We compare products from their published specs and features; the verdicts below are our independent editorial opinions.
Updated: 2026-09-30 · 8 min read · Independent comparison
If you want to turn a plain pair of 3.5mm headphones into a working mic-and-audio setup on a Windows PC, choose MOSWAG USB; if you need somewhere to actually put those headphones when you're done, choose HomeMount Headphone Hook. These two products solve completely different halves of the same problem, and the "headphones for Windows PC" question usually comes down to which half you're missing.
• MOSWAG USB — biggest strength: adds a real 3.5mm TRRS port (mic in + audio out) to a PC over USB with no driver install, using a built-in DAC chip rated for 16-bit/48kHz output.
• MOSWAG USB — biggest trade-off: it's an adapter, not a headset. It only helps if you already own a TRRS headset or mic, and the mic jack won't accept TS or TRS connectors.
• HomeMount Headphone Hook — biggest strength: a two-pack of adhesive desk hooks that hold up to 1 kg each, made from ABS and TPU with a non-slip pad to avoid scratching your gear.
• HomeMount Headphone Hook — biggest trade-off: it's pure storage. It does nothing for audio, connectivity or sound quality — and it needs a smooth surface plus a 24-hour settling period before you trust it with weight.
• Who each is for: MOSWAG USB is for someone whose PC has no usable 3.5mm jack (or only a headphone-only jack); HomeMount is for someone who already has working audio but a messy desk.
The MOSWAG USB is, at heart, an external sound card. It plugs into a USB port and presents your system with a 3.5mm TRRS aux port — one interface that carries both microphone input and audio output. That combination is the whole point. Plenty of desktop PCs, and a lot of laptops, either dropped the combo jack entirely or split mic and headphone into separate ports that don't play nicely with a single-cable gaming headset. This adapter collapses that back into one connection.
What it does best is get out of the way. There's no driver to hunt down: the manufacturer states plug-and-play, with the system auto-recognizing the device in seconds. The built-in DAC chip delivers stable 16-bit/48kHz output with a 95 dB signal-to-noise ratio and a 2.1 stereo surround configuration, and the spec sheet calls out effective noise reduction. It supports both CTIA and OMIP standard headphones, which matters because the two wiring standards are not interchangeable — a headset that works on one phone may not work on another device without the right adapter. The nylon-braided cable and aluminum shell are the durability story here; the brand frames them as longer-lasting than plastic-shell, PVC-cable alternatives. The cable runs 7.84 inches, which is short and tidy rather than a long tether.
Compatibility is broad on the USB side: Windows 10/9/8/7/Vista/XP, Linux, Mac OS X, Google Chromebook, Raspberry Pi, PS4, PS5 and Windows Surface 3.
Who should buy it: anyone running a TRRS headset or standalone TRRS mic who needs a working listen-and-talk port on a Windows PC, a laptop, a console, or a Raspberry Pi project. Who should skip it: anyone whose PC already has a combo jack that works fine — you'd be adding a dongle for nothing. Also skip it if your microphone uses a TS or TRS plug, because the 3.5mm male mic jack explicitly does not support those connectors. And if your actual problem is that your headphones have no home on the desk, this product is irrelevant to you.
The HomeMount Headphone Hook is a storage accessory, and it's honest about that. You get two hooks in the pack, black, in a simple straight shape. Each one attaches to the side of a desk or a computer case using a strong adhesive backing — no drilling, no clamp, no screws into your furniture. The body is high-quality ABS with TPU elements, which the brand describes as strong yet soft enough to avoid scratching or damaging your headphones.
The spec sheet gives a maximum weight recommendation of 5.1 pounds and a maximum weight capacity of 2 pounds, and the key features say each hook supports up to 1 kg. The install process is deliberate: peel the backing by hand, press the hook lightly into place on a smooth surface, then leave it for 24 hours before loading it up. That waiting period is the real trade-off. It's not a hook you install and immediately hang a heavy headset on.
What it does best is reclaim desk space. If your headset, controller or bag is constantly sliding around the desk, a hook on the side of the desk gets it off the work surface and within reach. The brand positions it for gamers specifically and lists XBOX, PS4 and PS5 controllers, desktop headsets, and even a desk purse among the things it can hold. It also works as a wall-mount alternative, and the brand suggests it as a small gift since it can hang headphones, cables, jewelry or schoolbags.
Who should buy it: anyone with a smooth desk edge or PC case side panel, a headset that lives on the desk, and a mild but constant annoyance about clutter. Who should skip it: anyone with a rough, textured, dusty or curved mounting surface where adhesive won't bite — and anyone who wants to hang something heavier than a typical headset and controller, because the stated capacity is a couple of pounds, not a bag of tools. And if your headphones don't connect to your PC at all, this hook won't fix that.
Side-by-Side: Which Should You Choose?
• Best for fixing "my PC won't recognize my headset mic" → MOSWAG USB. It adds the TRRS mic-in/audio-out port your machine is missing.
• Best for plug-and-play simplicity → MOSWAG USB. No driver required, auto-recognized in seconds per the manufacturer.
• Best for multi-device households → MOSWAG USB. Windows, Linux, Mac OS X, Chromebook, Raspberry Pi, PS4, PS5 and Surface 3 are all listed as compatible.
• Best for consoles and controllers → HomeMount Headphone Hook. The brand specifically names XBOX, PS4 and PS5 controllers among the things it holds.
• Best for damage protection → HomeMount Headphone Hook. The soft ABS/TPU build and non-slip pad are there to prevent scratches.
• Best for travel or a laptop bag → MOSWAG USB. The 7.84-inch braided cable and aluminum shell make it a small, packable item; the hooks are meant to stay stuck to one surface.
• Best for audio quality concerns → MOSWAG USB. The DAC chip, 16-bit/48kHz output and 95 dB SNR are the only audio-relevant specs in either sheet.
• Best if you just want a cleaner gaming setup → both, honestly. One fixes the connection, the other fixes the clutter.
If I had to pick one, I'd buy the MOSWAG USB — but only because of what "headphones for Windows PC" usually means in practice. The bottleneck is almost always the connection: a missing combo jack, a headset whose mic won't register, a laptop that only wants to output sound and never take input. A hook can't solve any of that; a USB sound card adapter can. In my opinion the MOSWAG is the higher-leverage purchase for anyone whose audio genuinely isn't working. The HomeMount is a genuinely nice, cheap-feeling-risk-free upgrade for a desk that's already functioning — I'd add it second, not first. If your sound already works and your only complaint is where the headset sits, flip the order.
how to connect headphones to windows pc
For a wired 3.5mm headset, plug it into the PC's audio jack and pick it as the output device in your sound settings. If your PC has no combo jack, or the mic won't register, that's exactly what the MOSWAG USB is for: it adds a 3.5mm TRRS mic-in and audio-out port over a plain USB connection, no driver required. Your system should recognize it automatically within seconds.
how to connect headphones to pc windows 10
On Windows 10 specifically, the MOSWAG USB lists Windows 10 as a supported platform, so it's a plug-and-play route: connect the adapter to a USB port, plug your TRRS headset into the 3.5mm jack, and let Windows auto-detect the device. Then set it as your default playback and recording device. Keep in mind the mic jack only accepts TRRS connectors — not TS or TRS.
how can i connect my headphones to my pc
Two paths. If your headset is TRRS and your PC has a working combo jack, just plug it in. If it doesn't, a USB sound card adapter like the MOSWAG is the fix — it presents a 3.5mm port carrying both mic and audio over USB. Note that the HomeMount hook has nothing to do with connecting anything; it's purely a place to hang your headphones afterward.
how to use headphones on pc
Once connected, select the device as your default output in your sound settings and confirm your mic is picked up as the input. The MOSWAG's DAC chip handles the conversion at 16-bit/48kHz with a 95 dB signal-to-noise ratio, and it supports both CTIA and OMIP headphone standards. If you're comparing options, check the current price on Amazon before deciding, since that's the one thing these spec sheets don't cover.
As an Amazon Associate I earn from qualifying purchases.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon and affiliated sites.
When you buy through links on this page, we may earn a commission from qualifying purchases at no extra cost to you.
Amazon and the Amazon logo are trademarks of Amazon or its affiliates. This site is an independent third-party review and is not affiliated with, endorsed by, or sponsored by Amazon or the product brands mentioned.
See also: PowerA LucidSound LS500X vs HyperX Cloud Stinger 3, iclever vs belkin kids headphones, Kefiany 3.5mm vs GZLMMY Neckband Earphones, YUSONIC Headphones vs rockpapa 3.5mm