erteza tawsif efaz

Welcome to my personal webpage.

My name is Erteza Tawsif Efaz, I was born on 20^th September in Chittagong, Bangladesh. To be a scientist is my aim in life, and as such, after graduation, I have dedicated myself to the improvement of photovoltaics, robotics, and bio-electronics. Except for research, I have a special penchant for swimming, mountaineering, parachuting, health, and fitness training.

Object Detection and Classification by Cascade Object Training, 2020, Supervisor: Ahmed Masud Chowdhury, Graduate Student, Indiana University - Purdue University Indianapolis, United States.

• Computer vision prototype is proposed regarding smart observation trained by Cascade Trainer GUI.

• Overseas work completed as a corresponding author, tested algorithm efficacy using S32V234-EVB2.

Enhance Cell Performance of DSSC by Dye Mixture, Carbon Nanotube & Post TiCl₄ Treatment along with Degradation Study, 2020, Supervisor: Fahmid Kabir, Graduate Student, University of Dhaka, Bangladesh.

• Employing betalain-curcumin extracts as sensitizers at a 1:2 ratio on FTO/SWCNT-TiO₂-treated DSSC.

• Funded experimentation completed as a team member, gathered few test data using Spectrometer.

An Automated Agricultural Shading for Crops with Multiple Controls, 2020, Supervisor: Jafrina Jabin, Graduate Student, North South University, Bangladesh.

• Implementing wireless-embedded system as actuator for a stepper motor via NXP/FRDM-K64F MCU.

• Funded experimentation completed as a team member, deployed hand gesture module using Laser.

Development of a Low-cost Real-time Bioelectrical Signal Acquisition Module, 2020, Supervisor: Md. Shah Kamal, Graduate Student, University of Dhaka, Bangladesh.

• Processing human-body variable as electrogram through a medical equipment consisting FIR/IIR LPF.

• Funded experimentation completed as a team member, composed simple hardware unit using Amp.

A Review of Primary Technologies of Thin-film Solar Cells, 2019, Supervisor: Md. Meganur Rhaman, Professor, Ahsanullah University of Science & Technology, Bangladesh.

• Have discussed best research modules with material property by comparing a-Si, CIGS, and CdTe cells.

• The independent investigation completed as a team lead, plotted all graphical illustrations using XLS.

Deep CNN-supported Ensemble CADx Architecture to Diagnose Malaria by Medical Image, 2019, Supervisor: Khandaker Lubaba Bashar, Assistant Professor, Ahsanullah University of Science & Technology, Bangladesh.

• Have presented better diagnosis model with fewer computation by utilizing deep-CNN architectures.

• The independent investigation completed as a team lead, operated all microscopic images using ML.

Modeling of a High-speed and Cost-effective FPV Quadcopter for Surveillance, 2019, Supervisor: Md. Meganur Rhaman, Professor, Ahsanullah University of Science & Technology, Bangladesh.

• Introduced flight-controller stack with brushless motors to develop light/durable/multipurpose UAV.

• Collaborative research completed as a team manager, simulated the control systems using Simulink.

Parametric Analysis of CdTe/CdS Thin Film Solar Cell, 2016, Supervisor: Safayat Al Imam, Assistant Professor, Ahsanullah University of Science & Technology, Bangladesh.

• Emphasized electron-hole mobility with varying thickness to investigate BC/CdTe/CdS/TCO/GS TFSC.

• Undergraduate research completed as a team manager, evaluated the efficiency facts using MATLAB.

Design of an Indicative Featured and Speed Controlled Obstacle Avoiding Robot, 2018, Supervisor: Md. Meganur Rhaman, Professor, Ahsanullah University of Science & Technology, Bangladesh.

• To unite autonomous mobile robot with a buzzer and RGB diffused LED to indicate and control speed.

• A collaborative project completed as a 1^st contributor, fabricated an intelligent vehicle using Arduino.

Mini Solar Grid, 2016, Supervisor: Safayat Al Imam, Assistant Professor, Ahsanullah University of Science & Technology, Bangladesh.

• To design interconnected solar houses with a meter and DC battery bank to store and supply energy.

• An undergraduate project completed as a 1^st contributor, implemented an electrical circuit using PV.

8-bit PC with Assembly Language, 2017, Course: Microprocessor, Interfacing & System Design Lab, Ahsanullah University of Science & Technology, Bangladesh.

• Transfer of data with 16 operational performances and compiler model to programmable computer.

• Collaborative assignment completed as a group leader, rendered a device architecture using Chipset.

Nanotechnology for Healthcare, 2016, Course: Biomedical Instrumentation Lab, Ahsanullah University of Science & Technology, Bangladesh.

• Enhancement of humans with DNA fixing nanobot and antibacterial bot for advanced bioelectronics.

• Undergraduate assignment completed as a group leader, demonstrated a factual lecture using PPTX.

• Arduino Project Hub giveaway reward as a full contributor in robotics, May 2018.

• EdX Financial Assistance approved discount as a course learner in astronautics, August 2016.

• Daily First Light accorded reception as a talented student in school, August 2008.

Thank you for your time.