How We Research
We compare products from their published specs and features; the verdicts below are our independent editorial opinions.
If you want a proper eight-channel stereo line mixer that lets you monitor multiple sources through headphones at once, choose QudosXy HA800S; if you need to blend up to four condenser microphones into one clean output for calls, streaming or recording, choose Jectse 4. That one sentence is the whole decision. Everything below is me working through the specs so you can sanity-check it for your own setup — whether that's a home studio desk or a remote work corner where a bluetooth headset for remote work is only half the story.
• QudosXy HA800S — biggest strength: eight independent stereo channels, each with its own volume knob and a STEREO/MONO switch, all routed through standard 1/4" TRS jacks.
• QudosXy HA800S — biggest trade-off: it's a line-level sub-mixer, not a microphone front end, and it runs on battery power rather than a fixed internal supply.
• Jectse 4 — biggest strength: four independent 3.5mm mic inputs feeding one stereo output, with per-channel volume knobs and built-in bias voltage so common electret and condenser mics need no extra power.
• Jectse 4 — biggest trade-off: it's built around 3.5mm mic-level connections, so it won't handle balanced 1/4" line gear the way the HA800S does.
• Pick the QudosXy HA800S if you're distributing and monitoring line-level audio across several sources or headphones.
• Pick the Jectse 4 if your problem is getting several microphones into one mix on a phone, tablet or computer.
Think of the HA800S as a traffic controller for line-level audio. Eight stereo channels, each with a dedicated volume knob and a STEREO/MONO switch, means you can take several sources — a mixer's outputs, an interface, a keyboard, a guitar rig — and hand each one its own place in the mix. The 1/4" TRS/TS jacks are the universal connector on studio desks, so it slots in without adapters. Inside, a 4580 low-noise op-amp is doing the work; that's a part chosen for low distortion and clean detail at higher volume, which is exactly what you want when you're monitoring rather than just listening.
The stereo/mono switching per channel is the feature I keep coming back to. Headphone monitoring is where this earns its keep — you can feed a stereo source to one pair of cans, flip a mono source to another, and adjust each independently. That's a rehearsal-room and home-studio workflow, not a podcasting one. The metal housing and palm-sized footprint (about 7.87" wide, 2.76" deep, under an inch tall) make it something you can throw in a bag for on-the-go recording or music teaching.
Who should skip it: anyone whose main need is plugging microphones straight in. There's no mic preamp here, no 3.5mm inputs, and no XLR. If your sources are condenser mics on a laptop, this is the wrong tool. Also note it's battery powered, so you're managing power rather than plugging into the wall — fine for portability, worth knowing if it's going to live on a desk permanently.
The Jectse 4 solves a narrower, very specific problem: four microphones, one output. Four independent 3.5mm input channels, each with its own volume knob, mixed down to a single stereo output that goes to headphones, speakers, a sound card or a computer mic input. If you've ever tried to juggle multiple condenser mics into one machine, you know why that matters — balancing them before they hit the recorder is far easier than fixing it afterward.
The 3.5mm interface carries built-in bias voltage, so common electret and condenser microphones work without a separate power supply. Plug them in and start mixing. Jectse rates the amplification at up to 4x, and the design uses rail-to-rail op amps for dynamic reproduction. The aluminum alloy body is a reasonable choice for something that's going to sit on a desk and get knocked around, and at 5.6 ounces with package dimensions around 5.12 x 2.76 x 1.57 inches, it's genuinely pocketable. It draws DC 5V.
Who should skip it: anyone working with balanced 1/4" line gear, instruments, or a multi-headphone monitoring setup. This is a mic mixer, not a line mixer. The outputs are stereo, but the inputs are all mic-level 3.5mm, and that's the boundary of what it does.
Side-by-Side: Which Should You Choose?
• Best for combining several microphones → Jectse 4. Four mic inputs, four volume knobs, one stereo out. That's the entire point of the device.
• Best for studio line gear and instruments → QudosXy HA800S. 1/4" TRS/TS jacks match mixers, interfaces, guitars, basses and keyboards directly.
• Best for phone, tablet and laptop setups → Jectse 4. Its 3.5mm interface and built-in bias voltage are aimed squarely at consumer and semi-pro devices.
• Best for portability → a tie, with a caveat. The HA800S is palm-sized metal and battery powered; the Jectse 4 is 5.6 ounces of aluminum alloy. Both travel well, but the HA800S needs power management.
• Best for clean, low-distortion monitoring at volume → QudosXy HA800S. The 4580 low-noise op-amp is specified for exactly that job.
• Best for a remote work audio chain → Jectse 4 if you're feeding mics into a computer or phone; QudosXy HA800S if you're routing and monitoring line-level audio on the desk.
For most people reading this with a microphone problem, I'd buy the Jectse 4. It does one thing — four mics into one clean stereo mix — and the built-in bias voltage plus 3.5mm compatibility mean it works with the gear you already own. In my opinion, the QudosXy HA800S is the better buy only if you specifically need multi-channel line-level routing and per-channel headphone monitoring. For a remote work setup where you're piping mics into a laptop or phone, the Jectse 4 is the more direct fit. Check the current price on Amazon before you commit.
how to connect studio headphones
For the QudosXy HA800S, plug your headphones into a 1/4" TRS output jack and use that channel's volume knob and STEREO/MONO switch to set the mode. For the Jectse 4, connect headphones to the stereo output and balance the four mic channels before you listen.
how to test studio headphones
Feed a known stereo source through the mixer and sweep the per-channel volume on the HA800S to check for noise and channel imbalance; its 4580 op-amp is specified for low distortion. On the Jectse 4, mute all but one mic channel at a time and listen for consistency across inputs.
how to bluetooth studio headphones
Neither device is a Bluetooth transmitter — both are wired. The HA800S uses 1/4" TRS jacks and the Jectse 4 uses 3.5mm connections, so you'd pair a separate Bluetooth transmitter with the output if you need wireless.
can you mix with just headphones
Yes, in the sense that both units support headphone monitoring from their outputs. The HA800S is built for it with eight independently controllable channels; the Jectse 4 lets you balance four mic inputs and monitor the summed stereo result.
As an Amazon Associate I earn from qualifying purchases.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon and affiliated sites.
When you buy through links on this page, we may earn a commission from qualifying purchases at no extra cost to you.
Amazon and the Amazon logo are trademarks of Amazon or its affiliates. This site is an independent third-party review and is not affiliated with, endorsed by, or sponsored by Amazon or the product brands mentioned.
See also: KOFIRE 2.4GHz/Wireless vs Yunsailing 20: Headphones for, our SOMIC Air One ANC vs Fosi Audio DS3 pick, XUMIUZIY Open Ear Headphones vs OPPWONG Kids, E-filliate DEWALT Heavy Duty vs LC-dolida Open-Ear Clip