v24n6

1. 함부르그 조선, 선박기자재 및 해양기술 국제무역박람회 ( SMM 2000 )를 다녀와서

2. 기관축계의 비선형 다자유도 강제 비틀림 진동에 관한 연구 ( A Study on the Non-linear Forced Torsional Vibration for Propulsion Shaftings with Multi-Degree-of-Freedom System )

3. 곡관덕트에서 난류맥동유동의 축방향 속도분포와 2차유동속도분포 ( Axial Direction Velocity and Secondary Flow Distributions of Turbulent Pulsating Flows in a Curved Duct )

4. J-적분과 균열선단개구변위에 관한 구속계수 m의 평가 ( An Estimation of Constraint Factor on the J-δ_t Relationship )

5. 인버터로 구동되는 유도전동기의 정수 및 특성에 관한 연구

6. 박용 대형 저속 디젤기관 연료분사계통의 시뮬레이션에 관한 연구 ( A Study on a Simulation of a Fuel Injection System in a Large Low-Speed Marine Diesel Engines )

7. 유전알고리즘을 이용한 컨테이너 크레인 시스템의 위치제어 및 흔들림 억제를 위한 퍼지 제어기 설계 ( Design of a Fuzzy Controller for Position Control and Anti-Swing in Container Crane Systems Using Genetic Algorithms )

8. 마그네트론 스퍼터링법을 이용한 Indium-Tin Oxide 박막의 제작과 그 특성에 관한 연구

9. Ti-6Al-4V재의 전기화학적부식 거동에 미치는 시효열처리의 영향 ( The Effect of Age Heat-treatment to the Electro-Chemical Corrosion Behavior on Ti-6Al-4V )

10. SCM440강 용접부의 내식성에 미치는 용접후 열처리효과에 관한 전기화학적 연구

11. 원형단면 노즐의 급확대 축소부를 통한 유동손실에 대한 연구 ( A Study on the Flow Loss for Sudden Expansion and Contraction Part of Circular Pipe Nozzle )

12. 곡관덕트에서 LDV를 이용한 천이정상유동의 유동특성에 관한 연구 (Ⅰ) ( A Study on the Flow Characteristics of Developing Transitional Steady Flows in a Curved Duct by Using Laser Doppler Velocimeter (Ⅰ) )

13. 새로운 MRAS에 의한 유도전동기의 센서리스 속도제어 ( Novel MRAS Based Sensorless Speed Control of Induction Motor )

14. 터보과급디젤기관의 급가속 운전시 압축기출구에의 공기분사가 응답성능에 미치는 영향 ( The Effects of Air Injection in Compressor Exit on the Response Performance of a Turbocharged Diesel Engine under the Operating Conditions of Rapid Acceleration )

15. 음향 여기에 의한 혼합층 유동구조의 변화에 대한 연구 ( The Study on Changes of Mixing Layer Caused by Acoustic Excitation )

16. 발전용 가스엔진의 개발 및 연소특성에 관한 연구 ( A Study on the Development and the Combustion Characteristics of a Stationary Gas Engine )

17. RF 스퍼터링법에 의한 Al-Sn계 코팅 베어링의 제작과 특성 평가 ( Preparation of Al-Sn Coating Bearings by RF Sputtering Method and Evaluation of Their Properties )

18. 롤러 프로파일링을 고려한 박용 디젤기관 캠-롤러 사이의 탄성유체윤활해석 ( Elastohydrodynamic Lubrication Analysis on the Cam-Roller for a Marine Diesel Engine with Consideration of Roller Profiling )

19. 자동차용 전자제어식 부변속기 개발 ( Development of an Electronically Controlled Transfer Case for Automobile )