, Vol.12, pp. 21-26. http://dx.doi.org/10.1016/j.jds.2016.06.001 (SCI, corresponding author)

Chow-Shing Shin and Hau-Ming Jiang, 2016, “Tentative probes into some aspects of the pipeline rupture behind the 2014 Kaohsiung underground gas explosions”,Journal of the Chinese Institute of Engineers, Vol 39, No 4, pp. 404-412. (SCI)

Yu-Lin Shen and Chow-Shing Shin, 2016, “Pressurized line pipe wall thinning detection using a distributed fiber-optic sensing system”, Journal of the Chinese Institute of Engineers, Vol 39, No 4, pp. 413-417. (SCI, corresponding author)

單秋成, 沈育霖, 趙子豪, 2015, “歐盟EN81-1與我國升降機規範之比較及妥適性探討”, 勞動及職業安全衛生研究季刊,第23卷第3期, 104年9月, pp.349-362.

YJ Liu, JY Yang, YM Nie, CH Lu, ED Huang, CS Shin, P Baldeck, CL Lin, 2014, “A simple and direct reading flow meter fabricated by two-photon polymerization for microfluidic channel”, Microfluidics and Nanofluidics, 1-5 (SCI)

SK Liaw, CS Shin, WF Wu, 2014, “Tunable fiber laser using fiber Bragg gratings integrated carbon fiber composite with large tuning range”, Optics & Laser Technology 64, pp.302-307. (SCI)

SK Liaw, WF Wu, CS Shin, 2014, “Tunable L-band fiber lasers using fiber bragg gratings and wavelength reflector”, Microwave and Optical Technology Letters 56 (11), pp.2681-2683. (SCI)

CS Shin, SK Liaw, SW Yang, 2014, “Post-Impact Fatigue Damage Monitoring Using Fiber Bragg Grating Sensors”, Sensors 14 (3), 4144-4153. (SCI)

C. S. Shin, Y. H. Huang, C. W. Chi & C. P. Lin, 2014, “Fatigue life enhancement of NiTi rotary endodontic instruments by progressive reciprocating operation”, International Endodontic Journal, 47 (9), pp. 882–888. (SCI)

HY Hsu, YL Yu, SK Liaw, RY Liu, CS Shin, 2014,“Theoretical and experimental study of multifunction C+ L band hybrid fiber amplifiers”, Optics & Laser Technology, Vol. 56, pp. 307–312. (SCI)

Shin, C. S.; Tseng, Y. T.; Liaw, S. K., 2013, “A Novel Fiber Bragg Grating Needle Pressure Sensor for Medical Applications”, Journal of Neuroscience and Neuroengineering, Vol. 2, No. 1, Feb. 2013, pp. 53-57.

Y. L. Yu, S. K. Liaw, R. Y. Liu, C. S. Shin, 2013 “WDM PON purpose remote pumped bidirectional EDFA using cascading FBGS as a pump reflector”, Microwave and Optical Technology Letters, Vol 55, Issue 11, pp. 2553–2556. (SCI)

C.S. Shin, C. Y. Liu and S.C.Hsu, 2013, “In-situ Fatigue Crack Initiation Monitoring in NiTi Rotary Endodontic Instruments”, Advanced Materials Research Vol.647, pp.3-8. (EI)

C. S. Shin, Q. M. Chang and C. P. Lin, 2013,“A critical analysis on the cyclic fatigue testing of rotary endodontic instrument”, Applied Mechanics and Materials, Vol. 431, pp.82-87. (EI)

C. S. Shin and S.W. Lin, 2012 “Evaluating Fatigue Crack Propagation Properties Using Miniature Specimens” International Journal of Fatigue, Volume 43, October, pp. 105–110. (SCI)

S. K. Liaw, H. Wang, K. H. Hsu, S. C. Lin, N. -K. Chen, C. S. Shin and Y. Tver’yanovich, 2012, “Linear-cavity fiber laser in nearly single-frequency operation using Faraday rotator mirror”, Laser Physics, Volume 22, Number 2, 437-440 (SCI)

Liaw, S.K., Wang, S., Shin, C.S., Yu, Y.L., Chen, N.K., Hsu, K.C., Manshina, A., Tver'Yanovich, Y., 2010, “Linear-cavity fiber laser using subring-cavity incorporated saturable absorber for single-frequency operation”, Laser Physics, Volume 20, Issue 8, August 2010, pp. 1744-1746. (SCI)

Liaw, S.K., Wang, S., Shin, C.S., Chen, N.K., Hsu, K.C., Manshina, A., Tver'Yanovich, Y., Su, C.-F., Wang, L.K., 2010, “Single-longitudinal-mode linear-cavity fiber laser using multiple subring-cavities”, Laser Physics, Volume 20, Issue 7, July 2010, pp. 1608-1611. (SCI)

C. Y. Huang, C. S. Shin, Y. C. Chen, 2010, “The Rapid Brazing of Stainless Steel Wire and Low Carbon Steel Wire by Using of Ultra-high Frequency Induction Heating“, J. the Taiwan Society for Metal Heat Treatment, Vol.107, Dec. pp.23-30.

B. L. Chen, C. S. Shin, 2010, “Fiber Bragg Gratings Array for Structural Health Monitoring”, Special issue on Sensors, Actuators and Intelligent Processing, Materials and Manufacturing Process, Vol.25, No.4, pp.255-258, DOI:10.1080/10426910903426414. (SCI)

C. S. Shin, B. L. Chen, J. R. Cheng and S. K. Liaw, 2010, “Impact response of a wind turbine blade measured by distributed FBG sensors”, Special issue on Sensors, Actuators and Intelligent Processing, Materials and Manufacturing Process, Vol.25, No.4, pp.268-271, DOI:10.1080/10426910903426448. (SCI)

C.S. Shin and J.C. Huang, 2010, “Effect of temper, specimen orientation and test temperature on the tensile and fatigue properties of SiC reinforced PM 6061 Al alloy”, International Journal of Fatigue, Volume 32, Issue 10, October 2010, pp.1573-1581, doi:10.1016/j.ijfatigue.2010.02.015. (SCI)

C.-H. Chen, Y. L. Shen and C. S. Shin, 2010, “Using a distributed brillouin fiber sensor to detect strain and cracks in steel structures”, Journal of Mechanics, Vol.26, pp.547-551 (SCI)

C. S. Shin, B. L. Chen and S. K. Liaw, 2010, “An FBG based impact event logging and locating system for structural health monitoring”, Invited submission to Special Issue on “Structural Health Monitoring for Civil Structures: From the Lab to the Field”, Journal of Advances in Civil Engineering, Vol 2010, doi:10.1155/2010/253274.

C. S. Shin and M. W. Lin, 2010, “An optical fiber based curvature sensor for endodontic files inside a tooth root canal”, IEEE Sensors Journal, Vol.10, Issue 6, 2010, Article number 5443728, pp.1061-1065 (SCI)

Yu-Lin Shen, Chow-Shing Shin, 2009, “Distributed Sensing Floor for an Intelligent Environment”, IEEE Sensor Journal, Vol.9, No.12, December, pp.1673-1678. (SCI)

C.S. Shin, C.Q. Cai, 2008, “Surface fatigue crack growth suppression in cylindrical rods by artificial infiltration”, International Journal of Fatigue, Volume 30, Issue 3, Pages 560-567 (SCI)

R. V. Prakash, P. Bhokardole and C.S. Shin, 2008  “Investigation of Material Fatigue Behavior Through Cyclic Ball Indentation Testing”, Journal of ASTM International, Vol. 5, No. 9, Paper ID JAI101042. (EI)

單秋成，何彥儒，楊仕偉，鄭錦榮，2008, “複合材料衝擊、扭轉及膠合破壞檢測技術之比較”，臺電工程月刊 719:83-97。

單秋成，黃寬明，郭鴻達，2008,“核能電廠閥桿受力量規之研發”，臺電工程月刊 721:53-59。

R.V. Prakash and C. S. Shin, 2007, “An evaluation of stress-strain property prediction by automated ball indentation (ABI) testing” JOURNAL OF TESTING AND EVALUATION 35 (3): 221-232 MAY 2007. NSC92-2811-E-002-041, NSC94-2212-E-002-031 (SCI)

C. S. Shin and C. Q. Cai, 2007 “Evaluating Fatigue Crack Propagation Properties Using A Cylindrical Rod specimen” International Journal of Fatigue, Vol. 29, Issue 3, pp. 397–405. NSC93-2212-E-002-062  (SCI)

M.C. Young, L.W. Tsay, C. S. Shin, S.L.I. Chan, 2007 “The effect of short time post-weld heat treatment on the fatigue crack growth of 2205 duplex stainless steel welds,” International Journal of Fatigue, Volume 29, Issue 12, pp. 2155-2162. (SCI)

S.K. Liaw, K.L. Hung, Y.T. Lin, C.C. Chiang, C.S. Shin, 2007, “C-band continuously tunable lasers using tunable fiber Bragg gratings”, OPTICS AND LASER TECHNOLOGY 39 (6): 1214-1217. (SCI)

C.C. Chiang, C. L. Lin and C.S. Shin, 2006, “Application of the embedded optical fiber Bragg grating sensors in detecting the internal fatigue damage of Gr/Epoxy laminated composites,” Journal of the Chinese Society of Mechanical Engineers, Vol.27, No.6, pp.801-807. (SCI)

C.S. Shin and C.C. Chiang, 2006, ”Embedded Fibre Bragg Grating Sensors for Internal Fatigue Damage Monitoring in Polymeric Composites”, Vol.321-323, pp.230-233, Key Engineering Materials. NSC91-2212-E-002 -056 and NSC92-2212-E-002-002.

U.M. Li, C. S. Shin, W.H. Lan and C.P. Lin, 2006 “Application of NonDestructive Testing in Cyclic Fatigue of Endodontic Ni-Ti Rotary Instruments”, , Vol.25, No.2: pp.247-252,, Dental Materials Journal. (SCI)

C. S. Shin and C. Q. Cai, 2006 “Fatigue crack propagation properties from small sized rod specimens”  236, pp,2574– 2579, Nuclear Engineering and Design. NSC93-2212-E-002-062 (SCI)

C.S. Shin and C.C. Chiang, 2006 ”Fatigue Damage Monitoring in Polymeric Composites using multiple Fibre Bragg Gratings,” International Journal of Fatigue, Vol.28, No.10, pp.1315-1321. NSC92-2212-E- 002 -002 (SCI)

C.S. Shin and C.C. Chiang, 2006 “Temperature compensated fiber Bragg grating using fiber reinforced polymetric composites", Vol.29, No.3, pp.519-526, Journal of the Chinese Institute of Engineers. NSC90-2212-E002-175 and NSC91-2212-E-002-056 (SCI)

C.S. Shin, C.C. Chiang and S. K. Liaw, 2006 “Comparison of Single and Double Cladding Long Period Fiber Grating Sensor using an Intensity Modulation Interrogation System” Optics Communications, Vol. 258, pp.23-29. NSC 92-2212-E-002-002 (SCI)

C.S. Shin and C.C. Chiang, 2005 “Deformation Monitoring by Using Optical Fiber Grating Sensor”, Journal of the Chinese Institute of Engineers,Vol.28,No.6,pp.985-992. NSC91-2212-E-002-056 and NSC 92-2212-E-002-002 (SCI)

C. Q. Cai and C. S. Shin, 2005, “A normalized area-compliance method for monitoring surface crack development in a cylindrical rod,” International Journal of Fatigue, Vol.27, Issue 7, pp. 801-809. (SCI)  NSC93-2212E-002-062

M.C.Young, S.L.I.Chan, L.W.Tsay and C. S. Shin, 2005 “Hydrogen-enhanced Cracking of 2205 Duplex Stainless Steel Welds” Mat. Chem. Phy., Vol. 91, No.10, pp. 21-27 (SCI) NSC 92-2216-E-019-009.

C. M. Wang and C. S. Shin, 2004, “Fictitious Crack Growth Model and Residual Strength Prediction Of Composite Laminates with Sharp Notches,” under revision, Journal of Composites Materials. (SCI) NSC89-2218-E-002-035

C. S. Shin and C. Q. Cai, 2004, “Experimental and Finite Element analyses on stress intensity factors of elliptical surface crack in a circular shaft under tension and bending,” International Journal of Fracture, Vol.129, pp.239-264. (SCI) NSC92-2212-E-002-008

C. S. Shin and P. C. Chen, 2004, “Fatigue crack propagation testing using subsized rotating bending specimens”, Nuclear Engineering and Design,  Vol.231, No.1, pp. 13-26.  (SCI)  NSC91-2212-E-002-030

J.C. Huang, C. S. Shin and S.L.I. Chan, 2004, “Effect of temper, specimen orientation and test temperature on tensile and fatigue properties of wrought and PM AA6061- alloys,” International Journal of Fatigue, Vol.26, pp.691-703. (SCI) NSC90-2212-E-002-031

C. Q. Cai, and C. S. Shin, 2004, “A discussion on “The Stress Intensity Factor Study of an Elliptical Cracked Shaft” by Y. S. Shih and J. J. Chen, ” Nuclear Engineering and Design, Vol.227, No.3 pp. 355-358. (SCI) NSC92-2212-E-002-008

C. S. Shin and, C. M. Wang, 2004 “An Improved Cohesive Zone Model for Residual Notched Strength Prediction of Composite Laminates with Different Orthotropic Lay-ups,” Journal of Composites Materials, Vol. 38, No. 9, pp.713-736. (SCI) NSC89-2218-E-002-035

C. S. Shin and, C. M. Wang, 2002 “A comparison of as-fatigue and Re-consolidation Residual Properties of Notched Quasi-isotropic [0/45/90/-45]2s and Cross-ply [0/90]4s AS4/PEEK Composite Laminates,” Composites Part A, Vol.33, pp.1519-1528. (SCI) NSC88-2212-E-002-041

C. M. Wang and C. S. Shin, 2002 “As-fatigue and Re-consolidation Residual Properties of Notched [0/90]4s AS4/PEEK Composite Laminates,”Composites Part B:engineering, Vol.33, pp.67-76.(SCI) NSC 88-2212- E- 002 -041

單秋成、王楚明、林志郎，2002，“複合材料內部損傷之偵測“，強化塑膠，第九十一期，pp.60-72。NSC90-2212-E-002-175

馬劍清，單秋成，張志毅，蔡賜慶，楊仁和，陳慶東，陳景林，鍾年勉，2002，"臺中電廠主汽機抽汽逆止閥之損壞原因研究"，臺電工程月刊，643 ，民91.03，pp.1-32。

徐貴炎，吳文方，單秋成，黃振國，2002，"核二廠反應器爐心頂部導架之結構完整性分析與可靠度評估"，臺電工程月刊，631，民90.03，pp.51-62。

C. S. Shin and Z. Z. Chen, 2001, “Fatigue life extension by electroless nickel infiltration plating”, International Journal of Fatigue, Vol.23, pp.777-788. (SCI) NSC 89-2212-E-002-006

單秋成、林志郎，2001，“光纖光柵在複合材料內部缺陷與內部應力、溫度監測之應用“，檢測科技，19:5，民90.09-10，pp.164-178。NSC90-2212-E-002-175

單秋成，2001，"裂紋填充在疲勞裂紋止裂之探討"，工程科技通訊，56 民90.06，pp.108-111。NSC 89-2212-E-002-006

C. S. Shin and C. Q. Cai, 2000, “A model for evaluating the effect of fatigue crack repair by the infiltration method,”, Fatigue & Fracture of Engineering Materials & Structures, Vol.23, .835-845. (SCI) NSC 89-2212-E-002-006

C. S. Shin and R. Z. Li, 1999, “Fatigue Crack Propagation in the Elastic-plastic Regime in a Low Alloy Structural Steel,” Invited contribution to the Fracture Mechanics and Fatigue Special Issue of the Journal of the Chinese Institute of Engineers, Vol.22, No.3, pp.275-284.(EI, SCI) NSC 88-2212-E-002-057

C. S. Shin and Z. Z. Chen, 1999, “A Novel Method For Repairing Fatigue Crack,” Invited contribution to the special issue on “Recent Developments in Fatigue and Fracture Mechanics-based Analysis and Design of Structures”, Journal of Structural Engineering,Vol.26, No.1, April, pp.55-62. NSC 88-2212-E-002-057

H. Y. Liou, W. F. Wu and C. S. Shin, 1999, “A modified model for the estimation of fatigue life derived from random vibration theory”, Probabilistic Engineering Mechanics, Vol.14, pp.281-288 (SCI)

周漢興，單秋成，宋佩瑄，許伯秋，張力，1999，"在3.5%鹽水中形成裂縫間氧化物對疲勞裂縫生長之影響，中正嶺學報，28:1 民88.09 頁23-37。

單秋成，王俊博，1999，"疲勞裂縫自動量測系統之發展"，檢測科技 ，17:1，民88.01-02，pp.4-20。

C. S. Shin, K. C. Huang and R. Z. Li, 1998, “Artificial retardation of fatigue crack growth by the infiltration of cracks by foreign materials,” Fatigue & Fracture of Engineering Materials & Structures, Vol.21, pp.835-846. (SCI )

C. S. Shin and J. B. Wang, 1998, “Mechanical properties of a low temperature cured ceramic matrix composite,”  Materials Chemistry and Physics, Vol.55, pp.94-101. (SCI)

P. S. Song, S. Hwang and C. S. Shin, 1998, “Effect of artificial closure materials on crack growth retardation, ” Engineering Fracture Mechanics, Vol.60, No.1, pp.47-58. (SCI)

D. Kujawski and C. S. Shin, 1997, “On the elastic longitudinal stress estimation in the neighbourhood of notches, ” Engineering Fracture Mechanics, Vol.56, No.1, pp.137-138. (SCI)

L. Tau, S. L. I. Chan and C. S. Shin, 1996, “Hydrogen enhanced fatigue crack propagation of bainitic and tempered martensitic steels, ” Corrosion Science, Vol.38, No.11, pp.2049-2060. (SCI)

C. S. Shin, C. M. Wang and P. S. Song, 1996, 'Fatigue damage repair -- A comparison of some possible methods, ” International Journal of Fatigue, Vol.18, No.8, p.535-546. (SCI)

P. S. Song, S. Hwang and C. S. Shin, 1996, “Enhancement in fatigue life through electroplated nickel-induced crack closure, ” the Journal of the Chinese Society of Mechanical Engineers, Vol.17, No.6, pp.601-607.

C. S. Shin, 1996, “Continuous Service Reassurance of Steam Turbine Blades, ” Engineering Failure Analysis, Vol.3, No.2, pp.95-102. (SCI)

L. Tau, S.L.I. Chan and C. S. Shin, 1996, “Effect of anisotropy on the hydrogen content, diffusivity and fatigue crack propagation of a banded ferrite/pearlite steel, ” in Hydrogen Effect in Materials, (Referred) Eds. A. W. Thompson and N. R. Moody. TMS, pp.475-485.

Wen-Fang Wu, C. S. Shin and Jyh-Jeng Shen, 1994, “Probabilistic analysis of fatigue crack propagation under random loading, ” Trans. ASME, J. Pressure Vessel Technology, vol.116, May, pp.216-225. (SCI)

C. S. Shin, R. P. Tseng and W.T. Jao, 1994, “Experimental and analytical fracture assessment of 165mm diameter AISI 304 seamless piping containing circumferential through-walled crack, ” The International Journal of Pressure Vessels and Piping Vol.57 pp.169-185. (SCI)

Wen-Fang Wu, C. S. Shin and C.H. Tsai, 1994, “A reliability assessment of reactor pressure vessels, ” The International Journal of Pressure Vessels and Piping, Vol.57, pp.77-84. (SCI)

C. S. Shin, K. C. Man and C.M. Wang, 1994, “A Practical method to estimate the stress concentration factors of notches, ” The International Journal of Fatigue, Vol.16, June,pp.242-256. (SCI)

C. S. Shin and C.M. Wang, 1994, “Experimental calibration of stress intensity factor for piping with cirucumferential through-wall crack,” The International Journal of Pressure Vessel and piping, Vol.60, pp.285-296. (SCI)

L. Tau, S.L.I. Chan and C. S. Shin, 1994, “Effect of anisotropy on the hydrogen induced fatigue crack propagation of a banded ferrite/pearlite steel,” Journal of Marine Science and Technology, Vol.1, No.4, pp.19-22.

B. C. Sheu, P. S. Song and C. S. Shin, 1994, “The effect of infiltration induced crack closure on crack growth retardation, ” Scripta Metallurgica et Materialia, Vol.31,No.10,pp.1301-1306. (SCI)

吳文方, 單秋成, 陳宗權, 陳弘毅, 1993, “隨機負荷下之疲勞裂縫延伸與疲勞可靠度分析, ”中國航空太空學會學刊,Vol.26,No.2,pp.173-181.

C. S. Shin, W. H. Huang and H. Y. Chen, 1993, “'An Improved DC potential drop System for crack length measurement, ” Journal of the Chinese Institute of Engineers, Vol.16, No.1, pp.29-40.(EI)

C. S. Shin and S.H. Hsu, 1992, “On the mechanism and behaviour of overload retardation in AISI 304 stainless steel, ”  International Journal of Fatigue Vol.15 No.3 pp.181-192. (SCI)

C. S. Shin, P. L. Wu and W.T. Jao, 1992, “Engineering assessment method in the prediction of elastic-plastic fracture behabviour, ” The Journal of the Chinese Society of Mechanical Engineers,vol.13, No.6, pp.505-518.

C. S. Shin, W.T. Jao and P.L. Wu, 1992, “A re-appraisal of the Net Section Plastic Collapse Method in the assessment of elastic-plastic fracture, ” The Journal of the Chinese Society of Mechanical Engineers, Vol.13,No.3,pp.198-204.

C. S. Shin and S. H. Hsu, 1992, “Fatigue life extension by an artificially induced retardation mechanism, ” Engineering Fracture Mechanics, Vol.43, No.4, pp.677-684. (SCI)

C. S. Shin, 1991, “Some aspects of corner fatigue crack growth, ” International Journal of Fatigue, Vol.13, No.3, pp.233-240. (SCI)

單秋成,徐森煌,1991, “拉伸超載後勞裂縫封閉行為量測方法之探討, ” 中華民國力學學會期刊第八卷,第四期第365-376頁

C. S. Shin, 1990, “The stress intensity factors of corner cracks emanating from holes,” Engineering Fracture Mechanics, Vol.37, No.2, pp.423-436. (SCI)

C. S. Shin and N. A. Fleck, 1989, “The fatigue and fracture of a zinc die casting alloy', ” International journal of Fatigue, Vol.11, No.5, pp.341-346. (SCI)

C. S. Shin., and  R. A. Smith, 1988, “Fatigue crack growth behaviour of a zinc-aluminium alloy at high homologous temperatures, ” Fatigue and Fracture of Engineering Materials and Structures, Vol.11, No.2, pp.109-122. (SCI)

C.S.Shin and R.A.Smith, 1988, “Fatigue crack growth at stress concentrations -- the role of notch plasticity and crack closure, ” Engineering Fracture Mechanics, Vol.29, No.3, pp.301-315. (SCI)

C. S. Shin and N. A. Fleck, 1987, “Overload retardation in a structural steel, ” Fatigue and Fracture of Engineering Materials and Structures, Vol.9, No.5, pp.379-393. (SCI)

L. S. Chen & C. S. Shin, 1988, “A comparison of various stress intensity factor extraction methods from finite element stress analysis,” MRL Bulletin of Research & Development, Materials Research Laboratories, Vol.2 , No.2, pp.53-58. (EI)

C. S. Shin, 1987, “Some observations about the size effect in the fatigue of notched specimens, ” Scripta Metallurgica, Vol.21, pp.1335-1339. (SCI)

C. S. Shin, 1986, “A discussion on various estimations of elastic stress distributions and stress concentration factors for sharp edge notches, ” International Journal of Fatigue, Vol.8, No.4, pp.235-237. (SCI)

C. S. Shin and R. A. Smith, 1985, “Fatigue crack growth from sharp notches, ” International Journal of Fatigue, Vol.7, No.2, pp.87-93. (SCI)

N. A. Fleck, C. S. Shin and R. A. Smith, 1985, “Fatigue crack growth under compressive loading,” Engineering Fracture Mechanics, Vol.21, No.1, pp.173-185. (SCI)