First you will need to buy the parts necessary to build the computer.

1. Processor (CPU)

2. Computer Case

3. Optical Drive (DVD RW and SATA capable)

4. Memory (RAM)

5. Power Supply

6. SATA Cables

7. Motherboard (SATA Capable)

8. Processor Fan

9. Case Fan

10. Hard Drive (SATA Capable)

11. Assortment of case and drive screws (Not Pictured)

12. Flowers (necessary if you are invading the space of your significant other)

Caution: Double check the manufacturer’s specifications on all items before you purchase them. Kits are supposed to contain compatible parts, but mistakes can happen.

Gather the tools you will need for the project:

• Screwdriver (for slotted and Phillips head screws)

• Wire cutters and strippers

• Needle-nosed pliers

• Utility knife

• Small flashlight

• Adjustable wrench

• Small container to hold screws

• Heat sink compound

• Grounding Strap

You may not use every single one of these tools in every installation, but it is best to have all of them on hand in case you have a use for them.

Warning: Using incorrect tools for a task (such as turning a screw with a knife blade) can cause equipment damage and bodily injury.

Open the computer case by removing the side panels. Find the screws that hold the side panels in place and remove them. The panel is removed by first sliding it back then lifting it away from the case.

Warning: Case may have sharp edges. Handle with care to avoid injury.

Three things need to be done before assembly begins:

• Remove any parts or packaging materials that may have been shipped inside the case.

• Remove the cover for the optical drive. On our case, we will be removing the cover on the highest drive bay to mount our DVD drive. Do this by pressing in the retaining tabs.

• Make note of the cables pre-installed in the case. These should be front panel connections for features such as the power switch, audio jacks and USB ports. If they are not labeled, consult the manufacturer’s documentation and label them yourself now before other parts are installed in the case.

Put the grounding strap on your wrist and connect the other end to the computer case. If your strap is not equipped with a clip to hook to the case, find a place to wedge against the metal. This will prevent any buildup of static electricity on your body from damaging the computer components.

Caution:Static electricity can ruin computer components. Always wear a grounding strap when handling any internal components.

Follow these steps to install the motherboard in the case:

• Install the I/O bezel plate into the opening in the back of the case. It pushes in from the inside.

• Install standoffs in the case. The standoffs screw into the motherboard mounting holes. Check the screw hole locations on the motherboard for exact placement.

• Lower the motherboard into the case and align with the I/O bezel.

• Install the screws.

Caution: To prevent damage to the motherboard it must only contact the standoffs and screws. All of the standoffs and screws must be installed.

The hard drive is the device that stores all of your data. It is 3.5" wide and needs to be mounted so that you can gain access to the cable connections on the back. If that is not possible you may need to connect cables before you install the drive. To mount the drive:

• Find a 3.5" drive bay to install the drive in. If you have trouble finding a place to mount the drive consult your case documentation for suggestions.

• Slide the drive into place until the screw holes on the sides are lined up with the holes in the case.

• Install the screws.

The optical drive is 5.25" wide and is installed in the drive bay that we removed the cover from in a previous step. Cable access considerations apply to this drive also. To install the drive:

• Slide the drive into the drive bay until the screw holes are lined up and the front of the drive is flush with the front of the case . Make sure that it is orientated correctly.

• Install the screws.

The CPU is the brain of the computer. It is installed on the motherboard in the socket. To install the CPU:

• Find the corner marking that designates pin 1 of the CPU. On this AMD brand processor, the corner is marked with an arrow. Consult the manufacturer's documentation for specific information about your processor.

• Lift the small metal rod next to the socket.

• Find the corresponding marking on the CPU socket and insert the CPU so that the markings are lined up.

• Push the rod down to lock the processor in place.

The RAM is the temporary memory location that the processor works from. Permanently stored data is pulled from disks and stored in RAM while the processor works with it. The memory is easy to install:

• Set the RAM board in the socket. Check to see that the notch in the board is in the correct location. If it is not, turn it around 180º.

• Press firmly on both ends of the board to set it into the socket. Make sure the tabs lock into place.

Caution: Pressing the boards in when the tab is not aligned could cause damage to the RAM boards as well as the motherboard.

The CPU fan is really a combination of a heat sink and fan together. The unit draws heat away from the CPU . To install the fan:

• Place thermal compound to the CPU following the instructions provided with the compound.

• Set the fan assembly on the CPU with mounting tabs aligned.

• Pull the locking rod down on the fan assembly to lock into place.

• Connect the fan assembly's power connector to the motherboard. Consult the manual to determine proper placement.

Caution: Failure to apply thermal compound will result in insufficient cooling and will cause damage to the CPU and/or motherboard.

The case fan is usually installed on the back panel of the case. If the fan mount is not obvious consult the case documentation. To mount the fan:

• Align the mounting holes by holding the fan to the mounting pad on the inside of the case. The fan needs to be mounted so that it blows air out of the case.

• Insert the screws from the outside of the case and tighten.

Consult your case documentation for details and then follow these directions to install the power supply:

• Align the mounting holes in the case and power supply.

• Insert screws and tighten.

With all of the components installed in the case, the jungle of wires can be daunting. It is important to consult the motherboard manual in order to make sure proper connections are made. There are two kinds of connections, power and data.

• Every device that has been installed needs power. The motherboard has two power connections, and there are two connectors specifically for SATA devices (drives). The other connectors will run fans and other non-SATA devices.

• Data cables connect drives and front panel devices to the motherboard. Please consult the motherboard documentation for the exact placement of connectors.

Warning: Incorrect connections can damage components and cause bodily injury.

Now that the components are completely installed, the last thing to do is to reinstall the side panels on the case. The computer is now ready to be turned on and to have software loaded on it. If the computer has problems starting up, check all component connections and mounting to make sure that you have hooked everything up correctly. Consult individual component manuals for specific troubleshooting information if problems persist.