研究著作

清華動機系博士論文

Thermal Optimal Design for Fully-Confined Compact Heat Sinks by Using Various Optimization Methods

國立台灣工業技術學院 碩士論文

Feature-based sheetmetal bending design and development system

期刊發表

1. 黃惠珠、陳琨旻、林永隆、洪振聰, 2022,應用智慧製造技術於鏟花品質檢測之研究, 中國機械工程學會第三十九屆全國學術研討會論文集 #D1-023,pp.107-111, 國立聯合大學 苗栗市。

2. 王旻楊, 曾浚祐, 洪振聰, 林永隆, 2022,應用反應曲面法於SKD11工具鋼線切割放電加工加工參數最佳化之研究, 中國機械工程學會第三十九屆全國學術研討會論文集 #D2-010,pp.268-273, 國立聯合大學 苗栗市。

3. 洪振聰、黃惠珠、王旻揚 、林永隆,2021,雕模放電加工之專家系統開發研究,中國機械工程學會第三十八屆全國學術研討會論文集 #D2-005,國立成功大學 台南市，pp.296-301。

4. 洪振聰、王旻揚、林永隆,2020,應用類神經網路與基因演算法於木工機吸塵螺帽之最佳化設計, 中國機械工程學會第三十七屆全國學術研討會論文集#270,雲林縣虎尾鎮.

5. 林永隆 、林冠宏、洪振聰 ,2019,木工機銑刀吸塵螺帽之最佳化設計，中國機械工程學會第三十六屆全國學術研討會論文集#00202,台北市。

6. 洪振聰、林冠宏、林永隆、吳全士,2018,應用類神經網路與基因演算法於預熱塞之最佳化設計,中國機械工程學會第三十五屆全國學術研討會論文集#0108,嘉義縣,pp.1864-1869.

7. 洪振聰,吳全士,洪清鏈,2017,預熱塞中鐵-鉻-鋁線(Fe-Cr-Al)與鎳線(Ni)長度與線徑變化對穩態時間與溫度之影響研究,中國機械工程學會第34屆學術研討會論文集#10727,台中市。

8. 洪振聰,黃柏諭,2016，應用反應曲面法(RSM)於預熱塞之鐵-鉻-鋁線(Fe-Cr-Al)與鎳線(Ni) 長度最佳化設計研究, 中國機械工程學會第33屆學術研討會論文集#1264,新竹市。

9. Jenn-Tsong Horng, Nun-Ming Liu, Ko-Ta Chiang, 2008, Investigating the Machinability evaluation in the hard turning of Hadfield steel with Al2O3/TiC mixed ceramic tool based on the response surface methodology Journal of Material Processing Technology, 208 (1-3), pp. 532-541. (SCI)

10. Te-Chang Tsai, Jenn-Tsong Horng, Chih-Chung Chou, Ko-Ta Chiang, 2008, The effect of heterogeneous second phase on the machinability evaluation of spheroidal graphite cast irons in the WEDM process, Materials & Design, Vol.29, pp.1762-1767. (SCI)

11. Jenn-Tsong Horng, Ko-Ta Chiang, 2008, A grey and fuzzy algorithms integrated approach to the optimization of turning Hadfield steel with Al2O3/TiC mixed ceramic tool, Journal of Material Processing Technology, Vol. 207 , September, pp.89-97. (SCI).

12. Horng, J. T., Chang, S. F., Wu, T. Y.,Chen, P. L., and Hung, Y. H., 2008, Thermal Optimal Design for Parallel Plain-FinHeat Sinks by Using Neuro-Genetic Method, IEEE Transactions on Components andPackaging Technologies, Vol. 31, No. 2, June 2008, pp.449-460. (SCI)

13. Nun-Ming Liu, Jenn-Tsong Horng, Ko-Ta Chiang, 2008, The method of grey-fuzzy logic for optimizing multi-response problem during the manufacturing process: a case study of the light guide plate printing process, International Journal of Advanced Manufacturing Technology, inpress. (SCI)

14. Kuang-Yuan Kung, Jenn-Tsong Horng, Ko-Ta Chiang, 2007, Material removal rate and electrode wear ratio study on the powder mixed electrical discharge machining of cobalt-bonded tungsten carbide, International Journal of Advanced Manufacturing Technology, inpress. (SCI)

15. Chen, H. T., Chen, P. L., Horng, J. T., and Hung, Y. H., 2005, Design Optimization for Pin-Fin Heat Sinks, ASMEJournal of Electronic Packaging, Vol.127, No.4, December 2005, pp.397-406.(SCI)

16. Chen H. T., Horng, J. T., Chen, P. L., and Hung, Y. H., 2004, Optimal Design for PPF Heat Sinks in Electronics Cooling Applications, ASME Journal of Electronic Packaging,Volume 126, Issue 4, December 2004, Pages 410-422. (SCI)

17. Wu,T. Y., Wu, M. C., Horng, J. T.,Chang, S. F., Chen, P. L. and Hung, Y. H. ,2007,」 Thermal Optimal Design for HeatSinks or Heat Sink/TEC Assemblies in a Ducted Flow,」International Electronic Packaging Technical Conference and Exhibition, July8-12, Vancouver, Canada.(EI)

18. Wu, M. C., Wu, T. Y., Horng, J. T., Chang, S. F., Chen, P. L. and Hung, Y. H. ,2007, A Semi-Empirically Thermal Optimization for Heat Sink/TEC Assemblies with Various External Thermal Resistances, International Electronic Packaging Technical Conference and Exhibition, July 8-12, Vancouver, Canada. (EI)

19. Peng,C. H., Wu, M. C., Lee , C. Y., Horng, J.T., Fang, C. J., and Hung, Y. H., 2006, An Optimal Approach with GeneticAlgorithm for Thermal Performance of Heat Sink/TEC Assembly, Itherm 2006, SanDiego, CA, USA, May 30-June 2. (EI)

20. Chen, H. T., Chen, P. L., Horng, J. T., Chang, S. F., Wu, T. Y., and Hung, Y. H., 2006, Thermal Design Optimization for Strip-Fin Heat Sinks with a Ducted Air Flow, Itherm 2006, San Diego, CA, USA, May 30-June 2. (EI)

21. Wu, T. Y., Wang, M. P., Horng, J. T., Chang, S. F., and Hung, Y. H., 2005, Forced Convective Heat Transfer for Partially-Confined Compact PPF Heat Sinks with Top-Bypass Effect, IPACK2005-73121, Proceedings of InterPACK'05, International Electronic Packaging Technical Conference and Exhibition, San Francisco, USA, July 17-22. (EI)

22. Wang, M. P., Chen, H. T., Horng, J. T., Wu, T. Y., Chen, P. L., and Hung, Y. H., 2005, Thermal Optimal Design for Partially-Confined Compact Heat Sinks, IPACK2005-73118, Proceedings of InterPACK'05, International Electronic Packaging Technical Conference and Exhibition, San Francisco, USA, July 17-22. (EI)

23. Wang, M. P., Wu, T. Y., Horng, J. T., Lee, C. Y., and Hung, Y. H., 2005, Fluid Flow Characteristics for Partially-Confined Compact PPF Heat Sinks, HT2005-72225, Proceedings of HT2005, 2005 ASME Summer Heat Transfer Conference, San Francisco, USA, July 17-22. (EI)

24. Chai, T. S., Horng, J. T., Wu, T. Y., and Hung, Y. H., 2004, Thermal Performance Measurement for Confined Heat Sinks, ITHERM 2004, Ninth Intersociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems, pp.302-309, Las Vegas, NV, USA, June 1-4. (EI)

25. 江可達,洪振聰,張福平,2001, 『自然對流狀態下散熱片冷卻方式之改進』,修平學報,第三 期, pp.47-65.

26. Lin,Z.C. and J.T. Horng, 2000, 「Feature-Based Sheet Metal Design and Development System」, International Journal of Materials and Product Technology, Vol.15, No.6, pp.471-494.(SCI)

27. 江可達,洪振聰,1999, 『樹德工商專科學校二年制夜間部學生來源分析統計』,樹德學報,第 二十三期, pp.225-243.

28. Lin,Z.C. and J.T. Horng,1998,」 Sheet Metal Products Database in Support of their Process Planning and Surface Development」, International Journal of Computer Integrated Manufacturing, Vol.11,No.6, pp.542-533. (SCI)

29. Lin,Z,C and J.T. Horng , 1996, 「Geometric Data of the Object-Oriented Program Method and Development Rule for Thin Sheet Metal Product」, CSNE, Journal of Chinese Society of Mechanical Engineers, Vol.17,No.3,pp.213-219.

30. 林榮慶,洪振聰, 『鈑金設計與展開資料庫研究』, 中國機械工程學會第十一屆學術研討會 論文集,第 87-94 頁,台中市(1994)