v25n5

1. 터보펌프의 기액이상류 특성 ( Characteristics of Turbo Pumps Operating in Air-Water Two-Phase Flow )

2. 선박공조장치 설계계획과 공조방법 ( Program Phase and Air-Conditioning systems of ship )

3. 가변 추진장치의 이해 ( Controllable Pitch Propeller )

4. 박용디젤기관의 질소산화물 저감기술 ( Nox Reduction Technologies on Marine Diesel Engines )]

5. TBT 함유 방오페인트의 국제규제에 관한 국내현황 및 대책 ( A Domestic Situations and Response on the Golbal Prohibition of TBT compounds on the Ship's Anti-fouling System )

6. 정규배열내의 실린더 사이에서의 완전발달된 층류 유동의 기하학적 계수의 해석 ( Analysis of Geometric Parameters for Fully Developed Laminar Flow Between Cylinders Arranged in Regular Array )

7. 송전선의 전선도약 해석에 관한 연구 ( A Study on the Analysis of Galloping for Power Transmission Line )

8. 피로균열전파수명의 확률분포추정 프로그램 개발 ( Development of Probability Distribution Estimation Program for Fatique Crack Growth Lives )

9. 교류발전기 병렬운전시 과도현상 해석에 관한 연구 ( A Study on the Transient Phenomenon Analysis at the instant of Parallel Running for A. C. Generators )

10. 사각채널내 와동발생기가 부착된 원형실린더 하류 유동 특성에 대한 실험적 연구 ( Experimental Investigation of Flow Characteristics by Wing Type Vortex Generators Set up Behind a Circular Cylinder in a Rectangular Channel )

11. 시간지연을 갖는 제어대상에 대한 P, PI 제어의 유효 게인 조정 범위에 관한 연구 ( A Study on the Permissible Gain Ranges of the P and PI Controllers for the Retarded Processes )

12. 풍력발전용 공기터빈의 최적설계에 관한 기초 연구 ( A Basis Study on Optimum Design of Air Turbine for Wind Power Generation )

13. 전기응집 및 탈수 시스템을 이용한 슬러지 함수율 저감 특성 ( Performance Evaluation of Electrocoagulation and Electrodewatering for the Reduction of Water Content in Wastewater Sludge )

14. 원자로 압력용기용 강의 고온피로특성에 미치는 응력비의 영향 ( Effect of Stress Ration on Fatigue Crack Propagation Behavior of Pressure Vessel Steel SA516-Grade70 at High Temperature )

15. 선박용 위성 안테나용 트랙킹 알고리즘 ( A Tracking Algorithm for Shipboard Satellite Antenna Systems )

16. 습식 수중 아크용접봉의 국산화개발에 관한 기초연구 ( A Basic Study on the Development of Domestic Underwater Wet Arc Welding Electrode )

17. 3차원 공간에서 코일스프링의 강성에 관한 연구 ( A Study on the Stiffness of Coil Spring in the Three Dimensional Space )

18. 층간파괴인성치에 미치는 성형압력의 영향에 관한 연구 ( A Study on the Effect of Molding Pressure on the Interlaminar Fracture Toughness )

19. 가솔린 기관에서 최적의 시동 및 공회적 속도제어를 위한 전자 제어장치 개발에 관한 연구 ( A Study on the Development of an Electronic Control System for Optimal Start and Idle Speed Control in Gasoline Engines )