Interfacing Servo Motor with P89V51RD2

Introduction

In this guide, we will learn how to interface a servo motor with the 8051 microcontroller. A servo motor is a widely used device that allows precise control of angular position. We will use the 8051's pins to generate PWM (Pulse Width Modulation) signals required to control the servo motor's position.

More details about working of Servo:   Download  

Problem statement

The objective of this project is to interface a servo motor with 8051 and write a program to continuously rotate servo motor from 0 to 180 degrees and back to 0 degrees. 

Requirements

1.  P89V51RD2 

2.  Servo motor

3.  Jumper wires

Working

The control circuit interprets input signals, usually in the form of pulse width modulation (PWM), which specifies the desired position or angle for the motor shaft. The position feedback mechanism, such as a potentiometer or an encoder, provides information about the motor's current position.

The control circuit compares the desired position with the actual position indicated by the feedback mechanism. If there is a deviation, the control circuit adjusts the motor's output to correct the difference and bring the motor to the desired position. This closed-loop control system ensures accurate and consistent positioning.

The DC motor, coupled with a gear mechanism, converts the electrical signals into rotational motion. The gear mechanism reduces speed and increases torque output, allowing for precise and controlled movement of the motor shaft. 

PWM frequency is set to 50Hz, which is a common frequency used for servo motors. However, different servo motors may have different frequency requirements.

Circuit Diagram

Code

• Copy and paste the following code into main.c or download it from here: 

#include <reg51.h>

#define PWM_Period 0xB7FE   //Define value to be loaded in timer for PWM period of 20 milli second

sbit Servo_Motor_Pin = P2^0;

unsigned int ON_Period, OFF_Period, DutyCycle;

void delay(unsigned int count) //delay function for 1ms

{

    int i,j;

    for(i=0; i<count; i++)

      for(j=0; j<112; j++);

}

void Timer_init()            

{

  TMOD = 0x01;                   //timer0 mode1

  TH0 = (PWM_Period >> 8);       //20ms timer value

  TL0 = PWM_Period;              

  TR0 = 1;                       //start timer0

}

void Timer0_ISR() interrupt 1   //timer 0 interrupy service routine(ISR)

{

  Servo_Motor_Pin = !Servo_Motor_Pin;

  if(Servo_Motor_Pin)

  {

    TH0 = (ON_Period >> 8);

    TL0 = ON_Period;

  }

  else

  {

    TH0 = (OFF_Period >> 8);

    TL0 = OFF_Period;

  }  

}

void Set_DutyCycle_To(float duty_cycle)  //calculate on and off period from duty cycle

{

  float period = 65535 - PWM_Period;

  ON_Period = ((period/100.0) * duty_cycle);

  OFF_Period = (period - ON_Period);  

  ON_Period = 65535 - ON_Period;  

  OFF_Period = 65535 - OFF_Period;

}

int main()

{

   EA  = 1;                 //enable global interrupt

   ET0 = 1;                 //enable timer0 interrupt

   Timer_init();

   while(1)

    {

  Set_DutyCycle_To(2.7);    //0.54ms(2.7%) of 20ms(100%) period

  delay(1000);

  Set_DutyCycle_To(7);     //1.4ms(7%) of 20ms(100%) period

  delay(1000);

  Set_DutyCycle_To(12);    //2.4ms(12%) of 20ms(100%) period

  delay(1000);

    }

}

Output

The servo motor performs a continuous rotation from 0 to 180 degrees and back to 0 degrees. 

Conclusion

By interfacing a servo motor with the 8051 microcontroller, precise control of rotational movement can be achieved in various applications, including robotics, automation, and positioning systems. The microcontroller's ability to generate PWM signals and the servo motor's responsiveness and accuracy enable the implementation of systems that require controlled and repeatable motion.